Bedini Earth Light

[cgalvisardila]

Sounds Good

The rock crystal that I used to get the two volts and I showed in my latest videos is called Hematite. Hematite - Wikipedia, the free encyclopedia

that sounds pretty great man, i would like to see the results of the test that chuck proposed (the probe clip outside the water) also, you don't say anything about current, have you measured it? we all would appreciate it if you did these tests since you have the rock already, let us know and if the result is still as good, ill definitely buy some rocks... for now it sounds pretty promising, thanks IB

carlos

[ibpointless2]

The rock crystal that I used to get the two volts and I showed in my latest videos is called Hematite. Hematite - Wikipedia, the free encyclopedia

It is basically iron-oxide, and its mined as the main ore for iron. The reason why I used it as a electrode was that its already been exposed to water and the environment so I don't need to worry about it corroding. You won't find the metals we use in our cells laying around, they're usually rusted or have a oxide layer on them and they must be heated up to remove the oxide layer and that leaves you with the plain metal. Hematite is heated up and the oxygen is removed and your left with iron/steel. Iron will always want to go back to hematite so why not just use hematite, nature's electrode? Hematite will always want to be the positive electrode so that means carbon, copper, and titanium will be the negative electrode and since most of these are corrosion resistant we can have electrodes that will out live us. So now it doesn't matter what crystal solution you use (to a certain degree). There is other ore's out their we can use too!

Here is where i bought my hematite, they gave me a extra gift of some more crystals too. HEMATITE ROUGH ROCKs - 1 LB Lots - Healing - Lapidary | eBay

[John_Bedini]

I have 60Hz Transformer circuit on Crystal Cell

NickZ,
I have a circuit running, now I have not adjusted it yet, super bright lights and my crystal cells runs these easy. All is you do is use any transformer with the BJT and the base resistor is 1K the capacitor is .01 to 1uf. If you make the capacitor big like 220 uf ( Base +) will blink bright, you can also drive the led's from the 120 volt output. I did one thing different I put the led's across the whole input inductor. I'm going to try different devices next. I used a standard MPS8099 that was laying on my bench for now. but it does work good. The thing that I have noticed right away the MA meter readings are false and can not be depended on. I must go find a current probe around here to see what is going on. I do not know if I believe Robbie's circuit yet as far as the meter readings go. I find some tricks with the circuit that I do not think were explained to those working on this circuit. I will run a video when I'm done. 2N2222 better gain capicator .01uf
John B

[ibpointless2]

IBpointless2, I loved that you went over 2 volts by hooking up to a rock. Have you ever tried hooking up to thorium?

,Shawn

Nope never tried it. Its radioactive and is slowly attacked by water, so it won't make a good electrode. But i might try gallium. Thanks.

[ibpointless2]

Ibpointless2:
Would you please check the voltage and CURRENT of your last test with the clip lead out of the water. As the clip lead is a metal. Also the rock from your picture is hard to see. Less water would help and keep the lead out. The rock looks to have some Basalt? and Quartz? Not sure where you live so I don't know the rock in your area. Also it looks to have a sediment layer in the middle that is very, very dark as well as porous. A fare test would be to dry your rock and perform the test again. Please post results with this test if you can.

Chuck H

Hi Chuck thank you for your concern about the clip lead, but their is no way that the metal of the clip lead and magnesium could ever give over 2 volts with using tap water. Before I went to bed i posted a video of me testing the rock with other metals and found that the rock always likes to be positive. Rock electrode makes other electrodes negative - YouTube

I didn't find the rock i bought it from eBay. The person who i bought it from also gave me a free gift which is another rock that is "conductive" too, you probably see it in the video to the right, its a orange-yellow rock. I'll see if i can shoot a video of this again to show that its not the clip lead. Cheers.

[shawnnweed]

IBpointless2, I loved that you went over 2 volts by hooking up to a rock. Have you ever tried hooking up to thorium?

,Shawn

[griplets]

First Post

Hi All,

This is my first post, my name is Alex (AKA Griplets on Youtube). I have been following this thread almost everyday for the last year or so and have decided to weigh in. Have not built anything yet but I will soon... following John's formula.

My first question relates to the "Manganese (III) Oxide (Mn2o3)" in John Bedini's formula; I have noted that a number of people are quoting it as (and possibly also using) Manganese (IV) Dioxide (MnO2). From what I read on Wiki they are quite different and I have been wondering why some people are using the latter?

Fausto & Lidmotor thank you for our videos. John Bedini I hope to meet you one day.

[blackchisel97]

In dec 2007 I purchased a new U1P-7 lawn and tractor battery and dumped the acid mix out. I refilled it with a alum solution (McCormick's Ammonium Aluminum Sulfate and distilled water). I charged and discharged it 5 times using 'West Mountain Radio's Computerized Battery Analyzer'. It then sat on a shelf untill sept 2009 when I repeated the tests again. It showed a standing voltage of aprox 11.6volts and the discharge curve continued below where it would if it was a lead acid. I took it off the shelf again and am charging it now to run another round of tests. The pics show charts of the 2007 and 2009 tests.

Mike Klimesh

Mike Klimesh I sent you PM.

Vtech

[mklimesh]

Alum conversion for lead acid batteries

In dec 2007 I purchased a new U1P-7 lawn and tractor battery and dumped the acid mix out. I refilled it with a alum solution (McCormick's Ammonium Aluminum Sulfate and distilled water). I charged and discharged it 5 times using 'West Mountain Radio's Computerized Battery Analyzer'. It then sat on a shelf untill sept 2009 when I repeated the tests again. It showed a standing voltage of aprox 11.6volts and the discharge curve continued below where it would if it was a lead acid. I took it off the shelf again and am charging it now to run another round of tests. The pics show charts of the 2007 and 2009 tests.

Mike Klimesh

[chuck H]

Clip lead in water

I was able to break the 2 volt barrier today! in-order to break the 2 volt barrier I had to use a rock as one of the electrodes. The picture is below. Can anyone guess what rock that is, its a very common rock.

I used tap water and the positive goes to the rock and the negative goes to the magnesium ribbon.

[ATTACH]10397[/ATTACH]

Ibpointless2:
Would you please check the voltage and CURRENT of your last test with the clip lead out of the water. As the clip lead is a metal. Also the rock from your picture is hard to see. Less water would help and keep the lead out. The rock looks to have some Basalt? and Quartz? Not sure where you live so I don't know the rock in your area. Also it looks to have a sediment layer in the middle that is very, very dark as well as porous. A fare test would be to dry your rock and perform the test again. Please post results with this test if you can.

Chuck H

[ibpointless2]

I was able to break the 2 volt barrier today! in-order to break the 2 volt barrier I had to use a rock as one of the electrodes. The picture is below. Can anyone guess what rock that is, its a very common rock.

I used tap water and the positive goes to the rock and the negative goes to the magnesium ribbon.

[ATTACH]10397[/ATTACH]

This 2 volts was from just one cell. I never had one cell give me over 2 volts before, the highest i ever got was 1.8 volts but I had to use vinegar, this is just plain tap water.

What I've found was that the rock always like to be the positive electrode. this means that even Carbon/graphite would act like a negative electrode and so would copper and titanium. This is odd since i'm use to copper being the positive electrode. This is a good thing when you consider titanium is very corrosion resistant so it will make a good negative electrode. I'm still trying to figure this rock out. Does anyone have a guessed what this rock might be?

[ibpointless2]

I was able to break the 2 volt barrier today! in-order to break the 2 volt barrier I had to use a rock as one of the electrodes. The picture is below. Can anyone guess what rock that is, its a very common rock.

I used tap water and the positive goes to the rock and the negative goes to the magnesium ribbon.

[cgalvisardila]

Iron Pyrite Fused With Coper

I built a cell fusing the Cu with pyrite with very satisfactory results, steady current for long time, little water needed... i think this is a great idea, thanks john.


Pyrite - copper fused cell - YouTube

[John_Bedini]

I also trust the results that Lidmotor will reveal.

Thanks John, that sounds great. I await your next steps.
I also trust the results that Lidmotor will reveal.

As mentioned in the other forum I will not judge or criticize any ones work, but my own. I am trying to avoid any more conflict, as I love this thread, and electronics in general, which I worked on at several different jobs for about 15 years. I don't want to add to any further hardships that will encumber our goals. We all want the same thing which is the truth, and not more BS. Although it may not seam like it, at times.
Nick

NickZ,
I do not want to be judged as unfair here so I let him speak. Outside of that we continue the work here. People have the right to do the experiments for themselves. I'm building the cell now so someone besides me can test.
John B

[NickZ]

Thanks John, that sounds great. I await your next steps.
I also trust the results that Lidmotor will reveal.

As mentioned in the other forum I will not judge or criticize any ones work, but my own. I am trying to avoid any more conflict, as I love this thread, and electronics in general, which I worked on at several different jobs for about 15 years. I don't want to add to any further hardships that will encumber our goals. We all want the same thing which is the truth, and not more BS. Although it may not seam like it, at times.
Nick