Peter Daysh Davey Water Heater Query

[RAMSET]

special transformer build ?

Fellows
Most of these tuning issues will disappear if we can build the transformer
That Mr.D referred to?

That being a variable transformer that makes 1-2 KW within our cycle window !
This can be done cheaply as Daemonbart said using recycled heat pump boards and parts ...if we work together open source !

This is the course we must take!!

I look Forward to that thread!!

Chet

[wrtner]

Hi All

What is the best method to find out at what hz my electricity is running at.

we have 50hz here in U.K

how would we build the circuit to test the exact frequecny hz,
example it could be 49hz it could be 50hz it could be 51hz

somebody mentioned using a diode and speaker , can somebody give the
exact circuit and exact diode for this.

thankyou

Jimmyx1000

It is not a diode; it is a fat resistor, high wattage, value depending
on the loudspeaker being used. It is connected in series with the speaker
and then across the mains.

Then, you will hear the frequency (or an octave thereof - NOT a harmonic)
and should tune directly to it.

The basic note, 50hz (or 60hz in the States and other countries) is
PHENOMENALLY low. Cheap speakers will get you octaves. You should
try for the real thing if possible.

To see how staggeringly low it is, if you have Windows 98, ME, XP
or Vista, try this free software:
Electronic Piano - Free software downloads and software reviews - CNET Download.com

To the output of the sound card, you need a good speaker or preferably quality earplugs.

There are two Octave sliders; both MUST be set "Octave 1".

The UK note will be around G, "w" on the keyboard which will be difficult to hear because it is so low. The "o" (between "i" and "p", and not zero) is a full octave higher.

In the US, it will be 60hz, between B flat and B , between "4" and "r". The note between "_" and "[" is fully an octave too high.

These notes are seriously low. See for yourselves.

Paul-R

[kenssurplus]

Hi Jimmy,

My suggestion would be to use a laptop running on a battery (to avoid mains freq interferrence) and using this free software:

DL4YHF's Audio Spectrum Analyser

One of its features is:
Frequency resolution in the sub-milliHertz range (exceeding the stability of the soundcard's clock generator).

you can zoom in the range that you want to look at, say for example from 20 hz to 100 hz to correctly nail down what your specific frequency is.

Then place your laptop or microphone next to something running on your mains power (preferrably something with a bigger transformer or motor etc.).

Just listening to transformer hum through vibrations in the table, I can tell the frequency of my off grid inverter is at 61.05 hz.

Hope this helps

[jimmyx1000]

Best method to work out frequency of my Electricty hz (50hz)

Hi All

What is the best method to find out at what hz my electricity is running at.

we have 50hz here in U.K

how would we build the circuit to test the exact frequecny hz,
example it could be 49hz it could be 50hz it could be 51hz

somebody mentioned using a diode and speaker , can somebody give the
exact circuit and exact diode for this.

thankyou

Jimmyx1000

[jimmyx1000]

Regarding the Ring or Cap that goes around the can ?

Hi All

regarding just the ring going around the aluminium can.

I was just wondering regarding the ring that goes around the can
at 300hz or 400hz ,

by cutting and making the can ring to exact measurments is this making it
vibrate at 300hz or 400hz,

once whe have made the ring for the can, do we not test the ring itself to see if vibrates at 300hz or 400hz.

in other words if ring is cut to exact measurments , it will vibrate at 300hz or 400hz according to the model being made, us or europe.

thankyou

Jimmyx1000

[Cherryman]

I believe Zinc will loose its sacrificial property when it is heated, not sure at which temperature, so you should look into that.

Here a 101:

Cathodic Protection 101

[boguslaw]

What is the way to slowdown galvanic corrosion between aluminium, stainless steel and brass ? Beer can is aluminium, ring/cap (neutral electrode) is SS and most common pipe system is copper + brass.
I thought about zinc from batteries. Anybody experienced ?

[PhysicsProf]

On another thread, I extended an offer of a New Renaissance Prize last December. The reception was enthusiastic and now I have extended the prize this past week.

Things are moving! Four of the Silver Eagle awards have already been awarded, and one Thousand-Euro prize has been given out also. (You may guess who this is... he is a principal on this thread.) Please see this thread for details:

http://www.energeticforum.com/renewa...menters-3.html (post #78 especially)

DaemonBart and others -- I hope you will consider this offering as a way to reward inventors such as yourself and at the same time, for your research to be a blessing to humanity. Something we all want!

[RAMSET]

Thank you for doing this !!

Mr. D

This will be an Opportunity to expand our knowledge of the world around us !
Professor Savic Has opened a door that will not be closed!
For this we will be forever grateful !!

I have been driven with a personal goal to leave this world a better place than I found it, And I know many other men and women here feel the same way.
We will do everything we can to assist in any way possible for this knowledge to be shared Open Source!!


Thank you
Chet
PS
Water hides some very simple secrets
I love simplicity.... and so does My Father [the one upstairs]

[daemonbart]

Inverter

Hi AM!

I am working with IGBT modules from scrap inverter heat-pumps. My first and working setup is from other components but will be hard to replicate, and expensive.

The IGBT modules are perfect for our use in boiler, I guess I will blow some of them from start

I hope some of us could work in open source with the setup

I want to say also, this inverter driver will not alone make sonic boiler OU!

The inverter is a good start for many of you I think!

I hope to start a thread dedicated for this later today!

Kind rgds D

So, do you have a variable frequency inverter or are you doing it with a car alternator+motor+variac?

Regards

M

[AhuraMazda]

A couple of videos from witts that I had not seem before:

[www.witts.ws] WITTS Hemisphere Quantum Fuelless Generator - Demo #2 - YouTube

WITTS Hemisphere Quantum Fuelless Generator - Demo #1 [www.witts.ws] - YouTube

[PhysicsProf]

Professor Jones,
You will soon have in your possession Tesla's secret termo resonance high technology.
Please Apply cleverly nikakao the military and war against the purposes of wildlife on the planet.
The amount of energy in the vacuum is infinite it is constantly being revised and circulated.
Black holes devouring matter in the universe and transformed into neutrinos (high frequency), and the stars in the universe is re-created and translated into a (low frequency)
Further explanations will give you how to measure COP sonic boiler and mount the dish with water.
When you get the sonic boiler (Quantum heater) because it takes energy from the quantum field let me know.
prof.Savić, Serbia

It is an exciting time -- and I thank Prof Savic for being willing to share his device -- which is being sent to a fellow energy researcher in western Europe for further testing, at my request. (It is not being sent to the US at this time.) Thank you Slovenia.

I look forward to the "further explanations", especially how to mount the dish in water.

Thank you sincerely, Professor Savic! And I also thank and acknowledge the contributions of the many researchers working on this New Energy Technology throughout the world!

[Slovenia]

Mr. "C" Message to Professor Jones

Professor Jones,
You will soon have in your possession Tesla's secret termo resonance high technology.
Please Apply cleverly nikakao the military and war against the purposes of wildlife on the planet.
The amount of energy in the vacuum is infinite it is constantly being revised and circulated.
Black holes devouring matter in the universe and transformed into neutrinos (high frequency), and the stars in the universe is re-created and translated into a (low frequency)
Further explanations will give you how to measure COP sonic boiler and mount the dish with water.
When you get the sonic boiler (Quantum heater) because it takes energy from the quantum field let me know.
prof.Savić, Serbia

[osamaricu_te]

Sir
With all respect Your handle that you use here seems strange?
I try not to judge a book by its cover .

We are an open source community ,people that come to these pages
I have known most of them a long time ...as does Slovenia.

Persons that share their hard work here have a certain Quality that is usually reflected in how they Speak, Their handles [forum names] ETC
You seem a bit out of line with what I have come to expect from the benevolent men and women that come here to make this world a better place?

A little Off To Me...................

Can you explain your handle [forum name] Please?

Thank you
Chet

I make it a rule to try and accommodate anyone asking nicely, so I will extend the same rule to you.
I made this account few months a go, while my reading of EF goes much longer. At that time I must have been in a good mood and being extremely immature person at certain aspects for my age and status (I train that part of me on daily basis to keep it that way, playing games and being childish with my kids at some points), I used this nick... Now if you were to ask me WHY, dont really know and who cares? Does it say something to you, perhaps me not being benevolent...?

Now to more important matters, been doing some tests last night, with 2 frequencies. Used 4 plates this time, they were thin but too thick to get any "sound" response from them with my amplifier, so I turned 2 plates in "dummy" plates and again I got around unity response.

Then I used 4 different plates, made of aluminum, VERY thin. Those responded with my amplifier very nicely, BUT to keep up with power from socket at 50Hz, I turned my amplifier to the very end. It seems I pushed this amplifier a bit more than he can handle :P

So in the end, I got no particular news to report other than being 2 amplifiers short now.
Both burned out. Feel sorry about this last one, it was a strong one, bought for this

Anyway, will stop here, try to think about another approach. Should I get any ideas, will post here.

bb for now

[Michael John Nunnerley]

Can you describe it further ? I'm ready to try to build this magnetic amplifier to regulate current from my power socket into sonic boiler.I have a yoke ferrite core from dismounted from old pc monitor.Would it be good one for it ? I know that the essence is to have proper winding directions so AC voltage do not occur on 9V side, can you post any link to successful building of such magnetic amplifier with instructions ?

Hi

First off, I am in France, had to sign myself out of hospital as my brother inlaw was found dead in his flat in the north of France, today is the funeral.

The magnetic amplifier is made up of two separate transformers, it must not be all on one core as it works as an out of phase saturation of the cores. It is conected as shown in the circuit, the pot varies the amount of saturation of the cores, amplification can be up to 100 times when using the diodes as shown.

I think this will work very well with what you are doing, I have not tested this with your application, but with a light bulb it works as I have stated "resistive load".

Mike