Muller generator replication by Romerouk

[toranarod]

@Toranarod, what is the diameter of your new rotorand how many magnets do you have on it? Is your iron core laminated? If so, how many laminations? I just ordered ten 10mmx10mm N42 magnets.

One more question, what type of bearing are you using?

Regards,

Zooty

I use a heavy auto motive bearing. Its from the V Belt Idler Pulley from my Toyota
You can get one from any car they are cheap and easy to make this is what I have done











8 magnets inserted into a solid billet of PVC. 150 mm Dia. Each magnet extends out by 5 mm making total diameter 160 mm

I will get back to you on the laminates

[Zooty]

@Toranarod, what is the diameter of your new rotorand how many magnets do you have on it? Is your iron core laminated? If so, how many laminations? I just ordered ten 10mmx10mm N42 magnets.

One more question, what type of bearing are you using?

Regards,

Zooty

[toranarod]

This is a good circuit you should build this and test it.
this will be very useful for a this application.

[MonsieurM]

Excellent!

now your seeing it :

what i can tell you for sure is once your mind realizes the true meaning of fractal, and that it is not just in the shape of nature but also in the process/engine...well let's put it this way, the shape becomes the engine

[penno64]

Hi Rod,

Great work. Keep it goiing.

I was just unsure if the gen coil was the single 9mH inductor or some
fance footwork with the twin coil which at first looks appears to be drive coil.

Kindest Regards, Penno.

[toranarod]

[yx630514]

Hi toranarod
I noticed Muller replica circuit, In between Hall and the MOSFET driver, There is a 555 oscillator circuit, It seems the role is to produce more output tip - peak.

[elias]

if you are winding new coils I would go with the slider coil setup.

just be mind full of coil to magnet ratio.

My magnets are 4.5cm in diameter and my cores are about 38mm in diameter. What is the slider coil setup?

Thanks

[yx630514]

Hi toranarod
Thank you very detailed description of response.
My voltage is too low, Only 12V. 20V voltage regulator to work after, Circuit is working properly.
But: load (CFLs) are still only can intermittent flashes(flashing very fast), Not always continuous light.

How should I continue to the next?

[penno64]

Hi Rod,

Is that what is used for the setup at the top of this page ?

Regards, Penno

[toranarod]

Hi toranarod
I follow you to provide circuit experiment
But it does not work,
Examination revealed: IRF9630 (G) and MJE13003 (E) 10K resistor connected between the cancellation and direct connection to work.
Please confirm the circuit belong to the right?
See attached images.
Thank you

I have checked the circuit. This is my lay out I will look over it some more

what is the supply rail voltage it was basically set up for 25 to 70 volts supply.
you must be above 20 volts for it to function properly.

[yx630514]

Circuit does not work

Hi toranarod
I follow you to provide circuit experiment
But it does not work,
Examination revealed: IRF9630 (G) and MJE13003 (E) 10K resistor connected between the cancellation and direct connection to work.
Please confirm the circuit belong to the right?
See attached images.
Thank you

[penno64]

Hi Rod,

Yeah, I am near Parramatta, NSW.

Is the coil set at 6 O'clock the drive coil and the single inductor at 7 O'clock
the generator coil?

Also, the mags - you spec down to 10mm but 10mm x ???

What sort of power are you whacking into it ?


Regards, Penno

[toranarod]

My Muller generator is repaired: ‪My repaired Muller motor generator‬‏ - YouTube
How do you recommend to wind my coils, currently they are about 200 turns of 2 strands of 1mm wires.

if you are winding new coils I would go with the slider coil setup.

just be mind full of coil to magnet ratio.

[elias]

My Muller generator is repaired: ‪My repaired Muller motor generator‬‏ - YouTube
How do you recommend to wind my coils, currently they are about 200 turns of 2 strands of 1mm wires.