Muller generator replication by Romerouk

[penno64]

Thanks Slider

[Slider2732]

Hi Penno,
The FanGen does it all the time, but the clear plastic box motor doesn't. Am aiming at seeing exactly what is different on both. Does a Bedini SSG light a neon at rest ? that would answer much.
In fact, however, the FanGen tester motor runs much better if the PC fan driving circuit is disabled, found that out by accident the other day.

The coil is connected as normal, but the neon just sits on the back too, in parallel with the coil wires. I just soldered it there and figured it would show if I was getting 90V and above back out. Being as there is no filament it doesn't bother the DC going in, but reacts to the HV going out

Great idea Rod for splitting the coil work ! Driving one from the other is something I can't wait to hear the results of

[penno64]

@Slider,

Were you ever able to recreate the neon lighting effect on the stationary
rotor ?

I am still puzzled by your statement, the neon is connected across the coils
output! I thougt we input to the coil to drive the rotor.

I simply amazes me that at 12v input, you are able to fully light a 80-90v neon before the BEMF sipkes are created by the mobing rotor mags.

Penno

[toranarod]

attraction and Repulsion

here is my next variation on the litz wire coil.

I am testing as many wiring configuration as possible and taking watts and current measurements looking at the most efficient variation.

So far I am down to 1.3 ratio of under unity as the best figures so far.



140 mill amps at 280 volts out








My next round of test will be to drive one side from the other

[Joit]

I wont read that again, but

"A nice little write up posted by Nul Points at OU. Like I have said, there are many interesting things to be said about PLAYING WITH STRANDS...

Quote from Null Points:

"The darker and lighter lines represent the two windings, OF THE SAME SIZE WIRE, in which the first winding is connected in series to the second winding".

Null Point's experiment has nothing whatsoever to do with STRANDS. Null Point's experiment involves A SINGLE WIRE!

Do you understand what TWO WINDINGS Mean? No Matter, if they are in Serie or Parallel connected ??
That means you HAVE 2 Strands. And NO MATTER, If this 2 Strands have the same Size.
Windings mean, You Place Wire OVER or CLOSE to eachother.

They get the Idea, but sorry, You dont.

And not matter, how they Call it, violating Lenz or Ohms Law, its both realated.
Even when you it Magnetic Resistance, not Lenz Law, well he describes it with his Law.
And a Resistance in a Circuit creates allways Back Electro Magnetic Force,
no matter, how you create it, over a Phyiscal Resistance, like a Neon Bulb
and the Wire in there, or with a additional Coil, where the Current runs opposite, or you short it.

That may even would work with a simple Coil with a lot Windings with Thicker Wire on it,
and a smaller Wire inside, or at one End from this Coil.

[admin]

We have noticed this thread going in a direction that is not respectful of the Forum Guidelines.

Please respect these Guidelines or we will need to take further action.

Thank you.

[Joit]

Synchro,
How the Topic did start there, Romero stated, that it did not work with 2 small Pulses. He mainly agreed, that he used 4 Coils to drive, one Pair at Top, One Pair at bottom.
This Configuration from Romero has still a Drag on the Rotor, so it dont seems like, he did additional short one Coil more, even, it would not help really, when he has 7 other Generator Coils, and only one Coil short, to get higher Voltage, that dont work, because it will equal to the lower Amount at the Cap.
Plus it makes additional Drag on the Rotor. One Video what is out there from the Guy what drives a Rotor only with switches or Transistors is a Fake. That dont works.
Plus, the Circuit is not set like, that it would make Sense, to short only one Coil.

[Joit]

Quote from Bruce:

"A nice little write up posted by Nul Points at OU. Like I have said, there are many interesting things to be said about PLAYING WITH STRANDS...

Quote from Null Points:

"The darker and lighter lines represent the two windings, OF THE SAME SIZE WIRE, in which the first winding is connected in series to the second winding".

Null Point's experiment has nothing whatsoever to do with STRANDS. Null Point's experiment involves A SINGLE WIRE!

JOIT,

My understanding is there are 5 magnets and 9 coils. How can the magnets be 180 degrees apart when they're an odd number? Don't you think it's more likely the 2nd Hall is narrowing the pulse width like the 2nd reed switch in Ozzie Calanan's break even circuit, rather then supplying a second serial power pulse? Along with tapering the power pulse, the 2nd Hall can slmultaniously open the output gate.

Also, what's the "red button on top" comment you made refer to? You must think there's something real bright about useing Vacuum tubes in the age of the Arduino laptop programed ROM.

Synchro
Regarding Posting #743? Thats where i did Quote you. Is this to much for you?

Go Back and READ IT. Are You really only out for a Fight here?

You still use any of your Postings to put something in Where you can offend Bruce Further?

Man, go back to Ou.com, that Place there really fits for you.

[synchro]

Null Points.

Quote from Bruce:

"A nice little write up posted by Nul Points at OU. Like I have said, there are many interesting things to be said about PLAYING WITH STRANDS...

Quote from Null Points:

"The darker and lighter lines represent the two windings, OF THE SAME SIZE WIRE, in which the first winding is connected in series to the second winding".

Null Point's experiment has nothing whatsoever to do with STRANDS. Null Point's experiment involves A SINGLE WIRE!

JOIT,

My understanding is there are 5 magnets and 9 coils. How can the magnets be 180 degrees apart when they're an odd number? Don't you think it's more likely the 2nd Hall is narrowing the pulse width like the 2nd reed switch in Ozzie Calanan's break even circuit, rather then supplying a second serial power pulse? Along with tapering the power pulse, the 2nd Hall can slmultaniously open the output gate.

Also, what's the "red button on top" comment you made refer to? You must think there's something real bright about useing Vacuum tubes in the age of the Arduino laptop programed ROM.

[Joit]

Joit,

What's your explaination for the 2nd Hall?

[eastcoastwilly]

Bruce,

I am willing to bet you any amount of money, and I can produce backers to help, that all your claims of generating any kind of verifiable overunity gain are completely false, and that you are the lier, not me! Now let's see how much money you can come up with to back up your malarky! I dare you.

Joit,

What's your explaination for the 2nd Hall?

Please stop posting stuff that has absolutely nothing to do with this thread. There is Private Messaging for bickering and whatnot.

Thanks for your consideration,

Will

[synchro]

Bruce's OU Claims.

Bruce,

I am willing to bet you any amount of money, and I can produce backers to help, that all your claims of generating any kind of verifiable overunity gain are completely false, and that you are the lier, not me! Now let's see how much money you can come up with to back up your malarky! I dare you.

Joit,

What's your explaination for the 2nd Hall?

[redrichie]

Did he do it? :
YouTube - ‪quest for OU XI -- "M-G long-runner"‬‏

[toranarod]

http://www.overunity.com/index.php?action=dlattach;topic=3842.0;attach=54280

Lota

Hello lota

welcome.. Nice circuit diagram.
keep us informed of you progress

good luck

[lota]

http://www.overunity.com/index.php?action=dlattach;topic=3842.0;attach=54280

Lota