ENLIGHTENED MAGNETISM (The Full Proof of Ken Wheeler's Theories)

[Ufopolitics]

hola Ufo
I fully agree with your assertions above quoted as I have observed in my setup the same effects you describe even with such a poor and rough construction.

Well that means you understood pretty well Ken's words...like a fragment from page 71 about repulsion (counter-voidance):

Far right are two likewise spin fields causing deflection; this is mirror membrane Ether deflection, this is literally extremely high-pressure space,

Your disclosure here of the same concept (better developed of course) fills my soul with a kind of indescribable joy because I posted a pic short time ago in OU forum, but did not received the slighest echo, and now I received a qualified confirmation of my thoughts and observations. Thank you for that.

Regards
Alvaro

Alvaro, "better developed" means tons of hours of development...tons of experiments, tons of models built...tons of money invested...as tons of frustrations...

I do not believe anyone could be able to... just from Ken's Book writings... produce -straight forward- the model you are looking above on my SCIFI Generator...without going through several steps of development my friend!!

In order to get people's attention ("echo") on a specific model...you must show "Extraordinary Results"...

My pleasure friend. However, this small machine proves something beyond its "results"...it proves that by just moving A VIRTUAL FIELD through an Iron Core, it produces an EMF on the Wire conductors wrapped around that core.

How big or how small of an EMF is determined by the spec's of its construction...But that is not relevant either.

For example, have you thought that if a Spatial Field, mass-less, weight-less... moving through an iron core produces an EMF...

Couldn't we just spin that virtual field then, without moving "It's Carrier" (in this case those magnets)...and still produce an EMF?

I mean, if you look again at this device, it is absolutely Not The Magnet Embodiment what is causing the EMF, but the Magnetic Field it "carries" SPATIALLY.

Think of it, analyze it slowly...and then look at "the Bigger Picture" beyond the Machine, and behind this experiments...

This Machine lead me to the Static Armature Rotating the Virtual Fields project...which is my "Bigger Picture"...

Actually, generating the same type of field (either North or South) to obtain a Spatial Repulsion Field, which do not reverses its polarization...leads to not reversing its voltage at coils...so it is even easier to make it happen...I did it on My All North (or All South) Asymmetric Machines ...


Regards


Ufopolitics

[interdesign21]

Hello to All,

The faster we spin that mass-less, weight-less and transparent field around iron core-coils assembly...the more EMF we will get in their output terminals...simple.

We take off the Iron Core...and no Induction is Generated...

We set an Attraction Field, a so called "Uniform Field" by adding Two Opposite Arc Magnets facing each others...and ABSOLUTELY NO INDUCTION is Generated...

We take off the Magnets...and absolutely nothing happens, no matter how fast we spin rotor....

A SOUTH REPULSION SPATIAL FIELD would Generate an EMF which is COMPLETELY OPPOSITE SPIN , AND OPPOSITE SINEWAVE as that of a NORTH REPULSION SPATIAL FIELD...IF WE keep the SAME ROTATION SENSE IN BOTH FIELDS TESTING...

Which concludes that South and North SPATIAL COMPRESSED FIELDS have OPPOSITE Spins WHEN FACING EACH OTHERS...like I have shown on some of my videos, which are NOT FINISHED YET...

Concluding, this Machine shows that by JUST spinning this TRANSPARENT, COMPRESSED SPATIAL FIELD which is completely MASS-LESS, WEIGHT-LESS...around the Iron Core...We obtain an EMF Output...

Lenz Reversed Forces are generated, but in the Vector Direction of the ROTOR SPIN which is PERPENDICULAR to Both B-Fields of the SAME POLARITY COMPRESSED FIELD.

Therefore Lenz can not "catch" this Spatial Field...

We can load this Generator and we see absolutely no Increase on the Prime Mover Amperage Nor Voltage CONSUMPTION...NONE

We short circuit the output terminals and we observe an acceleration of its rotor beyond the Prime Mover constant speed, fed by the Power Source.

And, this Spatial Compressed Field is "expandable" along the Iron Rotor Path...so, the more Rings we add...the stronger the Field would be...

When the Repulsion Forces become GREATER THAN the Attraction Forces to Iron Core...there is absolutely NO MAGNETIC DRAG.

So, our Prime Mover spends "Nickels and Dimes"...in Energy Input.

[Ufopolitics]

Thanks Ufo,
Good explanation for this layman.

I already have a generator head without the engine just collecting dust and wishful looks from me. Many old motors, generators, etc. Will get to some replication next week to have some more fun and learn more.

This weekend I'm kidnapped by wife of 38 years celebrating anniversary and sneaking a peek at your latest postings. Shhhhhhhhhh...........

Thanks from a greatful layman,
wantomake

Happy Anniversary Wantomake!!

Cheers


Ufopolitics

[wantomake]

Always a layman

Hey Bro Mikey!!

Let me tell you that if there is a guy who I want to fully understand what am doing here... is you, my friend!

Ok, let me start from the beginning...better that way...as I would go without any technical vocabulary related to this Theory...just from a Layman point of view...


You know that every Home Generator have a "Head" (We call it Generator Head) which is the Electrical part and the Gas Engine is attached to it...

The Head have a center Rotor where a DC Field (One or Two Coils) is energized during use of Generator, By spinning this heavy mass rotor along with its energized coils, a Magnetic Field is also spinning with it , which is in charge to Induce the EMF on the Generating Static Coils that are at the Outer Generator Housing.

This Rotor Shaft is the one which connects "direct drive" to the Gas Engine.

Ok, so what I did?

I took off the Gas Engine...

I took off Gas Tank...

I took apart the gen head and took off the heavy iron mass Rotor Assembly...

Then I replaced that spinning rotor by a Static Armature (or you could also call it "Static Rotor")...even it don't make sense...... from a modified DC Motor armature that fits pretty tight in there...then I am showing how it works...and how it is wound.

This Static Armature Coils are connected to this Power Rotary Switch...in order that when I spin that little Motor attached to the switch, with 3 to 6 Volts...it starts spinning a VIRTUAL FIELD inside the armature...so by spinning this Virtual, Mass-Less, Weight-Less and transparent Field...we get Energy out...

The Generator Outer Housing and its Generating Coils don't need ANY modification at all.


Please tell me if you understand it better now...


Regards Friend!


Ufopolitics

Thanks Ufo,
Good explanation for this layman.

I already have a generator head without the engine just collecting dust and wishful looks from me. Many old motors, generators, etc. Will get to some replication next week to have some more fun and learn more.

This weekend I'm kidnapped by wife of 38 years celebrating anniversary and sneaking a peek at your latest postings. Shhhhhhhhhh...........

Thanks from a greatful layman,
wantomake

[Ufopolitics]

A bit more about the Learning Machines...

Hello to All,

I will start by quoting myself on just a segment from the First Post where I started this Disclosure.

Hello to All,

[...]

1-On my bench , I am working on a small device that utilizes a Compressed Spatial Field*, (Yes, *a Spatial Field in the middle of an empty transparent massless space) from Magnetic Repulsion that Induces an EMF on several coils when just passing through these coils wrapped around an iron core, even at low speed...The "Prime Mover" is a very small Asymmetric Motor that I built for this purpose, and it consumes very little current while it develops the required speed and torque to spin the device's rotor...And this device have the capability that when its generating coils are plainly shorted, (wire terminal to wire terminal) it increases the speed of its rotor beyond the prime mover constant speed...I called this device a SCIFI Induction Generator...yes "SCI-FI" on purpose..., as it also means "Spatially Compressed Interacting Field Influence"...

2-I have also another device that uses a mechanical-electrical rotary switch, based on a very small motor powering it...very small, but carrying the enough force to be able to transfer a very strong, mass-less and weight-less magnetic field, amplified by huge STATIC iron cores. This Field transfers from each iron core element to another, adjacent...I call it "Field Mutation" for the simple fact that the Magnetic Field is forced to "switch" from one Statiic iron structure to another Static iron structure...And so, while this Field Mutates in a rotational fashion, it projects its EMF Induction Capabilities to another series of predisposed ALSO STATIC coils...which could be exactly the same kind as the ones every single home generator have as "Generating Stator Fields"...without absolutely any modification.[...]

Above are the TWO MACHINES descriptions which FULLY demonstrates that the SPATIAL Magnetic Fields ARE ROTATIONAL AND DIVERGENT. And NOT like they have taught Us all.

I should have disclosed first the Number One (1) Machine above, in detail...but I did not and I just "Jumped" You all to the far more "Advanced" Machine.


Sorry about that...

I did not do it, because I am "upgrading" it with new stronger Neodymium N52 Grade Magnets in order that results are much higher....and that requires re-balancing of the entire rotor assembly plus modifying all the magnets mounting components...

The Spatially Compressed Interacting Fields Influence (SCIFI) Induction Generator would demonstrate that a completely SPATIAL FIELD, suspended in the middle of the empty space... between Two Arc Segments Magnets in Repulsion, when INFLUENCING an Iron Core...would be ACCELERATING the Iron Particles in a Spiral Pattern...

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

Therefore, when we start TRANSLATION of that Compressed Field along the Iron Core, We would be generating a FORWARD SPINNING GRADIENT WAVE...That could be measured in our Scopes.

Now, when we install a series of Coils which wrap around such Iron Core...they will be Generating an EMF...like shown below

[IMG][/IMG]

[IMG][/IMG]

The faster we spin that mass-less, weight-less and transparent field around iron core-coils assembly...the more EMF we will get in their output terminals...simple.

We take off the Iron Core...and no Induction is Generated...

We set an Attraction Field, a so called "Uniform Field" by adding Two Opposite Arc Magnets facing each others...and ABSOLUTELY NO INDUCTION is Generated...

We take off the Magnets...and absolutely nothing happens, no matter how fast we spin rotor....

A SOUTH REPULSION SPATIAL FIELD would Generate an EMF which is COMPLETELY OPPOSITE SPIN , AND OPPOSITE SINEWAVE as that of a NORTH REPULSION SPATIAL FIELD...IF WE keep the SAME ROTATION SENSE IN BOTH FIELDS TESTING...

Which concludes that South and North SPATIAL COMPRESSED FIELDS have OPPOSITE Spins WHEN FACING EACH OTHERS...like I have shown on some of my videos, which are NOT FINISHED YET...

Concluding, this Machine shows that by JUST spinning this TRANSPARENT, COMPRESSED SPATIAL FIELD which is completely MASS-LESS, WEIGHT-LESS...around the Iron Core...We obtain an EMF Output...

Lenz Reversed Forces are generated, but in the Vector Direction of the ROTOR SPIN which is PERPENDICULAR to Both B-Fields of the SAME POLARITY COMPRESSED FIELD.

Therefore Lenz can not "catch" this Spatial Field...

We can load this Generator and we see absolutely no Increase on the Prime Mover Amperage Nor Voltage CONSUMPTION...NONE

We short circuit the output terminals and we observe an acceleration of its rotor beyond the Prime Mover constant speed, fed by the Power Source.

And, this Spatial Compressed Field is "expandable" along the Iron Rotor Path...so, the more Rings we add...the stronger the Field would be...

When the Repulsion Forces become GREATER THAN the Attraction Forces to Iron Core...there is absolutely NO MAGNETIC DRAG.

So, our Prime Mover spends "Nickels and Dimes"...in Energy Input.

There are MUCH MORE Improvements that this Machine could have...like adding a Motoring Effect sets of Coils, without interfering -at all- with the Generation Output...

So, after You see this Machine performing (which should be -hopefully- next week, after am finished then filming it...)...I believe it would be much easier to "digest" and visualize the Virtual Field Spinning inside our Static Armatures installed within an Unmodified Generator Head Housing Assy...which I have been disclosing previously.

It is simple to know that our Virtual Fields are Spinning for real...that Center Iron Rotor MUST Spin if the Field Spins.

If it just "shakes" and vibrates, then our set up is not working...and we will get a scrambled EMF Out...which could propulse a Motor...but NOT Strong enough.

And so, We could also install another iron rotor, ring shaped in the outer surface of our armatures (before installing it inside Gen Head Housing, of course)...mounted in Axial Bearings...to verify, our Virtual Field is spinning in a completely SMOOTH FASHION...just like a DC Motor spins its Armature/Rotor...

The Rotary Power Switch Assy is an EXTREMELY USEFUL TOOL to start building it FIRST...THIS IS THE "HEART PUMP" of the whole design, As this Switch Assy Could be used in MANY, many Different Set Ups...by just replacing the Commutators and Wiring Circuit to more complex designs. The Brushes are conceived in order they could be adapted to different diameter commutators.

I will be first showing a Detailed Video on how to put it together...after I finish the SCIFI Induction Generator Machine Video.

[IMG][/IMG]

[IMG][/IMG]

Above are a couple of recent images from the SCIFI INDUCTION GENERATOR...being Upgraded


Regards to All.


Ufopolitics

[Ufopolitics]

Hey UFO, count me in on builders thread, surely i can find something laying around here to modify to spec.

Warm regards Cornboy.

Hey old Friend!!

It is great news to hear you will be joining Us in the Building Threads...

I consider You one of the GREATEST BUILDER, on this whole FORUM.

Then I will wait to hear from MachineAlive...another EXCELLENT BUILDER.

We need You ALL, to help me demonstrate ALL of this Projects work, and they are real.

TO THE MACHINES!


Warm Regards


Ufopolitics

[Cornboy 555]

Hey UFO, count me in on builders thread, surely i can find something laying around here to modify to spec.

Warm regards Cornboy.

[BroMikey]

Hey Bro Mikey!!

Let me tell you that if there is a guy who I want to fully understand what am doing here... is you, my friend!

This Static Armature Coils are connected to this Power Rotary
Switch...in order that when I spin that little Motor attached to the
switch, with 3 to 6 Volts...it starts spinning a VIRTUAL FIELD inside
the armature...so by spinning this Virtual, Mass-Less, Weight-Less
and transparent Field...we get Energy out...
The Generator Outer Housing and its Generating Coils don't need
ANY modification at all.
Please tell me if you understand it better now...

Regards Friend!
Ufopolitics

Okay now I get it really clear thanks again. That is a cool idea and I will
be watching to see what you are about to show us all in your wonderful
class room adventure. Thumbs up to you 4 all of the open
source goodies displayed on so many of your THREADS.

Me seize it now.

I have searched many college and University libraries in my travels of
the USA plus internet information. No where have I found a resource
such as the ENERGETICFORUM where inventor get down to business
showing the beginning and the end.

Many books are filled with fluffy filler to sell and unending stream in the
series of whatever it is called but your stuff gets down to brass tacts
without another 4 years of english-math and who knows what else.

What a great way for people to study on line. On the other hand the books
offered on this site as well as the information not yet bound always has
the same effect of giving us all a practical application.

Your mock up just as described should prove to be interesting that I
will not want to miss. I am beginning to see motor timing, that is not much
but I am happy with learning something new on both paper and with my
hands on experiments.

I bought a commutator off ebay for $8 and am learning fast on another
project. Thank you for your patience to reiterate so many times the same
message in a new way for a new day. You are a motor King.

[Ufopolitics]

Careful there UFO, I don't want to tell you your business but don't let impedance sneak up and bite you in the rear. You may be using DC, but it's not a constant DC to your static armature coils. The series wound coils between the two positive and also the two negative brushes are effectively shorted out, no current flows. So the field collapses and then rebuilds when each coil sees a pos and neg brush at it's ends. The current takes time to build and that is when impedance will manifest and it will have a frequency according to RPM. As the RPM and frequency increases the effective resistance of each coil will increase. You might also want to investigate the coil inductance and how long it takes a coil to build it's magnetic field.

These things might not be all that important in the end but I don't think they should be discarded out of hand, especially if you intend to run at high RPM.

Regards,

CM

Thanks Cadman!

I know it takes a while to fully understand this set up...as I know exactly what you mean, referring to the two set of coils "in between" the two positive brushes as the other side between the two negative brushes.

I call those Coils the "Idling Coils"...So, I do understand your worry.

Let me explain it again a bit more in detail, related to your concern.

First let me ask you to concentrate on the Two "V" Planes configured by each two Brushes, Positive and Negative.

So, One V Plane would be opening a North Pole, while the other V Plane would be opening the South Pole...just like : (North Pole>+<South Pole) where the "+" is the center of armature and switch and the ><while the remaining series coils within the V Plane are still energized so the Field, within that V Plane, will not collapse.

Realize that both of the V Planes Rotate comprehending always a number of energized coils within.

Originally I have tested this system with only Two Brushes (no idling coils) and it works as well. But we are wasting energy on coils which would not induce an EMF...PLUS. I use idling as a cooling stage...And here, you could see what I mean better, because the Armature is always getting energized majority of its total coils, just like in a Symmetrical DC Brushed Motor takes place.

The Four brushes design is conceived when we get refined, adjusting the Interacting Virtual Field Angle of projection for even better results.

But it is great to have concerns...as always we will find some "issues" on the way to the end that may need some work...

Regards


Ufopolitics

[Cadman]

caution

This Armature field receives a DC feed, rectified by the existing diodes, the same way the OEM Rotor Field does.

Thanks

Ufopolitics

Careful there UFO, I don't want to tell you your business but don't let impedance sneak up and bite you in the rear. You may be using DC, but it's not a constant DC to your static armature coils. The series wound coils between the two positive and also the two negative brushes are effectively shorted out, no current flows. So the field collapses and then rebuilds when each coil sees a pos and neg brush at it's ends. The current takes time to build and that is when impedance will manifest and it will have a frequency according to RPM. As the RPM and frequency increases the effective resistance of each coil will increase. You might also want to investigate the coil inductance and how long it takes a coil to build it's magnetic field.

These things might not be all that important in the end but I don't think they should be discarded out of hand, especially if you intend to run at high RPM.

Regards,

CM

[Ufopolitics]

Wow thanks 4 sharing these shots of your research, this takes it out
of the theoretical (Which we must have) and puts the thread in the
tangible. So awesome. I have grown to respect your research effects
not only with your ability to express things graphically but the actual build.

Even tho I don't understand it fully. Thanks to all who really love this
research. I am just starting out trying to understand what it
is that is being said, I see that you say it is a switch and then all the wires
go over to the cage with windings.

I'll be quiet and keep looking. Even tho I don't get it yet I am
certain that your project has taken much of your life to get this far. What
a man, thanks UFO for giving to us.

Am I the only one who does not understand the switch?
A switch that rotates but the cage sit over there?
Maybe I need to re-read.

Hey Bro Mikey!!

Let me tell you that if there is a guy who I want to fully understand what am doing here... is you, my friend!

Ok, let me start from the beginning...better that way...as I would go without any technical vocabulary related to this Theory...just from a Layman point of view...


You know that every Home Generator have a "Head" (We call it Generator Head) which is the Electrical part and the Gas Engine is attached to it...

The Head have a center Rotor where a DC Field (One or Two Coils) is energized during use of Generator, By spinning this heavy mass rotor along with its energized coils, a Magnetic Field is also spinning with it , which is in charge to Induce the EMF on the Generating Static Coils that are at the Outer Generator Housing.

This Rotor Shaft is the one which connects "direct drive" to the Gas Engine.

Ok, so what I did?

I took off the Gas Engine...

I took off Gas Tank...

I took apart the gen head and took off the heavy iron mass Rotor Assembly...

Then I replaced that spinning rotor by a Static Armature (or you could also call it "Static Rotor")...even it don't make sense...... from a modified DC Motor armature that fits pretty tight in there...then I am showing how it works...and how it is wound.

This Static Armature Coils are connected to this Power Rotary Switch...in order that when I spin that little Motor attached to the switch, with 3 to 6 Volts...it starts spinning a VIRTUAL FIELD inside the armature...so by spinning this Virtual, Mass-Less, Weight-Less and transparent Field...we get Energy out...

The Generator Outer Housing and its Generating Coils don't need ANY modification at all.


Please tell me if you understand it better now...


Regards Friend!


Ufopolitics

[BroMikey]

[IMG][/IMG]

[IMG][/IMG]


[IMG][/IMG]

Now, honestly, did you ever, in your wildest dreams about Free Energy...ever thought that such small little motor could TURN a Home AC Generator Head and produce power out?





Regards


Ufopolitics

Wow thanks 4 sharing these shots of your research, this takes it out
of the theoretical (Which we must have) and puts the thread in the
tangible. So awesome. I have grown to respect your research effects
not only with your ability to express things graphically but the actual build.

Even tho I don't understand it fully. Thanks to all who really love this
research. I am just starting out trying to understand what it
is that is being said, I see that you say it is a switch and then all the wires
go over to the cage with windings.

I'll be quiet and keep looking. Even tho I don't get it yet I am
certain that your project has taken much of your life to get this far. What
a man, thanks UFO for giving to us.

Am I the only one who does not understand the switch?
A switch that rotates but the cage sit over there?
Maybe I need to re-read.

[Ufopolitics]

Yes, 4 coils with a resistance of 30 ohms each in series will give a total of 120 ohms, and two sets of 4 coils in parallel will give a total of 60 ohms.

But the impedance under (pulsed = AC) working conditions may be totally different.

Electrical impedance - Wikipedia, the free encyclopedia

This Armature field receives a DC feed, rectified by the existing diodes, the same way the OEM Rotor Field does.

Thanks


Ufopolitics

[dR-Green]

Wonder why caps disappeared. R?

Yeah the same happened to mine, strange.

[dR-Green]

Thanks Guys!

So, coming from an OEM Coil of 60 Ohms, then we need 120 Ohms on each Parallel Group in Series of Four Coils each.

So, that means it is Double the Resistance per Coil...meaning, from my previous wrong example : it is then 30 Ohms and not 15 per each coil in series. (30X4=120)

The problem I see here is that if I wind a much finer gauge, to achieve a higher resistance per coil in less space, I would be decreasing the Magnetic Field Strength...And I don't want to do that.

An easy solution would be to expand the number of coils energized per group...without going a smaller gauge.

I guess it won't matter that much to expand the Field.


Regards


Ufopolitics

Yes, 4 coils with a resistance of 30 ohms each in series will give a total of 120 ohms, and two sets of 4 coils in parallel will give a total of 60 ohms.

But the impedance under (pulsed = AC) working conditions may be totally different.

Electrical impedance - Wikipedia, the free encyclopedia