Motor Generators

[bistander]

...

Next do the same thing with a fresh wound RegenX coil. 108W + 18w (core drag) just like the conventionally wound E-Core.
...

108w + 18w - 40watts - 60watts = +26w
...

No. You forget to add in 160 watts increase with RegenX coil disconnected. So it would be 268W + 18w (core drag). 160 watts is the increase the debunker observed going from a conventional wound coil to bifilar coil. Remember his test? The actual value of increase power may be different, but no reason to believe it won't be significant. You guys always, conveniently, forget that, making your comparisons invalid.

So instead of make-believe numbers, why don't you run a real test with conventional coil against RegenX coil and use real data?
bi

[BroMikey]

Everyone who thinks that they have got something unique have got to present it in a proper way.


All you need to know about the prime mover is rpm and torque period.


John.

Hi John yes that is a good point. here let's look another way. Take a rotor out of the box and throw a set of bearings on it and then set 24 magnets into the rotor. Congratulations you just spent a bunch of money and time. Okay well we won't itemize the task but be sure you get the spacing 100% right on, no mickey mouse (like Bye-Slanders) rotor will replace a machined unit.

Now you are almost there. Next take the head off of a state of the art conventional (MOT) transformer and you have an E-Core with some windings. Start up your rotor and run it at 3500rpm to 5000 rpm, some where in this range is fine. If you are able to do that without being struck by flying magnets (congrat's again) you probably spent enough money on it so it does not self destruct and take you with it.

Now you must record the voltage and amp draw of the little motor driving the rotor. Let's say it is a 36 volt motor that draws 3 amps to make the rotor go with no cores anywhere around it.

Next thing is to bring the transformer E-Core (This is what Thane did) up close to the rotor magnets say 60 thousandths of an inch spacing. Congrat's you put a feeler gauge between all of your magnets (not like slander did) and the rotor is so true that every magnet around the entire rotor has a 1/6th inch gap.

.060-.062" is nice. Just to bring the core up to the rotor magnets costs you some drag. Now your meter is reading 36 volts at 3.5amps. You are about to generate some power.

Next using the low voltage side (Not the 5000v winding) connect a 12v light bulb. It only will produce about 6v and the bulb will be dimly lit. Not a very good test but it works. You are going to need a better coil to raise up the voltage if you want 50-100 volts But for now let's use this one. The car headlight bulb can draw3-5 amps 12v or even 15volts but yours is dimly lit coming in at 6v at 1/2amp. Now you are generating 3 watts. Not very impressive is it?

Nope not very impressive like all the fancy torque machines and the latest fluke meters calibrated to high accuracy. While you are thinking about my measly 3 watts and how cool your dynamometer is I am winding a fresh coil of magnet-wire. Oh yeah my 3amp draw went to 3.5amps a 18watt increase just on core drag and the generated power is only a 3 watt drag.

So here is what we have. 36v X 3A = 108w for just the rotor no cores

Then an additional 1/2A core drag or 36V X 500ma = 18w

It is time to generate at 6v X 500ma = 3w

Now the blind people all laugh because they don't see where this is going.

We have 108w + 18w + 3w = 129w

Next do the same thing with a fresh wound RegenX coil. 108W + 18w (core drag) just like the conventionally wound E-Core. Now comes the 60watt Regenerative acceleration generator output. The cores were already the additional 18w as we said. But now we are getting 60watts from the new coil.

Before we would have had a number like this:
108w (rotor) + 18w (core drag) + 60watts = 186w regular coils

Same every but 1 sixty watt RegenX coil. Now the figures read like this:

108w + 18w - 40watts - 60watts = +26w

The 40watts came when the coil was engaged which means the coil has been wound in such a way that it offers electrical watts (60w) plus it also lowers the drive input by 40watts.

This is for 1 coil. Now add 1 more and you have the so called free energy

[bistander]

... Where is your bullet point? ...

I given a ton of bullet points. Not a single coherent response from you. This last one was claim of battery charging with too low voltage and incorrect current direction.

1000's of hours of teaching lies and falsehoods from Thane Heinz and Turion is all a sham. It does more harm than good. They need to prove their claims with straightforward power out / power in. That is so easy, but never happens.

You said "Dave is not mentally ill anymore than Thane is crazy."

Actually you're right. Both have serious mental issues. They can not see truth and fact which is right in front of them. They are consumed by fantasy of their own making.

Sure, you can wind a coil such that the actual load lessens as the apparent load increases due to internal reactance and signal frequency which results in a decrease in prime mover load (increased motor speed and decreased motor current). But that in no way contributes to extra power output. Same with other schemes. Yes, you can mitigate cogging. So what? Cogging is not a loss mechanism so is irrelevant at speed.

Thane Heinz has 14 years at it, you say. Certainly time enough to run his contraption for a few days continuously and prove it doesn't deplete the battery. Turion had at least a year and a half to prepare for Aaron's conference and prove his claim of OU/FE. His friend tells us that he can't handle the truth. Neither of these guys can face reality.

bi

[Quantum_well]

Everyone who thinks that they have got something unique have got to present it in a proper way. It's the inability of them to use the correct tools and use them properly. Everyone is lead up the garden path by inaccurate measurement. They waste a fortune on lamps,switches, meters and what have you.Ask bistander if it's possible to do an accurate assessment of a generator using volts and amps of the prime mover, if he approves of this method I'll eat my hat!
All you need to know about the prime mover is rpm and torque period.
John.

[BroMikey]

On a serious note, I have no evidence that Dave was lacking in his ways.

. Thanks to Nick, I found a great source for core/bobbin pairs in a bypass choke for audio. I will strip and rewind with #24 wire for better voltage output.
.
I still want to see where that build goes.
thay

There are a dump load of great guys working in the background who may have gotten together to make this more improved machine for sale.Like the black beauty box, that was another man's creation. Then the new cores have put the box in a new light. No heat and more power. Well I have said enough. Stay frosty and don't take any wooden nickels.

[BroMikey]

Bro', it's just all rubbish,..and that's just plain silly.
sincerely John.

You were warned. You didn't say anything John. I want to know HOW it is wrong in your mind. If you are talking about how embarrassingly simple the discovery we need to remember that. Oh and that we all missed it as simple as it was. You will have to be more specific. As i said you can't rebut with a burp or grunt, it needs to be shown. Thane has 1000's of hours of work on the table and many hours of explanation. Where is your bullet point? You must have a bone of contention? Show us. The one liner is cute but adolescent.

See Thaelin, he verified some portion of the effect. Well John we look foreword to seeing your device. See bye-slammer and his weak attempt, at least he tried.even if it wasn't very hard or worth much making a show of it. How about it John? You gonna make a show?You will need a chaulk board, a pointer and have some hardware on hand that relates to the subject for starters.

[thaelin]

On a serious note, I have no evidence that Dave was lacking in his ways. I have had a great interest in the build he was doing. I, in fact, used one of his techniques in the build that I am now finishing. It dropped all the drag on the rotor which was daunting. Nick's build at ESTC did have serious rotor lock to deal with. I did ask to witness it and he agreed. It did take a healthy spin to get it going from stop state. I will have either one more or one less magnets than coils in this build. Thanks to Nick, I found a great source for core/bobbin pairs in a bypass choke for audio. I will strip and rewind with #24 wire for better voltage output.
I can only hope he is well and ok. We just had a person out of work for over a month with the new crap. He is bad off. Sure hope he didn't get that crap too. I wouldn't want my enemies to have it. Dave, you are always open to chat with me private if you wish. I still want to see where that build goes.
thay

[thaelin]

That is a real OU harvest, green thumb hey?

All that would do for me is give a large output of gas. Not the kind I want too>

[Quantum_well]

Bro', it's just all rubbish, the only ones to benefit from "free energy " are those who supply parts to the idiots. Talk of beating Lens is the equivalent of a game of cricket where the ball isn't allowed to contact the bat.....and that's just plain silly.
sincerely John.

[BroMikey]

This is what Dave was doing (Turion) spending huge sums of money that others took advantage of and since have turned against him as foolish as that is.

Dave is not mentally ill anymore than Thane is crazy. Thanks for sharing what you feel because now I know what kind of creatures lurk here. Thane teaches and the rest steal when they should be buying.

14 years of instructional video's showing an open hand to people who live in darkness. Dave the same. Going out of their way day after day, years on end, thousands of hours of free instruction only to be met with people who bite and back stab. Ya know the one liner guys who see a demo that represents 200 hours of a persons time and energy, their only response is equivalent to a worthless grunt while they feel is a qualifying counter. Then there are the yuppies and suck ups who tag along like the lapdogs do.

.................................................. ................

[BroMikey]

My take on OU. IMG_20210721_191818.jpg

That is a real OU harvest, green thumb hey?

[Quantum_well]

My take on OU. IMG_20210721_191818.jpg

[Quantum_well]

• IMG_20210721_192305.jpg

[Quantum_well]

IMG_20210721_192324.jpg

[BroMikey]

Bro' I bet you couldn't give me one working example from the dozens of people who've got working OU. that actually works.

https://raypeatforum.com/community/t...ernment.41532/

This is what Doctors are reporting in California

VAERS Whistleblower: “45,000 Dead From Covid-19 Vaccines Within 3 Days of Vaccination”, Sparks Lawsuit Against Federal Government

The lawsuit was filed by Renz and his legal team alongside America’s Frontline Doctors against the Emergency Use Authorisation (EUA) of the Covid-19 vaccines, which they state have had “no long-term studies on the impact on adults, much less children.”

Also Canada has armored trucks lining up to force the Vaccine because people don't want it.