Bedini Solid State Oscillators

[totoalas]

LAN Cable SS SSG - No resonance 240312

Hi to all

Using a 4 pair LAN cable, no resonance on my crt toroid either its loose or the wires too thin input 12 . 30 output 12.04 even I increase the current fromm 200 to 2 Amps.... need to go back to magnet wire

From another area I was able to raise the voltage from a converted ALUMINUM battery 70 AH from 12.20 standing voltage now is 13.4 v dc with aluminum electrolyte

Win some loose some

totoalas

[ZeropointEnergy]

Mods

SS SSG multiple spke per on time.divx - YouTube

Hey Patrick,

I have a 5k 50W rheostat on order since the 5W potentiometer does heat up when I'm pushing double that through it
I have played around with a few different variables of resistance and capacitance to the base of the transistor to control on/off time, more experimentation is needed. (I'm using leads to clip on the mods to the trigger circuit in parallel)

I had not used a trigger as large as 18 gauge but will order a large roll to give a new 7 transistor SS SSG circuit a 100% effort, with the CPD mod and 2W or larger resistors. My aim is simple, eliminate all heat while fully saturating the coil.
In the past 2 SS SSG circuit I have heat in the coil or pot that needs to be rectified, larger gauge output leads has eliminated most of the issue in the smaller builds, pushing 1-2A @ 12-24V is going to a new senario.

Then can build a voltage regulator circuit/cap bank combo to hook up to a solar panel in place of the primary. Thus far, battery to battery is more efficient

Regards
Zero

[minoly]

Just an update, first trial run on the 4T SS SSG, with a 5 filar Aluminum Magnet Wire coil, no core. In this build i added a "coil sniffer" wind to the standard Air Core transformer. It was wound on with 30 AWG, 21-22 turns, then taped, and the letz'd 5 filar on top. Worked out pretty close to plan (hopes). The filar ended up being about 148 turns, the wires were 100' in length, equal trigger gauge. Thanks for the help, 49'er, Blackchisel and all, all of your tips helped a lot, she fired up first try, this time.

No big conlcusions on the aluminum wire, other than it works, it was cheap, and the savings more than paid for all of the other components of the build. As 49'er had pointed out (but unfortunately I had bought it already... might have been better to buy a bigger gauge, slightly.. say 16 or 14 AWG, to negate higher resistance factors). It's all an experiment!

SSG Aluminum Air Core Experiment PT. 3 - YouTube

IMHO the higher resistance w/o a core is preferable - this is what I find most interesting about your build
I think your charger will outdo mine.
put a large FLAB bank on the charging side.
were did you get your wire?
Thanks,
Patrick

[kcarring]

Aluminum Magnet Wire Air Core Experiment

Just an update, first trial run on the 4T SS SSG, with a 5 filar Aluminum Magnet Wire coil, no core. In this build i added a "coil sniffer" wind to the standard Air Core transformer. It was wound on with 30 AWG, 21-22 turns, then taped, and the letz'd 5 filar on top. Worked out pretty close to plan (hopes). The filar ended up being about 148 turns, the wires were 100' in length, equal trigger gauge. Thanks for the help, 49'er, Blackchisel and all, all of your tips helped a lot, she fired up first try, this time.

No big conlcusions on the aluminum wire, other than it works, it was cheap, and the savings more than paid for all of the other components of the build. As 49'er had pointed out (but unfortunately I had bought it already... might have been better to buy a bigger gauge, slightly.. say 16 or 14 AWG, to negate higher resistance factors). It's all an experiment!

SSG Aluminum Air Core Experiment PT. 3 - YouTube

[mklimesh]

Hi Patrick,
I think that what you show with multiple spikes then a rest period, repeated over and over like you show is a very efficient way to charge a battery. The way you do it is way slicker than how I have been doing it. I've been using a seperate timer circuit to gate it on and off, I'll have to try your setup. Have you put a scope on JB's "10 Amp 12V Battery Charger (AC Power Input)" ? (+_+)

Mike Klimesh

SS SSG multiple spke per on time.divx - YouTube

Patrick

[minoly]

SS SSG multiple spke per on time.divx - YouTube

[Guruji]

SS

OU or not OU ????? the circuit is charging back source battery @ Zero

Ampsrofl:

Important is IT WORKS LOL

totoalas

Super SSG Self Charging @ ZERO AMPS - imtotob 170312 - YouTube

How is the schematic exactly cause I cannot understand what you guys did here?
Did you charge a cap from an SS and then running the SS with the cap?
Thanks

[tturner]

Help with bedini ssg

I am trying to replicate something. It was recomended mechanical ocsilator. money is tight right now so trying to keep costs down. I have been following Bedini Motor ( Generator ) How To Build One - YouTube

what I am wonder is how to wind the coil (bifiliar or pancake?)

Do I need seperate size wire

can I use ceramic magnents

how many coils do I need

cann I use anywire size

Can the wire be with the insulation on the wire when wound

[tturner]

help with bedini ssg

Wondering how to wind the coil
What kind of wire can I use what has to happen

[kcarring]

Aluminum Magnet Wire Air Core Experiment

I've been doing an experiment with aluminum wire. Haven't fired her up yet, but this is what I got so far. Still uploading is this video of what's going on in this experiment.

Cheers

[totoalas]

Hey Totoalas,

I will have to check that out on the "joule ringer" thread. Did you try that on a few parallel AA batteries, that should be noticable

Regards
Zero

Hi Zero

Good point on parallel source

will try tomorrow

thanks

totoalas

[ZeropointEnergy]

JT x SS SSG circuit?

Hi Tyson
from your previous drawing of minoly mod 6 coiler now to his 2nd mod 4 transistor using only 5 coiler the extra coil connected to a toroid with ring magnet bet the 5 coiler and toroid then to a diode and goes back to the source battery
from initial 9.4 v standing voltage it went to 11.20 after 6 h
hours see my sketch in joule ringer same set up

thanks

totoalas

Hey Totoalas,

I will have to check that out on the "joule ringer" thread. Did you try that on a few parallel AA batteries, that should be noticable

Regards
Zero

[ZeropointEnergy]

Thanks Zero
thats the way I experienced it with the ssg SS SSG 101

lesson 3 Never remove the load when the source is still connected or youll burn the transistors


totoalas

If you add the neon to the CE of the transistor you can safely remove the load for at least 5-10min intervals. I do this all the time when showing people the SSG can generate 200-400V (depending on the build) off 12V input and is not wound like a transformer Also, how you can see and hear the radiant pulses generated in the neons.
I have done this many times with no damage to the transistors, but do that with heavily sulfated batteries and nothing can save the transistor

I'm still learning everyday with all the different tech I experiment with

Regards
Zero

[totoalas]

Hi folks, Hi totoalas, I'm not sure what you are showing in the video, though it looks like you might be filling a capacitor in some way (radiant charger), then charging the source battery again with the capacitor powering the radiant charger, though this time no amperage is obviously taken from source because it is being recharged.
Is this what you are showing, thanks.
peace love light
tyson

Hi Tyson
from your previous drawing of minoly mod 6 coiler now to his 2nd mod 4 transistor using only 5 coiler the extra coil connected to a toroid with ring magnet bet the 5 coiler and toroid then to a diode and goes back to the source battery
from initial 9.4 v standing voltage it went to 11.20 after 6 h
hours see my sketch in joule ringer same set up

thanks

totoalas

[SkyWatcher]

Hi folks, Hi totoalas, I'm not sure what you are showing in the video, though it looks like you might be filling a capacitor in some way (radiant charger), then charging the source battery again with the capacitor powering the radiant charger, though this time no amperage is obviously taken from source because it is being recharged.
Is this what you are showing, thanks.
peace love light
tyson