Imhotep's Radiant Oscillator Video

[Inquorate]

@ gotoluc

Can you post a schematic of your lc oscillator circuit? I've been trying to make a colpitts oscillator / signal generator for when I get vacuum tubes (to switch coils instead of trannies which get soggy in my opinion) BUT nothing I make works. Except one, which would oscillate for about a second. I've got 2 variable 60 to 160 puffs and 50 k pots and rf resistor... Only other option I can think of is I found info on a type of tube which is specifically made to oscillate, and another type appears to be made as a cut-off diode... Also looked into crystals but their circuits are too steep a learning curve for me; I can't visualize what's happening.

/// to all: made my move to under the house!!! Also found someone on this thread who works near where I live, so we'll probably get together for a think tank. So I'm extending an invite to all to take a peek at my lab...

YouTube - Inquorate 15

Cheers

[nat1971a]

YouTube - Tesla Wireless Transmission with Aromaz circuit - Video 24

Wireless transmission with Aromaz circuit

[Aromaz]

..... Please do not get me wrong, this is not a criticism and defiantly not a replication of your circuit.......

Luc, I am not in this for myself and my self ego is solid enough. I do consider criticism very valuable here. Neither did I try to defend my system nor suggestions. I am seriously trying to get to the botom of this.

If that was not my wish, I am sure I could use this circuit and all I have shown in the video's rather to get or scam BIG money from someone ignorant. Thus, it is here and hopefully we all can work together to make it workable for the people of the world. Later on we can figure out how to use this in modified form to make profitable products.

Is this right, good and valid -
A: IF YES, then lets fine tune it and release it to the world. Note my word 'release'. I doubt seriously that I would go into production of this kit.
B: IF NO, then lets forget about it and go on searching for the valid one.

[Lidmotor]

Corrie's wire wrapped tube

I built and tested parts today. I now have the spark gap device and the wire wrapped flourescent tube. What I am missing are some transistors which I hope to get soon. The shortened circuit that I am now using is probably why I am still drawing too many amps but I'm hooked on it because it seem to be bullet proof and it makes GREAT BIG sparks. Even my wife thought that it looked pretty cool today and she doesn't care for most of this stuff.
I am trying to correlate what I am seeing to what I am learning from everybody here and the info on the web. The more that I learn the more that I want to know. Tesla facinates me. I started looking at pigeons a little different today. Mart where do I get the feed?
Here is the video of the new parts:

YouTube - Tesla High Voltage Display

Lidmotor

[gotoluc]

Thanks for the quick reply Corrie,

well, I did not say above 20khz but around this range. Point being that analogue meters are not reliable at these frequencies. I tried it with an analogue meter and found out it was not displaying correctly. To check it I placed a low amp 12v bulb in series on the positive lead from the battery. If the bulb lights or glows it is an indication amps are flowing that's when I noticed that as I changed pulse frequency the meter was not following the bulb intensity changes. So I connected my good quality digital meter and it was only on the AC amp setting that it was following the bulb intensity correctly.

Please do not get me wrong, this is not a criticism and defiantly not a replication of your circuit. I am only pulsing a primary of a coil using a 12v battery, switch by one mofset triggered by a signal generator and observing the effects at various frequencies with different capacitor value in parallel with the primary (LC circuit) to see if I can get it to resonate. That is when I noticed the above.

Thank you for your most excellent work and looking forward to hopefully soon replicate your work

Thank you for sharing.

Luc

[Aromaz]

AC or Ping-Pong ?

...........This DC pulsing is also why an analogue meter will not work as we are pulsing the coil in the 20khz range and they cannot display a correct reading at this frequency due to the analogue needle coil frequency limit........

[Aromaz]

Wondering Old man

actually the ground is more a aluminum strap...quite thick...about 3 feet long

Earth Power vs Grit power leakage vs Communications signal power?

[gotoluc]

Thank you Corrie for the great detailed photos and parts information

I really appreciate all the work you have put into this.

@everyone,

I just completed some basic tests. The tests was to only try to get a coil primary to resonance and observe the effects. One thing I found that would be important is if you use a Analogue Meter it will give a false reading and if you use a digital meter you will need to set it to AC.
Even though your source battery is DC the transistor is pulsing the DC through your meter and you will get a false reading if you use it on the DC amp. mode. This DC pulsing is also why an analogue meter will not work as we are pulsing the coil in the 20khz range and they cannot display a correct reading at this frequency due to the analogue needle coil frequency limit.

Please accept my apology if all of you know this. I'm just trying to make sure we are all on the same page on the way we measure amps.

Thank you for all your great work and sharing

Luc

[Aromaz]

Greeting. Yes, it is sort of wireless transmission. It is wireless in the sense that no metallic wire is involved, but it is probably not the Tesla version of wireless energy transmission.

I agree 100% with you. It is not in the line of scalar waves, rather just completely charged environment. Allow an old man to play a bit too?

However, I did learn a few things from this. I did not intend to go 'wireless' it was a by-products. Though since this was first seen on Wednesday I did play a bit more with it - and I expanded the thing quite a bit.

My agreement and offer is:
The first discovery will be completely public, free for everyone. Simple utility which will mostly benefit the less fortunate people on earth. That is the low power economical light - which I am still working on 98% of time. Let there be light!!!! Thus we can see........see.....seeee!

Second discover will be more complicated - and that will be for commercial purposes to cover my expenses and make some profit for my partners/friends/investors. Presently I think it will be the wireless transfer -which in fact is substantial different from Tesla.

Then # 3 will be public release again. #4 for personal gain.... all odd numbers is free public domain, all even numbers are personal gain.

Folks, there is one thing that puzzles me a bit. PLAY and get OUT OF THE BOX.

[Aromaz]

More photos

Below more photos to continue from previous.

Today (I hope) to change the complete setup. This will take some time.

I want to isolate this whole thing from all other possible interference and see if it will still work. For instance I am going to build a test box (Faraday cage)on a table, all double insullated with foam and wire mesh, and double window to see inside, complete own ground plate. If it works somewhat, then we know ground capacitance and building is not involved. If it does not work, then still easy to connect ground up to plate and also to transport whole set to farm for testing.

[Aromaz]

Setup

OK, here is what I can give you:

I have four coils, 2x No-Name, 2x Hitachi.
Though slight different in resonace, they work nearly the same.
Two coils of same 'make' tested exactly the same. Mass production.
Used in latest video were all the No-Name brand.
When 2x coils, they are the same pair.

Set #1 = No-Name (on left)
+ to - = 1.92 Ohm
+ to HV = 10.42 k Ohm
HV to - = 10.42 k Ohm

Set #2 = Hitachi
+ to - = 1.6 Ohm
+ to HV = 8.56 k Ohm
HV to - = 8.56 k Ohm

Attached photos of everything:
KSP2222A -303, 2N3055, setup views

Note: 2222 on left face forward, on right face backwards!

[nat1971a]

actually the ground is more a aluminum strap...quite thick...about 3 feet long

[Jetijs]

Great work Nat
Thank you

[nat1971a]

And the amp meter is virtually brand new...only bought it a couple of months ago

[nat1971a]

All,

If it helps

Heres the parts i am using:-

ST2n3055 x5
33G PN2222A
Sourced from radio parts here in australia

I connected a ground to the base of the 2222A just as aromaz did...Worked first time out of the box...just as per aromaz circuit

The ignition coil is a bosch SU12 sourced from supercheap auto here in australia.

The ground connection is a aluminum plate in the ground....

Very interesting to see the amp meter not register at all!!

Cheers

Nat