Imhotep's Radiant Oscillator Video

[Bodkins]

Hi Gmeat & all

I'm using a Bifilar coil and associated circuit from an experimental SG energsier. It has 19R 0.53mm strands (2 x 500 gram spools of ECW wound on a Pittsfield spool) with an iron core. It works better than everything else I've tried to date and I can run two CFL's at good brightness on 300mA @ 24V.

An earth connection does improve brightness on my setup. The trigger circuit is around 2K ohms for best brightness. I can find a point where I run at approx 10KHz which is the most efficient setting. Everything becomes very resonant and sensitive.

The light ouput from the CFL's is very thermally and visually cold / white in comparison with a normal mains driven lamp. I'm not convinced that the light output can be improved on very much when driven from an ignition coil and it seems that everyone so far is getting very similar and fairly low light levels. I did post a scematic of my first attempt using a pulse transformer and Line output transformer but the LOPT subsequently failed. Does anyone know how the heat is produced in a mains driven CFL? I'm asking this in case we can improve brightness by increasing the heat level.

Hoppy

Hi Hoppy
Great stuff i was sure the freq was around there. its the earth freq.
Can you tap the energy from the earth rods?


Gmeat you doing the lightamp test with the rod?
Sounds like your getting just HV.

[Hoppy]

Hi Gmeat & all

I'm using a Bifilar coil and associated circuit from an experimental SG energsier. It has 19R 0.53mm strands (2 x 500 gram spools of ECW wound on a Pittsfield spool) with an iron core. It works better than everything else I've tried to date and I can run two CFL's at good brightness on 300mA @ 24V.

An earth connection does improve brightness on my setup. The trigger circuit is around 2K ohms for best brightness. I can find a point where I run at approx 10KHz which is the most efficient setting. Everything becomes very resonant and sensitive.

The light ouput from the CFL's is very thermally and visually cold / white in comparison with a normal mains driven lamp. I'm not convinced that the light output can be improved on very much when driven from an ignition coil and it seems that everyone so far is getting very similar and fairly low light levels. I did post a scematic of my first attempt using a pulse transformer and Line output transformer but the LOPT subsequently failed. Does anyone know how the heat is produced in a mains driven CFL? I'm asking this in case we can improve brightness by increasing the heat level.

Hoppy

[gmeat]

Has anyone tried a bifilar yet!

Hi Everybody,


Has anyone tried a bifilar on the trigger side of the circuit yet?.I have a bifilar coil with #23 awg and # 20 awg about 400' in length with a magnetite core and when I run my SSG with this coil it produces multiple pulses with each magnet passing by and can get about 8 to 10 pulses depending on which guage wire I use.Well,I figured I'd give this core a shot at the Imhotep/Lidmotor/Bodkins/Theremart/Whoever else I failed to mention running the CFL's.The bottom of my trigger coil comes through a 5k pot then my coil then a 25ohm pot then a base resistance of 47 ohms.When I tried to get it to self oscillate hooking the coil up normally using the #23 or #20 guage wire it didn't work,But if I hook it up to the #23 at one end and # 20 at the other end Bingo it starts right up and will work with either combination of wire guage as long as it's two different guages of wire (I'm not sure why it works but it does).I can replicate Bodkins affect of charging up a cap(560Uf 200v) hooked up to an earth ground and it directly relates to base resistance,Another words if I have the amps set at around 70 milliamps The cap will stop charging up at around 60-70 volts,And if set higher to around 200 milliamps or above the cap goes to max rating of 200 volts.I have also come accross the strange affect that I can charge a dead battery but cant charge a good battery .The latest thing I'm working on is to see why and if I can extact something off my coil that I'm getting a reading of 199+ volts on the meters AC scale connected accross the coil while running at 490 milliamps.Thx to all for the input.


-Gary

[Bodkins]

glowman: !!!

Lot's of people don't sleep here and we seem to forget our age. or...time !

and thanks for the link.

nat1971a: congratulation for your successful replication. don't forget to sleep !

Lidmotor: your "grounding rod" is what surprised me, considering its form and length. Sometimes i think about the alkalinity/acidity of the ground and the percentage of moisture.

anyway, we are all thinking.

Good work everyone!

I have had 6hours sleep in 48

[Agongon]

glowman: !!!

Lot's of people don't sleep here and we seem to forget our age. or...time !

and thanks for the link.

nat1971a: congratulation for your successful replication. don't forget to sleep !

Lidmotor: your "grounding rod" is what surprised me, considering its form and length. Sometimes i think about the alkalinity/acidity of the ground and the percentage of moisture.

anyway, we are all thinking.

Good work everyone!

[Bodkins]

Good work Bodkins. The ground rods are going to be different for everyone, as each of them will exhibit different levels of capacitance I think. Confirms what AC was talking about before That cap is charging up pretty fast, need to think of a way to dump it somewhere now


Oh and in regards to my previous post, OPTO ISOLATOR (h11d1)

the cap keeps going up and up and up 200v i stop it. AC Was Spot on
if not in tune it stops at some point. because of the limited push of the positive from the ignition coil hv.
Roxaz find a computer. watch it and smile!!!!!
Byjove cheers for sending people on the path!
Glowman think about ignition packs.

Can anyone talk to Drevtoobe on you tube he thinks that he can explain the effect!!
i dont agree!!

[roxaz]

YouTube - Way Forward

could anyone comment this video? I cant rly watch it cause i access internet on my cell =]

[ren]

Good work Bodkins. The ground rods are going to be different for everyone, as each of them will exhibit different levels of capacitance I think. Confirms what AC was talking about before That cap is charging up pretty fast, need to think of a way to dump it somewhere now


Oh and in regards to my previous post, OPTO ISOLATOR (h11d1)

[Bodkins]

YouTube - Way Forward

[Bodkins]

Lid this is where the knowledge from the cap pulser can be implemented! Frying 555's? Probably because your 555 is directly connected to the source/ignition coil. Hmmmm.....how did JB get around that on his schematic

Bridge rectifier REN?

[ren]

Lid this is where the knowledge from the cap pulser can be implemented! Frying 555's? Probably because your 555 is directly connected to the source/ignition coil. Hmmmm.....how did JB get around that on his schematic

[Lidmotor]

Smoking circuits!!!

Wow. I just smoked my circuit making lightning @ 36 v. Lots of fun till it popped. Mini plasma cutter

Ren,
Don't feel bad I did the 555 circuit today thay was posted above and fried 2 nice 555 chips. I got it to work but messed it up by trying to get the earth ground hooked up. Amp draw was too high also and I don't know why.

Congratulations to everybody who is working on this project. I'm sure that Imhotep, Peter, and Tesla approve of the effort.

I'm about to start a new thread called " Rubber glove phenomenon" Everybody watch your fingers!!

Cheers--

Lidmotor

[ren]

Wow. I just smoked my circuit making lightning @ 36 v. Lots of fun till it popped. Mini plasma cutter

[theremart]

Neat trick I found tonight

Put a neo magnet on the fan, and slowly turn the fan you can tune it like the relay


Rubber gloves are my friend with this circuit.

[nat1971a]

YouTube - BEDINI IMHOTEP BODKINS REPLICATION UPDATE

Replication update

@YES i am not using the water pipes now....

@YES i want to light up the world or at least my house

@YES great work team.