Free Energy At Last Step By Step Must See

[Joit]

Zooty, you are soo smart,
but actually, i only wait, that you answer the Questions above,
and a Proof, that you charge up a 7,5Ah Batt with THIS Kind of Fan,
nothing else, what eat 250mA,

And even that is Way to high Input, what you did build there.

Maybe you should first 'Think, before you open your Mouth'

Seriously, i dont know, Peoples come in here, wanna learn,
but think, they do know all and anything better.

[Zooty]

First of all Joit, the device you have would not have been possible if it wasn't for Bedini's work. You have an SSG circuit with a fan as the magneto. The "Story from a Book" was written by the man who made it possible for you to blindly build the device you have. I have built a few of these and they can charge a 18ah battery in 12 hours using just 250ma@12v with #24 wire. If you don't know what is charging the battery then you haven't been paying attention. If your device wont charge the battery properly then you haven't built it properly. Put a 1ohm resistor across the output (on a working device) and that will show you that it is not conventional electricity charging your battery. I have read the book many times to further understand what is happening, that is why my device works properly and yours doesn't. Think before you start shooting your mouth off at people. This post is nothing against you, but you did discredited the very people who made this possible for you.

[Joit]

Lost66
You better seperate the Coils into 2x2,
like Imhotep did show it at his Circuit and his Videos.
When you trigger all 4 Coils at the same time,
the N-S Fields at the Magnet will cancel each other out.

Btw, what is your resistance at your Coils, it should be higher at last, as the Resistance at the Gate.
Ie, coils 10 Ohms, or 5 Ohms,
and Pot or Resistor for the Gate minimum the same or lower.

[Joit]

@Joit, If you think what is coming from your thin wires is power then you will never understand the concept. It is the rise and fall sharpness of the high voltage/low current that resonates your charging battery in the vacuum which makes it charge itself. The key to getting this stuff to work is understanding what is happening at a much lower lever in the system. I would recommend Bedini/Bearden's "Free Energy Generation" book, it explains it very well.

Lol Zooty, thanks for remind me on that.
But what i did wrote above is a practical Experience,
not a Story from a Book, or something, what i did dream about once.
Hows about, YOU show us, how you charge a 7,5Ah Batterie in 12 Hours
with a Fan from a computer, what has only #35 Wire inside.

And further, explain, what you do think, how it gets charged,
and please, without pointing at a Book, what you did read once.
And btw, your Answer is still not correct too, actually, Way beside the Track.

Sometimes, it sounds like, for some is the Word Energy from the Vacuum like a Drug,
that some allways need to use for all Explantations.
And well, you maybe wanna explain that too, what you do understand
at the Term Energy from the Vacuum.

-Edit-
And at last, explain me, where or why do you think, YOU know, what i think.

[blackchisel97]

Look at post 155

[ATTACH]3994[/ATTACH]
hi i found this 2 b very interesting, and have attempted 2 get it going. but with no luck. wt did i do wrong!?

http://www.energeticforum.com/renewa...ust-see-6.html Post 155 If that is the circuit you're trying to build.


Vtech

[Zooty]

@Joit, If you think what is coming from your thin wires is power then you will never understand the concept. It is the rise and fall sharpness of the high voltage/low current that resonates your charging battery in the vacuum which makes it charge itself. The key to getting this stuff to work is understanding what is happening at a much lower lever in the system. I would recommend Bedini/Bearden's "Free Energy Generation" book, it explains it very well.

[lost66]

man has tryed and failed, but never failed to try!


hi i found this 2 b very interesting, and have attempted 2 get it going. but with no luck. wt did i do wrong!?

[lost66]

[IMG]My Computer\Nokia N97\Mass memory\Images\Camera\200910\200910A0[/IMG]

[Joit]

Well, i guess, its not 'Free Energie' right now,
and that is, what other say, that J.B did never claim it, that the SG(Schoolgirlmotor) is.
What i know, the Ratio should be 1:1,7 what you can charge, its not much, but i did not do a compare with 2 same Batteries, where i really can confirm it.
And other Thing, this small Fans dont have thick Wires inside,
dont assume, they spit much Power out, but they are nice, to make high Voltage.
There are plenty of Variations of it, and i prefer anyway more, to make my own Coils.
And this is good, for charging up any batteries, and get more Capacity in them, what much dont see.
Even that is a good Reason for need to have one.

[Mapmann]

mindmaster switch the ends of one coil, then it should work. At Plus and Collector ie.

For charging a 4 Amps battery you maybe wanna use thicker wires as #30

just change the Coils Oo i hade this Problems 3 Times and buy 3 New Motors xD okay i think i the next Holidays i try my best second Time to build "free Energy" ^^

[Joit]

You have actually 2 Coils at your System, each Coil has a Start and a End wire.

One Coil is connected to the Collector of the Transistor and the Plus.
The second Coil is Connected to Minus and Emitter, with the other End from this 2nd Coil to the Potentiometer and the Base of the Transistor.

Swap the Wires from one of this both Coils. Its all described a bit earlier in this Thread too.
The Problem is, that one Coil dont get the Signal right.
The Transitor opens, when it dont repells the Rotor.

[mindmaster]

sorry im a bit of a noob what do you main with swith one end of the coil.
thenkx

[Joit]

mindmaster switch the ends of one coil, then it should work. At Plus and Collector ie.

For charging a 4 Amps battery you maybe wanna use thicker wires as #30

[mindmaster]

rotor

If I put in the power the rotor moves a bit and then you feel that the magnet hangs but does not do anithing what am I doing wrong can someone might help me thenkx

[franzink]

help

I tried to use the bedini imhotep fan and it charges a 5 year old 12V 4AH battery and a 6V 4AH battery but they seems to charge up to 12.30+ volts and when i use it it dies very quickly

My bedini is connected to a DC Voltage regulator 3A and 12Volts.

I also tried to charge a 45Ah Car Battery and a 50Ah battery both of them are defective which i bought it at a Auto Supply Shop and tried to charge them for 2 days non stop but still does not charge well

How do you know its fully charged? im using a voltmeter to check

I tried to run the bedini fan at 24V but the 2N3055 gets very hot and after a while it does not work anymor, but when running it at 24V it charges very fast.

Should i connect the 2n3055 transistor a heatsink and try to run it at 24 volts?

Maybe i should buy the Radiant Charger instead?