How to build a water coil

[MonsieurM]

FYI:

I posted this earlier:

Water Vortex Magnetizer and ORMUS M-State Concentrator
(not sure about the following statement but probably some have used it)

This is the "Original" structured water device that is
used by "Joe Cell" and "Moe-Joe Cell" inventors
to create highly energized water for their hydrogen cells.

Wouldn't you think there is a correlation between "Joe Cell" and "Moe-Joe Cell" and Peter DAVEY Sonic Resonance Boiler

The design of the Davey's sonic heater is extremely simple. It actually is composed of two major parts only - see Figure K8 (3) from monograph [1/4]. The most important out of these two parts is a resonating hemispherical bowl (1) made of a sound inducing metal plate. The second part is a buffering hemispherical bowl (2) almost identical in shape to the bowl (1). This second bowl has the radius around 4 mm larger than the resonating hemispherical bowl (1). Both bowls are assembled symmetrically one around the other, means the hemispherical bowl (1) is placed inside of the hemispherical bowl (2). Coin is 32 mm wide = 1.25984 inches / Big bowl approximately 1.75 inches wide and .75 inches thick / Small bowl approximately 1 3/8 inches wide. Of course, apart from these two bowls, the heater also includes a long rod, nuts, washers, and electrical wires. These are to hold it together, to supply electricity to both bowls, and to allow the heater to be submerged into water that it heats. But these other parts are marginal additions only. The major parts are the bowls. During experimental production of this heater, the resonating hemispherical bowl (1) usually is made from an old cover for a bicycle bell. The dimensions of this hemispherical bowl are not important. It is only vital that it falls into a sonic resonance at the frequency of 50 Hertz, and that it has the outer surface which is parallel and equidistant from the external buffering hemispherical bowl (2). To each of these two bowls a different wire of the household electricity supply (i.e. 220 V, 50 Hz) is connected. The heater must be submerged in water that it heat. It brings water to the boiling point extremely fast. More details about the design and operation of this sonic heater is provided in subsection K3.3 from volume 10 of monograph [1/4]. After being constructed, the Davey's telekinetic heater must be "tuned" in two different manners. The first tuning depends on providing the hemispherical bowl (1) with such frequency of the own oscillations, that makes this bowl to resonate acoustically when a sound of the frequency 50 Hertz is emitted nearby. The second tuning of the heater depends on appropriate selecting the distance "L" between both bowls (1) and (2). On this distance depends the formation of the standing wave between both bowls. Thus it decides about the energy efficiency of the entire heater. From the information that the inventor repeated to me, I gather that the measurements carried out by New Zealand scientists suggested that this heater may consume even less than the equivalent for around 5% of the energy that it generates in form of heat. This would indicate, that the electrical efficiency of this heater is around 2000%.

I also carried out a simple analysis of 3 kinds of water from the same tap for 2 parameters: - pH and conductivity. The results:
(1) The bottle with raw water: pH = 7.54; 497 µS (mikrosiemens).
(2) The bottle with water boiled traditionally for 5 minutes: pH = 9.21; 300 µS.
(3) The bottle with water telekinetised for 5 minutes: pH = 8.68; 302 µS.
Conclusions: in telekinetised water something decreases its pH to 8.7 and does NOT allow it to rise to 9.2 as in water boiled traditionally. So further research is needed to establish what it is.

Shocking history of the revolutionary boiler which bits all possible records (in English) (2/3 down the page to see the replications)






could not find replication vid online of this set up, but well worth trying to replicate just to efficiently heat your water (you could use gold, silver, copper etc... to give your water new properties... ) or boil it and put it in a moe joe cell (takes a few sec to get it to boil)

http://www.energeticforum.com/renewa...ey-heater.html

Peter Davey -- Sonic Resonance Boiler

YouTube - ‪Peter Davey's Sonic Resonance Boiler - 02.2008‬‏


ps: check out the vid i posted

http://www.energeticforum.com/144062-post103.html

[sucahyo]

We do use quartz to run our watches, why not use other type of crystal to help tune a water coil

Transistor and diode are crystal.

Joe-Cell or moe-joe cell can produce voltage but not heat. Fuelless operation also show how some fuel is generated without consuming anything. I think they are not the same as Peter Davey heater. The heater consume electricity and obtain extreme efficiency trough resonance. Joe cell do not consume anything so efficiency can not be calculated.

[MonsieurM]

Transistor and diode are crystal.

Joe-Cell or moe-joe cell can produce voltage but not heat. Fuelless operation also show how some fuel is generated without consuming anything. I think they are not the same as Peter Davey heater. The heater consume electricity and obtain extreme efficiency trough resonance. Joe cell do not consume anything so efficiency can not be calculated.

Thank you sucahyo for correcting me , what i meant by "correlation" is in the structure being used not how they are used, i think that both use resonance to be functional (we are looking here at the cause not the effect ).

moe-joe-cell



Official Website of The Moe-Joe Cell Spherical 316 Non-Magnetic Stainless Steel Joe Cell


sonic boiler:

[MonsieurM]

Returning to our current topic: How to build a water coil research:

I have found some quite interesting info, about the use of coils in Homeopathy

first a review of the various coils I have showed you so far:




Homeopathy – How It Works and How It Is Done

Chapter 5 Methods of Potentisation There are many ways of preparing a homeopathic potency. This chapter will attempt to unify and to relate all of them to the physics of water. 5.1 Potency Resolution Resolved In Chapter 4, I concluded Section 4.3 with the remark that, “To measure the bandwidth of a water imprint would require an [...]
...The information in a homeopathic potency can slowly imprint into water by contact without need for any mechanical succussion. As an example, a glass tube containing ‘erased’ water (see Section 4.6) was placed in a beaker of water imprinted with a range of frequencies. The higher frequencies imprinted more quickly than the lower frequencies as shown in Figure 1. This suggests that the potentisation process does not necessarily require energy other than thermal excitation and that imprinting awaits the random arrival of the correct frequency component in the thermal noise to effect a potentisation.

Figure 3. Interaction between the speed of vortexing and the magnetic field required to potentise.

5.1 Potency Resolution Resolved
In Chapter 4, I concluded Section 4.3 with the remark that, “To measure the bandwidth of a water imprint would require an oscillator with a resolution of better than 2 parts in 107.” Since then, I have had brief access to an oscillator [1] which had a frequency resolution of 1 microHertz. This frequency corresponds to one cycle in 11˝ days and gives access to circadian rhythms. With its maximum frequency of 80 MHz imprinted into water, the resonance was detectable down to 79.999 346 MHz representing a bandwidth of 1,308 Hz. From the equations in Section 4.3, the theoretical bandwidth assuming that the energy of the quantum fluctuations in the number of coherent 80 MHz photons equals the energy of thermal vibrations at 15°C comes to 6,720 Hz. I may only have measured the tip of the iceberg but theory and experiment have reached the same ‘ball-park’.

5.6 Imprinting with A- & B- fields
The electric field (E-field) describes the mechanical force between electric charges, a magnetic field (B-field) arises when these charges are moving at a constant velocity, radiation occurs when the velocity changes. Figure 4 shows four coils in which a current flows in the direction of the arrows due to an electric field applied across the ends of the coil.
The solenoid generates a uniform magnetic field (B-field) within the coil, the lines describing this field pass along the axis and loop around the space outside the coil. Its magnetic field occurs in closed loops and is at right angles to the direction of the current.
The toroid contains the magnetic B-field within the torus. There is no external B-field but, there is an additional quantity called the magnetic vector potential (A-field) which is in the direction of the current and loops around and through the ring. This field can affect the phase of the wave function in a quantum system.
The Caduceus coil is a solenoid counter-wound back on itself so that the B-fields due to each half of the winding cancel. However, the A-fields rotate in opposite directions and generate a plane wave of A-field.
The Möbius coil is a loop with a twist in it so that the current is always in opposite directions in the upper and lower surfaces. Ideally, all the fields should cancel but the currents are only approximately coincident so there still could be a torque-like A-field.
Other arrangements such as a Helical Coil or Antonine Rings give more even complicated fields and effects.

I highly recommend reading the article, it covers a whole range of topic on water and gives us some very valuable data

Homeopathy – How It Works and How It Is Done – 5 | HPATHY.COM

a whole panel of scientific research on homeopathy:

Scientific Research | HPATHY.COM

[MonsieurM]

Within a coherent system, the range of the coherence (coherence length) becomes the constant quantity instead of the velocity. This makes frequency proportional to velocity apparently without restriction, so long as one remains within the coherence length. There can be many velocities each with a proportionate frequency; there can be as many frequencies as there are possible velocities. Frequency no longer has an absolute value, the system has become fractal in frequency.
As a consequence, effects can occur in many different parts of the electromagnetic spectrum all originating from the same source which might be chemical, biological or electromagnetic. It is this which links effects of frequencies characteristic of chemicals to technological frequencies and through to the frequencies of biological systems ( see my post#20 through 22 http://www.energeticforum.com/136257-post20.html ). It is also the reason why environmental frequencies can mimic a chemical exposure for hypersensitive patients carrying a toxic body-load of a matching chemical. Table 1 shows the fractal frequencies generated by imprinting the optical spectrum from a mercury discharge lamp into water.

And it respect the fundamental law of:

the Constructal/Fractal law of nature: (see http://www.energeticforum.com/psychi...tml#post144810 )

The constructal law puts forth the idea that the generation of design (configuration, pattern, geometry) in nature is a physics phenomenon that unites all animate and inanimate systems, and that this phenomenon is covered by the Constructal Law stated by Adrian Bejan in 1996: "For a finite-size (flow) system to persist in time (to live), its configuration must evolve such that it provides easier access to the imposed currents that flow through it[."

Tree frequency measured by Farmhand the system has become fractal in frequency.



------


Homeopathy – How It Works and How It Is Done – 4 | HPATHY.COM

Along the same line:

Plants may be slow but, they are not stupid! – 2 | HPATHY.COM

the system has become fractal in frequency May be the key to all our research, I truly believe this is a major step forward.

so excited that i found this info ....links water in the tree and this research

[MonsieurM]

Another example of the Constructal/Fractal law

The constructal law puts forth the idea that the generation of design (configuration, pattern, geometry) in nature is a physics phenomenon that unites all animate and inanimate systems, and that this phenomenon is covered by the Constructal Law stated by Adrian Bejan in 1996: "For a finite-size (flow) system to persist in time (to live), its configuration must evolve such that it provides easier access to the imposed currents that flow through it[."

where the system has become fractal in frequency.

moe-joe-cell





Official Website of The Moe-Joe Cell Spherical 316 Non-Magnetic Stainless Steel Joe Cell



From Brain Waves to Mathematics of Fractals
- The beauty of numbers behind irregular functions - (ppt presentation)

http://www.nara-wu.ac.jp/initiative-...amura-file.pdf



just search fractal brainwave and you will find a lot of info on this

one essential point is for you guys to think Outside the Box, none of us can truly tell what are scalar waves, they could be as diverse as their are different type of waves in the ocean (ask a surfer )

[MonsieurM]

Computational Modeling of New Kinds of Fractal Antennas and
Fractal Frequency-selective Structures Based on Them

Abstract| Authors' realized modeling of two kinds of fractal antennas with similar structure, but different algorithms of development. The first antenna geometry is a figure "Life Flower" and the second one is series of crossed circles nested to each other. The obtained results were analyzed and conclusion of the practical applicability for these antennas was made. The obtained theoretical results allow us to conclude that synthesized fractal antennas have multi-band and wide-band features. Besides the direct usage, such fractal structures performed on micron-level may reveal an application in a wide class of new fractal frequency-selective materials and surfaces. The applicability sphere of fractal antennas in modern technologies was shown: cellular communication, wireless information transmission and reception, and radar location devices. Also application filed was described for fractal antennas in modern technology: cellular communications, wireless receiving and transmitting information devices, and radar.

http://www.google.com/url?sa=t&sourc...KlN5Rob9nwlwYA

Remember : the collapsible bladder (from http://www.energeticforum.com/144601-post122.html ), it emulates your heart...

the collapsible bladder (it may facilitate the creation/concentration of ORM in water ex:your heart ):

YouTube - ‪Innovative micro hydroelectric turbine‬‏

http://www.energeticforum.com/renewa...c-turbine.html

Though in video water flowing from tap is shown it works same way if there is a reservoir at starting of the collapsible bladder and if small pipe is connected to it.

Clearly the processes of suction and pressure need to be examined.[ No beneficial, natural exchange can take place solely under conditions of pressure. . Viktor Schauberger

Remember what Tesla said:

Experience is made before the law is formulated, both are related like cause an effect. Nicholas Tesla

...once the blood leaves the heart, the arteries do something that actually i have been discussing for a while:

Vortical flow structure identification and flow transport in arteries

1. Introduction
Our interest in vortices arises for two reasons. Firstly, at moderate to large Reynolds
numbers (at least 100) which characterise flow in larger arteries, vortices are quite
persistent. The presence of vortices in a flow may exert a strong influence on its behaviour, although tracking vortices may be difficult as they can evolve rapidly. The effects of vortices or vortical structures are particularly evident when considering both flow stability, and the processes of mixing and transport by the flow. The object of this paper is to examine the dynamics both of vortex motion and of particle transport in arteries, and to relate these to parameters such as geometry and unsteadiness. The Lagrangian particle tracking and the vortex dynamic techniques which are described should help in understanding arterial fluid dynamics and suggest new approaches to modelling.

http://www2.imperial.ac.uk/ssherw/sp...oShFrPe-02.pdf


ps: if you think about it your body generates its own Mstate Water

[MonsieurM]

side note

From the info I have posted so far (and if you do a little research ), you 'll see that there is a trend that appears, and that is for every fractal structure you have seen in nature/universe, the presence of water comes hand in hand


how to make a fractal antenna

http://rexmo.net/pdf/How_to_make_a_f..._DTV_plus_.pdf

plunge it in water, you'll multiply its reception

Scientists believe that the structure of liquid water consists of aggregates of water molecules that form and re-form continually

so this is your adaptive fractal antenna (Liquid Antenna), and the adaptive part comes from the hydrogen bonds

H2O - The Mystery, Art, and Science of Water: Facts

-------

Triple point of water

The single combination of pressure and temperature at which liquid water, solid ice, and water vapour can coexist in a stable equilibrium occurs at exactly 273.16 K (0.01 °C) and a partial vapour pressure of 611.73 pascals (ca. 6.1173 millibars, 0.0060373 atm). At that point, it is possible to change all of the substance to ice, water, or vapor on making arbitrarily small changes in pressure and temperature. Even if the total pressure of a system is well above triple point of water, provided the partial pressure of the water vapour is 611.73 pascals then the system can still be brought to the triple point of water. Strictly speaking, the surfaces separating the different phases should also be perfectly flat, to abnegate the effects of surface tensions.

[MonsieurM]

note


Humans Could Have Geomagnetic Sight

The ability to see Earth’s magnetic field, thought to be restricted to sea turtles and swallows and other long-distance animal navigators, may also reside in human eyes.

Tests of cryptochrome 2, a key protein component of geomagnetic perception, found that its human version restored geomagnetic orientation in cryptochrome-deficient fruit flies.

Flies are a long, long way from people, but that the protein worked at all is impressive. There’s also a whole lot of it in our eyes.

Humans Could Have Geomagnetic Sight | Wired Science | Wired.com

[IndianaBoys]

Dr. Jacques Benveniste - Homeopathy experiment

MonsieurM,,

Thought Jacques Benveniste would be a good addition to your collection.

Dr. Jacques Benveniste digibio part1 of 2
YouTube - ‪Dr. Jacques Benveniste digibio part1 of 2‬‏

Dr. Jacques Benveniste He claims that the "structure" of biochemicals can be impressed on water electrically using white noise and coils, and then the water will display some of the activity of the original biochemical.

Dr. Jacques Benveniste Digibio part2 of 2
YouTube - ‪Dr. Jacques Benveniste Digibio part2 of 2‬‏

Jacques Benveniste Pt 1 (Heretics of Science - 1994) Homeopathy
YouTube - ‪Jacques Benveniste Pt 1 (Heretics of Science - 1994) Homeopathy‬‏

Jacques Benveniste Pt 2 (Heretics of Science - 1994) Homeopathy
YouTube - ‪Jacques Benveniste Pt 2 (Heretics of Science - 1994) Homeopathy‬‏

Jacques BENVENISTE
Homeopathy & Digital Biology
Jacques BENVENISTE -- Homeopathy & Digital Biology

IndianaBoys

[MonsieurM]

MonsieurM,,

Thought Jacques Benveniste would be a good addition to your collection...

IndianaBoys

Thank you IndianaBoys , I would like to point out that this is an open project, so it is not just my collection but our collection , any piece of the puzzle you could add is welcome

[MonsieurM]

MODELING WATER MOVEMENT IN HORIZONTAL COLUMNS USING FRACTAL THEORY(1)

Fractal mathematics has been used to characterize
water and solute transport in porous media (Arya et
al., 1999; Pachepsky et al., 2000) and also to
characterize and simulate porous media properties
(Anderson et al., 2000). From a non-fractal perspective,
the position of any volumetric water content within a
porous media column can be characterized by:
x = λ(θ).tn (1)
where x = Vertical distance within the column [L], λ
= Boltzmann variable [L T-n], t = Elapsed time [T], n
= Time exponent, and θ = Porous media water content
[L3 L-3].
Similarly, the process of one-dimensional
infiltration of water into a uniform soil as a function
of time can be characterized by the Philip (1957)
equation:
I = S.tn (2)
where I = Cumulative one-dimensional infiltration [L],
and S = Sorptivity [L T-n].
In both (Equations 1 and 2) the time exponent (n)
was fixed at 0.5 (Clothier & Scotter, 2002). However
in fractal characterization of water movement
processes in the soil, the time empirical coefficient
was estimated statistically, along with other hydraulic
properties (Guerrini & Swartzendruber, 1994;
Pachepsky & Timlin, 1998).

http://www.scielo.br/pdf/rbcs/v34n4/42.pdf

A Fractal Model of Mountains with Rivers A Fractal Model of Mountains with Rivers | Mendeley

As I said before, water is a fractal adaptive antenna

Francis E. WILKINSON: High-Frequency Transformations

Dancing electrons, whipped to a jitterbug frenzy, are performing miracles of modern alchemy in a backyard laboratory at Glendale CA. Racing back and forth through coils of wire at frequencies up to 100 megahertz, they transform water, natural gas, cottonseed waste, and potato peelings into new and useful substances for industry.

More on this:

Francis E. WILKINSON -- High Frequency Transformations

Felix Ehrenhaft: Magnetic Current --- 9 articles

Can a magnet take water to pieces? No, say physics textbooks. Yes, says Prof. Felix Ehrenhaft, former director of the Physical Institute at the University of Vienna, who now carries on his research in New York. If he should turn out to be right, his findings in the realm of magnetism promise practical applications as far-reaching as the dynamos, motors, transformers, telephones, and radio that have stemmed from Faraday’s research in electricity.

Davey's sonic heater

The design of the Davey's sonic heater is extremely simple. It actually is composed of two major parts only - see Figure K8 (3) from monograph [1/4]. The most important out of these two parts is a resonating hemispherical bowl (1) made of a sound inducing metal plate. The second part is a buffering hemispherical bowl (2) almost identical in shape to the bowl (1). This second bowl has the radius around 4 mm larger than the resonating hemispherical bowl (1). Both bowls are assembled symmetrically one around the other, means the hemispherical bowl (1) is placed inside of the hemispherical bowl (2). Coin is 32 mm wide = 1.25984 inches / Big bowl approximately 1.75 inches wide and .75 inches thick / Small bowl approximately 1 3/8 inches wide. Of course, apart from these two bowls, the heater also includes a long rod, nuts, washers, and electrical wires. These are to hold it together, to supply electricity to both bowls, and to allow the heater to be submerged into water that it heats. But these other parts are marginal additions only. The major parts are the bowls. During experimental production of this heater, the resonating hemispherical bowl (1) usually is made from an old cover for a bicycle bell. The dimensions of this hemispherical bowl are not important. It is only vital that it falls into a sonic resonance at the frequency of 50 Hertz, and that it has the outer surface which is parallel and equidistant from the external buffering hemispherical bowl (2). To each of these two bowls a different wire of the household electricity supply (i.e. 220 V, 50 Hz) is connected. The heater must be submerged in water that it heat. It brings water to the boiling point extremely fast. More details about the design and operation of this sonic heater is provided in subsection K3.3 from volume 10 of monograph [1/4]. After being constructed, the Davey's telekinetic heater must be "tuned" in two different manners. The first tuning depends on providing the hemispherical bowl (1) with such frequency of the own oscillations, that makes this bowl to resonate acoustically when a sound of the frequency 50 Hertz is emitted nearby. The second tuning of the heater depends on appropriate selecting the distance "L" between both bowls (1) and (2). On this distance depends the formation of the standing wave between both bowls. Thus it decides about the energy efficiency of the entire heater. From the information that the inventor repeated to me, I gather that the measurements carried out by New Zealand scientists suggested that this heater may consume even less than the equivalent for around 5% of the energy that it generates in form of heat. This would indicate, that the electrical efficiency of this heater is around 2000%.

the system has become fractal in frequency.

moe-joe-cell





Official Website of The Moe-Joe Cell Spherical 316 Non-Magnetic Stainless Steel Joe Cell



please read

http://www.energeticforum.com/141282-post541.html

http://www.energeticforum.com/135946-post17.html

http://www.energeticforum.com/136257-post20.html

http://www.energeticforum.com/136258-post21.html



you'll find plenty of similarities with previous experiments, i have posted....

[MonsieurM]

read my latest posts on fractal antenna and resonance in my thread: (also applicable to us humans)
starting at post#151

http://www.energeticforum.com/145158-post151.html

In the realm of physics there is a phenomenon known as a 'runaway vibration', and its destructive capabilities is not so much a matter of power or force, but a matter of precision. For this phenomenon to occur you must hit a precise frequency, and remain there for any given length of time (power builds with time at an astounding rate until the vibrating object is destroyed by the force of that power). If you go below that frequency--nothing! If you go above that frequency--nothing, even though you are utilizing more power. If you continue to increase the frequency you may eventually destroy the object, but this is not the same thing as the inherent build up/amplification of power that occurs in a genuine 'runaway' condition. In such a condition it is not unusual for a very small amount of applied power or force to destroy a huge entity! The moment you pass that frequency the destruction stops. If you miss that frequency you miss the phenomena. The basic notion behind all of these matters is that everything in nature has a resonating frequency. Everything composed of matter, or occupying matter is in a constant state of fluctuation, as the realm of quantum physics leaves us to deduce, and if you vibrate any given object at it's resonating frequency, or a harmonic (multiple) of that frequency, it's possible to destroy that object through the kind of power amplification we've been talking about. The vibration being introduced in such a situation is known in physics as the 'forcing frequency'.

Fractals: frequency, the heart, and cancer

YouTube - ‪Fractals: frequency, the heart, and cancer‬‏

remember this formula:

E=M3/4

[MonsieurM]

I would just like to add a post made by

Yes. Particular vibration filtered from entire solar spectrum. I did some experiments with different frequencies of light spectrum and found that they have ability to speed up healing (ectodermal regeneration) as well as penetrating deeper, endodermal layers of skin. This process helps in cases of joint pain, rheumatism and arthritis also, reducing associated pain. We call this a light but really it is a vibration of EM waves. This has been long known and used in treating injuries among Special Forces members and I've seen military reports regarding this matter. Positive effect of certain nm vibrations have been proved and currently used in growing lamps. If we agree that the water is a living form, responding to the magnetic and electric flux (just in case if term Aether sounds too exotic) and we're electrical beings which suppose to live in harmony with nature, than we can understand that water can obtain charge by exposure to certain vibration and sustain this molecular rearrangement. Our body will respond to it accordingly. At least this is the way I understand this process.
Also as Fred posted - fluorescent lights produce so called "dirty electricity". Spectrum of high frequencies which are affecting our neurological system and capable of increasing blood pressure and sugar level - especially important for people with diabetes. This artificial frequency adds nothing good that water and we may benefit from. Rather opposite.

from: http://www.energeticforum.com/person...tml#post137156

+

Water Capacitor Resonance

YouTube - ‪Water Capacitor Resonance‬‏

Capacitor 1000 uF 10 Volts under water

YouTube - ‪Capacitor 1000 uF 10 Volts under water‬‏

Water charging a capacitor

YouTube - ‪Water charging a capacitor‬‏

Wireless Electricity no Battery

YouTube - ‪Wireless Electricity no Battery.wmv‬‏

Wireless Energy

there in Ukraine was researched special forms antennas wich with special generator can transmit and receive without wires energy with loss of less than 1%.

it would be great to have a pick at their antenna, ar at least a translation

YouTube - ‪Wireless Energy‬‏

[MonsieurM]

please read this post before you view the video:

http://www.energeticforum.com/142787-post6.html

This guy used the same concept to transfer energy wirelessly

YouTube - ‪Oil Water and Energy - Energy Transits Water and Oil - Dimensional Imagery‬‏

The 'MT' Unit is a wireless-cordless power supply that can be scaled up or down for use. The 'MT' unit transfers power via magnetic fields to produce electricity in other units.

The Sun transfers power to Planets with Electro-Magnetic Energy causeing Planetary Spin.

Its believed by this Researcher that most Galaxies are Electro-Magnetic, Causeing, mantaining most of any Solar and Plantary Spin of bodys that are in orbits. (Copyright 1980 -2010 Daniel Paris)

http://www.mtunit.com/