Bedini Ferris Wheel Regauging Motor

[Aaron]

Radus Boot & Star Motor Concept

New video that may be helpful

YouTube - Switching Permantent Magnet Field.wmv

@Everyone - Cody,

Cody, just talked to John and you got it right on! That is how it works.

That is the Radus boot and star motor concept.

[Rl2003]

David,

Nice work on the drawing, that must have taken a little time to do.
While your making your corrections, there is one more slight change.
The star motor as you call it has ten coils, five are slightly off from the
other five. If I had to guess I would say about 2.5 degrees, but John
would know more percisely. The magnets stay like they are. At least that
is the way I saw it to be.
Mark P.

Hi all,

I just saw a few stupid mistakes on the drawing sorry I will change them and re-upload .

David Brown (belfast)

[mklimesh]

I got just the wheel 2 or 3 years ago. As I remember it was around $50 with shipping.

Mike Klimesh

Does the shovel work good, just watched the video? We're getting a bit of snow here in Michigan. Did you disassemble your shovel or can you purchase the wheel seperate?

Thanks, Mark

[david.brown]

sorry

Hi all,

I just saw a few stupid mistakes on the drawing sorry I will change them and re-upload .

David Brown (belfast)

Hi All,

This is my first post so please be gentle.

I'm new to forums.

I have been following this post quite a lot hoping to gain a bit of wisdom from everyone and hopefully have a constructive input.

@John Bedini,

I have been studying you technology for a while now and I would just like to say thank you for sharing you knowledge with us.

I have put a very broad brush drawing together, I have still a lot of stuff in my head that I will be putting on to the drawing also the information that you have already posted on the forum I want to put on to the drawing, but I thought I might as well put it out there for discussion, I was hoping that an overview of the entire machine may help the group see something in a different way.

I have a lot to learn and I am very willing to learn, if the drawing is wrong I am more than willing to change it. If it is completely wrong I am more than willing to completely start again.

The drawing is of a 4m tall Bedini Ferris Wheel, I was trying to stay as close to the original size as possible to try and make it accurate.

Hope I can help,

David Brown (Belfast).

[Mark]

33 inch
Wovel :: World's Safest Snow Shovel!

Mike Klimesh

Does the shovel work good, just watched the video? We're getting a bit of snow here in Michigan. Did you disassemble your shovel or can you purchase the wheel seperate?

Here's another option for a 44 inch wood wheel, just need to remove the steel outer tire, or maybe it could be ordered for less with out it.
44 Inch Functional Wood Buggy Carriage Rear Wheel with a Steel Hub and 1 Inch half 1/2 round Steel Tire or Flat Steel Tire

Thanks, Mark

[mklimesh]

33 inch
Wovel :: World's Safest Snow Shovel!

Mike Klimesh

Hey Mike.
What is the diameter of that wheel.

[nvisser]

Got it running with B/C switch and hall.
After years of placing the magnets 'close' on my builds, I got a rotary indexing table so the magnets on the main wheel and the timing wheel on this one are right on.
I need to build a frame for this one to replace the temporary one and get some real bearings.
As adjusted now when I hook up the input battery it kicks backwards to the next magnet then goes the other way and runs.
Its a start (+_+)
Mike Klimesh

Hey Mike.
I like your setup.What is the diameter of that wheel. It made me think that maybe the wheel from a automatic washing machine could work.

[david.brown]

Motor Layout for Discussion.

Hi All,

This is my first post so please be gentle.

I'm new to forums.

I have been following this post quite a lot hoping to gain a bit of wisdom from everyone and hopefully have a constructive input.

@John Bedini,

I have been studying you technology for a while now and I would just like to say thank you for sharing you knowledge with us.

I have put a very broad brush drawing together, I have still a lot of stuff in my head that I will be putting on to the drawing also the information that you have already posted on the forum I want to put on to the drawing, but I thought I might as well put it out there for discussion, I was hoping that an overview of the entire machine may help the group see something in a different way.

I have a lot to learn and I am very willing to learn, if the drawing is wrong I am more than willing to change it. If it is completely wrong I am more than willing to completely start again.

The drawing is of a 4m tall Bedini Ferris Wheel, I was trying to stay as close to the original size as possible to try and make it accurate.

Hope I can help,

David Brown (Belfast).

UPDATE:- 13-01-11.
THE INFORMATION ON THE ATTACHED DRAWING IS COMPLETELY WRONG, AFTER A LITTLE MORE TIME ON THIS FORUM AND FURTHER STUDY I KNOW FOR A FACT THIS DRAWING I ORIGINALLY POSTED IS COMPLETELY WRONG.
I GOT A BIT TO EXCITED AND POSTED IT A BIT TOO EARLY, I SHOULD HAVE WAITED UNTIL I UNDERSTOOD THE MACHINE A BIT BETTER.
EDITED ON THE 13-01-11.

DAVID BROWN (BELFAST)

[John_K]

Why JB says use soft iron

Hi All,

This is why JB says to use soft iron...

Leedskalnin PMH Replication Movie

(Thanks to Guy Bradley on the BM2 list for posting)


John K.

[cody]

New video that may be helpful

YouTube - Switching Permantent Magnet Field.wmv

[John_Bedini]

Bedini GT3

Chuck,
Ok it running, now move the rotor to 1/2 the pole piece and adjust the timing and it will self start. First it will go backwards then it will start.
John B

[chuck H]

Update on 3 pole kit. Now has hall switch. Still need to take readings on everything before next step. Does not self start yet. But I think I know why and will reconfigure it after I take some readings. Then will install cap. Starting to understand johns big wheel a little. Once this is done mabye i will try it on a larger scale... YouTube - bedini 3 pole with hall switch 12 12 2010 3 56 PM

[mklimesh]

It runs

Got it running with B/C switch and hall.
After years of placing the magnets 'close' on my builds, I got a rotary indexing table so the magnets on the main wheel and the timing wheel on this one are right on.
I need to build a frame for this one to replace the temporary one and get some real bearings.
As adjusted now when I hook up the input battery it kicks backwards to the next magnet then goes the other way and runs.
Its a start (+_+)

Mike Klimesh

[woopy]

Hi all

this is the part 3 of my home work on the understanding

i tried about all what i have to disposal on this circuit

I was very surprised ,that the MO (microwave oven ) fan motor coil with about 200 Ohm resistance and on the scope produces really strong kick back spikes,(more than 200 volts) could not light the Led ramp
, as i can easily do with the much lower ohmage PMH coils

OK something to think about

and good luck at all

Laurent
YouTube - pulse motor with pmh armature test 3.wmv

[Matthew Jones]

I am hoping to try this thing either later today or tomorrow, but I had an idea it might be worth testing.
You may wanna see what happens when you close that magnetic loop and make PMH out of the coil. Add the plate across the coil

See if the current draw doesn't go down. You should technically get the same effect out of it, but the magnetic current may hold in the iron. Then all you would need is some real little pulses to change the direction of the existing currents.

I just thought I would put it out, being its an easy test and all.

Matt