My Motors got me to Tap into Radiant Energy

[Ufopolitics]

I already suggested...

@ Machine
I saw your video and attempted to duplicate it . The only way I could get it to do what your system is doing is to lower the voltage going to the pulse drive. I would suspect that you have a dead battery there or are not getting a solid 12 to 18 volts there. Check it out........???????
Dana

Hello Dana,


I already suggested (way back) to Machine...to set a couple of Meters between Positive to Motor and Drains...One Voltage other IN LINE Amp Meter...at least in one Channel/Gate...As I also thought it could be not enough V/A on Coils.
But after watching this last video, and hearing Coils...to me, it is High Frequency feeding those Coils.

At this point, I don't know if your codes include a Fix Frequency already built in...or is it variable through a Pot?...like before at beginning of this Quad Driver Set Up?

I believe I read that you drive your Imperial at 30 Hz...am I right?

Machine is mentioning 150-160?...but am not sure what He is referring to...


Machineeee!!...Where TF are U?!...LOL


Regards


Ufopolitics

[prochiro]

@ Machine
I also looked at your scope view and saw that your two pulses were not the same. Please select a different pin for probably pin 3 as it sometimes does not follow same timer exactly. Change pin number in program also to match your setup.
Dana

[prochiro]

@ Machine
I saw your video and attempted to duplicate it . The only way I could get it to do what your system is doing is to lower the voltage going to the pulse drive. I would suspect that you have a dead battery there or are not getting a solid 12 to 18 volts there. Check it out........???????
Dana

[JohnStone]

....
Of course WE ALL must believe things like this happens...after we all SAW with our own eyes...how the FBI went to a FOREIGN COUNTRY...COWBOYS ....

Yea! The more an entity is organized the more fragile it is and they fear to be threatened. It does not depend if politics or scinece or business or energy supply.
See the story of Babylon: They built the tower as symbol in order to get themselves believe in their power. Why? In their deep conscious they knew they were extremely fragile (it is written there - read it!). In the end they experienced the so called "agency problem". Everybody did what he was supposed to do but the power of their community broke. BTW: The languages arouse long before (see 2 chatpters before). What they lost is being in line with their highly sophisticated and fragile community - the one only line accepted.
That's what we experience in todays powerful states: Babylon Syndrom and fragility and fear. The fear of stumbling giants. No consprancy required.
Please note that we act in this worldwide scenario - making the world less fragile.
And please note: Who were the people inventing technical solutions 150 years before: pastors and uneducated private men in UK. None university mentioned in realation to inventions at that time. Same observation all over the world.
So guys: Be keen and proceed with what you are doing. We are inline with nature's laws. And nature likes ANTI-fragility we are after.
JS

[iankoglin]

John, FYI Monster Driver 5.1 T3001 files has R1 at 470ohms. Any hints where to start to make that change ? Dana what are you using? I should get this right before I get the boards posted to the OSHPark Store. Maybe it works with both values?

Checking to see if they will ship internationally right now... in the state of Washington USA.

@Cornman
Please note this change by John. Check your email.

@Kogs, R1 to 330, not R2

G'day Sampojo
I did send JS a private email when he asked us to as he was really busy
I asked him this question
Q2 The connections to your driver are as I understand are that
K1X06 shows the connections from the Arduino or direct from a PWM osc. output to pin 3 to Opto "A" Pin 2 receives the ground from the PWM generator ground
The other pins are not needed at this moment?
His answer
Yes and no! It depends.
Given you have 5V at your generator or Arduino:
connect
- pin 1 to GND Arduino
- pin2 to output Ardunino
- pin3 to pin 4
- pin5 to pin6
- pin 6 to 5v Arduino
- Please replace R2 1K with 330 Ohm

Twist all leads between driver and Arduino for less crosstalk

I did the wiring Just as he said and my Monster Driver worked OK

Perhaps John you may elaborate on this

Perhaps he was really talking to me regarding my project but my question to him was relating to his Monster driver Ver 5.1
Kindest regards

Kogs just making sure

[Cornboy 555]

Thanks Joe.

John, FYI Monster Driver 5.1 T3001 files has R1 at 470ohms. Any hints where to start to make that change ? Dana what are you using? I should get this right before I get the boards posted to the OSHPark Store. Maybe it works with both values?

Checking to see if they will ship internationally right now... in the state of Washington USA.

@Cornman
Please note this change by John. Check your email.

@Kogs, R1 to 330, not R2

Thanks Soo much, Sampojo, have never populated a professional board before, it will be interesting. have emailed you.

Thanks once again,

Warmest Regards Cornboy.

[Cornboy 555]

Resistors.

Hello Machine, i completely agree, with UFO, from the sound your electronics/ motor coil make, i am pretty sure your gates are ossilating, causing the fets to switch way faster than they should,and causing excess flyback.

It will be interesting when you fit resistors to gates, hopefully that will help.

Regards Cornboy.

[Ufopolitics]

High Frequency Feeding Coils...

Hi everyone

I made a video, it wasn't recorded in the order I made video( it's made of four little vids). It is of the first program Dana wrote, then sub-pulse program at 12v and 3 neons, then 4 neons, then none. Also, I had no gate resistors, so as I add them, I'll make a video so you can see difference. I think/hope we can get this to work.

I'm going to put 20 ohm resistors, to start, on each gate. I have probes on gate 1 and 2.

Testing 2 arduino programs/ and drivers - YouTube

Hey Sampojo, I hate to chime in, since mine isn't working right, but it seems good up to fets. I used the 470 ohm (r1), but no 1k (r2). The opto input does not share ground with r1, as schematic. The opto input, goes to a series 330 ohm, then arduino ground, not connected to driver.

machine

Hey Machine,

Watched Video, and You are right (as Dana) Garry's Codes should work better...less spikes...Dana said was smoother.

I tell You my Opinion, according to the "Noise" of those Coils, My Friend...I did not hear before what your Motor was "doing"...

Motor Coils are being pulsed with "Too High Frequency"...according to the vibration noise they make...Motor will NEVER TURN this way my friend.

Now You mentioned "160-170"...what was that?...Hertz?!...Dana uses 30 Hz my friend...

To me...you should lower Frequency in your Pot (if you have one of course)...or wherever you could do that...lower it


So, the Symptoms I see...are that Coils are being energized with too much High Frequency Pulses...therefore, not "Enough Time" for Magnetic Field Generation from Hot at all...

I could be wrong...

Warm Regards


Ufopolitics

[machinealive]

testing 2 arduino programs and drivers

Hi everyone

I made a video, it wasn't recorded in the order I made video( it's made of four little vids). It is of the first program Dana wrote, then sub-pulse program at 12v and 3 neons, then 4 neons, then none. Also, I had no gate resistors, so as I add them, I'll make a video so you can see difference. I think/hope we can get this to work.

I'm going to put 20 ohm resistors, to start, on each gate. I have probes on gate 1 and 2.

Testing 2 arduino programs/ and drivers - YouTube

Hey Sampojo, I hate to chime in, since mine isn't working right, but it seems good up to fets. I used the 470 ohm (r1), but no 1k (r2). The opto input does not share ground with r1, as schematic. The opto input, goes to a series 330 ohm, then arduino ground, not connected to driver.

machine

[Ufopolitics]

Thanks Hitby13kw

@UFO - Just love what you have up so far . . . . .
when you start to play the video on
the sound is "xed" out and the viewer can't turn it on, all others seem Ok.

hitby13kw

Thanks Hitby13kw, I had this site for a while...just abandoned it...to dedicate to our motors...

Yeah, that video...The FASCIST Country we are living IN...The United States of America...through You Tube and Copyrights BS...Pleasing MAJOR CORPORATIONS... took the AUDACITY...to DELETE MY AUDIO...Believe that?(If You go to You Tube site to watch it there will notice the yellow sign below screen)

Of course WE ALL must believe things like this happens...after we all SAW with our own eyes...how the FBI went to a FOREIGN COUNTRY...COWBOYS STYLE...and took ALL MEGA-UPLOADS Members/Properties...Under Arrest/Seizing...like if they were Terrorists and USA THE INTERNATIONAL POLICE...and brought them to THEIR STILL KINGDOM AND MAIN RULER...The UK...

All to "DEFEND" The MEGA CORPORATIONS OF LOUSY FILMMAKERS OF BS HOLLYWOOD...

So, what could we expect then, about a "Private" Video...made at Home...Not even "Google Ad-sense" Nickel and Dimes BS on it...?

No matter what, I did it WITHOUT You Tube...enjoy the AUDIO NOW...I Upload Video on MY SERVER...Our own players...let's see what they do then...I DO NOT GIVE A DARN SH*T

http://ufopolitics.com/mankind-biggest-deception

It is VERY Clear and stated at the end of video...I am UNDER the Provisions of "Fair Use" (Non Profit Broadcasting) Copyrights Laws...but they do not give a darn...


Regards



Ufopolitics

[sampojo]

R1 Value, Cornman, Boards are in

And yes R1 shall be about 330 Ohms. Some of you tried (can't remember who) 1K and the opto did not work. Sorry - my miscalculation

R2 is there for your convenience in order to use it either as pullup resistor or as series resistor - depending on the type of frequency source you have. You need to calculate the value for your setup.
At Arduino it needs to be a series resistor.

John, FYI Monster Driver 5.1 T3001 files has R1 at 470ohms. Any hints where to start to make that change ? Dana what are you using? I should get this right before I get the boards posted to the OSHPark Store. Maybe it works with both values?

Checking to see if they will ship internationally right now... in the state of Washington USA.

@Cornman
Please note this change by John. Check your email.

@Kogs, R1 to 330, not R2

[Midaztouch]

@Dana, cased JS Monster needed

Hi Dana,

You have been and are a blessing to have around.

The Fire Blade AMEV1(Radiance) is almost under way. I have to present a flawless bike to the track officials before they even think about letting an EV join. The motorcycle shop owner is an old school famous engineer and racer. He likes EV bikes. Japan is small, he knows everyone. This is our best shot to get in sooner, than a lot later.

I met some EE's. I like one, his prices are reasonable, he is well known and he likes what we are doing. He will do the wiring and electrical repairs when needed. He said he can make the JS boards but sometimes, we get lost in translation. My Japanese is not very good and I don't want/need any confusion with the JS Monster.

The motor is all me. I'm using 18awg and ???awg for winding. I should have two rotors in my box. One for endurance and other for short track. I'm still waiting for my oscilloscope on back order.

Dana, I need a special order...water resistant, hopefully compact, cased JS Monster. Food for thought, we will be running the Imperial at 72volts plus. I need the JS Monster working 100% and ready for action. I need it built right the first time. This is the start of our racing team.

Keep it Clean and Green
Richie

[Hitby13kw]

Hello to All,

I am still working on the site...

UFOPOLITICS

Let me know if it works ok.

Regards

Ufopolitics

@UFO - Just love what you have up so far . . . . .
when you start to play the video on
the sound is "xed" out and the viewer can't turn it on, all others seem Ok.

hitby13kw

[prochiro]

@Midaztouch
I respect what you have posted and have found that any prefabbed board will have the same problem. The reason I say this is that you can not get the protection we desire thru just thin copper leads as they are covered with protected coating. Etching a board is so easy and takes thirty minutes and can be piled high with solder. It also is the cheapest board you can get. Give it a try and see. All my boards are now etched.
Dana

[prochiro]

Hi JohnS
I use three separate power sources. 12 to 60V for Imperial, 18V for pulse driver, these share common negative. The third source is ether computer or 5V plugin transformer. No common ground there.
Dana