Bi-toroid Transformer of Thane C. Heins

[mr.clean]

Here is my advice : you can test this setup with Figuera generator model if you can make two AC signals of some power with exactly 90 degrees shift in phase as described in thread related to this wonderful recovered invention. It is the same kind of devices as Thane one except output power is taken from the center coil. I expect much better results.!

Wow, sounds interesting, let us know

[boguslaw]

Here is my advice : you can test this setup with Figuera generator model if you can make two AC signals of some power with exactly 90 degrees shift in phase as described in thread related to this wonderful recovered invention. It is the same kind of devices as Thane one except output power is taken from the center coil. I expect much better results.!

[mr.clean]

Awesome videos, mr.clean



I'm wondering what would happen if you connected the secondary outputs to bridge rectifiers in series, and stored the charge in a capacitor and then pulsed the output of the capacitor to ?

thanks buddy, was easy aside from the ferrite etching with dremel and snapping apart the toroids.

and just last nite actually ive tried taking power from both secondaries simultaneously and got just what Mr.Ohm says

BUT... one secondary on fixed dummy load and the other secondary for output was a definite increase

im still in early testing, but my only concern was whether the output secondary was brighter or dimmer, and it was brighter. In alignment with Mr Heins's claim

[Berg]

BiTT by Berg

Awesome videos, mr.clean



I'm wondering what would happen if you connected the secondary outputs to bridge rectifiers in series, and stored the charge in a capacitor and then pulsed the output of the capacitor to ?

[mr.clean]

my replication

hi all, anyone still working on this?
here is what ive come up with.... my holy crap meter went off...

part 1 output on and off dummy secondary load...
39A Don Smith Device Project: Incorporating Heins Bi-Toroid Technology - YouTube

part 2 input and output readings with improved connections
39B Don Smith Device Project: Incorporating Heins Bi-Toroid Technology part 2 - YouTube

btw the ramp up wave form was an added pleasantry only found at 1.22khz

cores made from ferrite toroids scored and snapped in half to facilitate winding the coils fast.
total turns not counted, added and removed turns according to inductance
1.022mH on primary 20 gauge magnet wire, and 6.3mH on each secondary 26 gauge magnet wire

[vidbid]

VRAM V2 (Vidbid Rotary Attraction Motor - Version 2)

Here's a design that I am working on.



It produces mechanical energy, a low voltage output and a high voltage output.

Regards,

Vidbid

[trivolty]

Thank you. Now to get my hands on some ferrite rods and some thick plastic boards to start working. I will post results when it's done.

[vidbid]

Compression Frame

Hello,

I'd like to replicate this design as it seems simple and replicable with cheap equipment.

I have bought those toroids from Lithuanian guy recently. The design intended was the joule thief. However, I did quite a work with joule thief and didn't find any OU within the design (except it really drew every last bit of energy from 1.5V cells). That design is only voltage/current transponder capable of "tuning" to the load. So if a LED is attached - it "sets" the voltage for the LED and it works, but for the price of accordingly larger current drawn from the batt.

But, concerning the BiTT:

I'd like to ask what to use to stick the cores together (the "crowfoot in the cage" design) - would conductive glue be enough? I don't think holes/steel screws will work. Thank you.

For myself, I wouldn't bother with glue or drilling holes through Ferrite. I would build a compression frame to hold the BiTT together. This how I would put it all together.



Regards,

Vidbid

[gene gene]

In the design by vidbid 2/28/12, if the distance between the secondaries was 10 times less than their distance to the primary, would this not give you the desired 10 to 1 ratio? Flux path.
Gene

[trivolty]

3D BiTT using toroids and rods

Hello,

I'd like to replicate this design as it seems simple and replicable with cheap equipment.

I have bought those toroids from Lithuanian guy recently. The design intended was the joule thief. However, I did quite a work with joule thief and didn't find any OU within the design (except it really drew every last bit of energy from 1.5V cells). That design is only voltage/current transponder capable of "tuning" to the load. So if a LED is attached - it "sets" the voltage for the LED and it works, but for the price of accordingly larger current drawn from the batt.

But, concerning the BiTT:

I'd like to ask what to use to stick the cores together (the "crowfoot in the cage" design) - would conductive glue be enough? I don't think holes/steel screws will work. Thank you.

[arigatou]

No one thinks that the magnetite core and lord C. Hynes Perpetia, generator? In place of steel? By others to copy the work of the project?

[Allen Burgess]

New Bi-Toroid idea.

This attachment was difficult to copy, but it has the essential idea intact. "FreqShift" from the OverUnity Site Bi-Toroid thread has a 3 phase AC line Reactor, coupled with two horseshoe magnets on top and bottem. Pretty cool innovation, may even work!

These ought to be miniaturized and built into stuff!



[ Composed in Blender ]

[vidbid]

New BiTT Design by Vidbid



Here's a new design that I've come up with. This design uses 2 ferrite rings and 3 ferrite rods.

Yep.




Russian M15BA-300-1k Ferrite Ring 100x50x9 mm ,Lot of 6 | eBay



I suppose if you couldn't find a ferrite rod thick or long enough, you could construct magnetite rods.

Reference: Dr. Peter Lindemann Speaks on Magnetite Core Material - YouTube
Reference: Magnetite Cores - YouTube
Reference: Magnitite Cores 2 - YouTube


Enjoy!

Regards,

Vidbid