Bi-toroid Transformer of Thane C. Heins

[Ein~+ein]

Why not contact Thane Heins and tell him you're an EE prof from some revered tech u hoping to replicate BiTT.
LinkedIN Profile Page
LinkedIN Group (Regenerative Acceleration)
SlideShare (79 Documents)

One would think the more BiTT replications, the more credibilty he'd enjoy. After all, his main focus has been on regenerative acceleration. If he were deliberately withholding secrets, why post 'How to's... or is it just a tease to lure unwary, techno-naive investors?

[Web000x]

Hello,
I made & tested the BiTT represented on the photo. The big toroid has 6000 permeability, the little ones 1000. The tested frequencies are 1...20kHz, the loads were symmetric & non-symmetric ones, the primary was in resonance mode & ordinary mode. All the modes did not give any overunity, though there was an extremely high COP when the loads were asymmetrical ones... Where is a mistake? Who knows?

In DLE-TEST05 : Confirmation of the Thane C. Heins' Effect with the BiTT v1.5, Naudin states that the overunity effect seems to be related to a high time constant (L/R) of the primary winding. Your primary seems to have a relatively small L/R and could probably use a lot more turns. Inductance, L, goes up exponentially with each turn whereas the resistance, R, increases linearly. Just keep wrapping more turns onto that primary and see what happens. I'm interested to know as I've tested the Bitoroid configuration before and didn't get the results similar to Thane's. Everything seemed conventional, albeit I was using a non-ideal core for a transformer effect.

Dave

[qvision]

If noone here can help, all i can suggest is searching youtube and finding other replicators and send them a youtube message to start a discussion.


All the best,

[Alexg800]

Alex, the liks are in posts in this thread since you started posting so you only have to scan back a couple of pages to find them.

I have not built a BITT so i have no direct knowledge.

Did you look at Dave's post above yours ?


All the best,

DC.

Yes, I have seen this site. It's very clear from the explanation...
I tried to replicate it as I could...

[qvision]

I have not built a BITT so i have no direct knowledge.

Did you look at Dave's post above yours ?


All the best,

DC.

[Alexg800]

Alex, the liks are in posts in this thread since you started posting so you only have to scan back a couple of pages to find them.

Hello,
I made & tested the BiTT represented on the photo. The big toroid has 6000 permeability, the little ones 1000. The tested frequencies are 1...20kHz, the loads were symmetric & non-symmetric ones, the primary was in resonance mode & ordinary mode. All the modes did not give any overunity, though there was an extremely high COP when the loads were asymmetrical ones... Where is a mistake? Who knows?

[Dave45]

How to Make a Bi-Toroid Transformer and Exceed 100 Percent Efficien...
How to make a Bi Toroid transformer and exceed 100% efficiency

[qvision]

Alex, the liks are in posts in this thread since you started posting so you only have to scan back a couple of pages to find them.

[Alexg800]

Hello,
Please, advice what links you mean. Give me the references, pls

[qvision]

Hello Dave,
Meanwhile I tried another BiTT with my Royer generator. This Bitt has 2 ferrite toroidals with permeability 10000 & 2000. The toroidals are overlaped, not connected side by side as in the previous BiTT. I apply the drawing. The result is the same one - there is no OU...
Sadly. Theoretically it must work, do not understand where my mistake is.
Regards,
Alex

Alex, have you checked out the previous links to Heins' new YT channel as well as searching YT for other BITT experimenters ?


All the best,

DC.

[qvision]

Unfortunatley Naudin has a history of making OU statements then retracting them, but in this case i can believe it.

Someone better-versed in electronics than myself said he also made a mistake in the measurement process, i will find the post and copy it here.

All the best,

[Berg]

Confirmation by JNL Labs

DLE-TEST05 : Confirmation of the Thane C. Heins' Effect with the BiTT v1.5

Thanks to Jean-Louis Naudin.

Cheers

PS: Check out Thane's document:

How to Make a Bi-Toroid Transformer and Exceed 100 Percent Efficien...

[qvision]

This is his company's YT channel, some videos about the BITT have been added :

OTTAWA UNIVERSITY BI TOROID TRANSFORMER vs CONVENTIONAL TRANSFORMER June 2009 - YouTube


All the best,

[qvision]

I would say he is simply redirecting CEMF, so the energy gained is slightly less than what is lost to CEMF and the first law of thermo isn't broken.


DC.

[Ein~+ein]

Am I understanding this right? Seems some attribute BiTT energy gain not to rerouted BEMF but to ZPE. Keep in mind Heins' measurements were in millivolts. To date, has anyone achieved anything more?

Here's what Patrick Kelly, author of Practical Guide to FE Devices told me:

As to where the power gain comes from in the asymmetrical transformers of Thane Heins and Clemente Figuera, I would have to presume that the energy flow is magnetic amplification with power flowing in from the surrounding environment.

...and back in 2008 someone on Google Groups wrote:

The bi-toroid transformer, as pioneered by Thane C Heins, sets up a magnetic flux vortex that is self-sustaining in much the same way that an atom is self-sustaining. The energy source that makes overunity possible in this device is zero-point energy (ZPE).

By the way, Heins recently posted the following PDi Multiple Bi-Toroid Transformer (BiTT) Prototype Testing for MAGNA International