Imhotep's Radiant Oscillator Video

[Inquorate]

Hey guy,s check this out

This guy has got the voltage so high and the current so low that he's getting gaseous streams..

Up the frequency until it goes invisible, stick a segmented surface ie a single wind coil in or near the stream, and the voltage should multiply..

High Voltage

Anyone who wants to stick their hand in these streams (bodkins) should feel safe enough putting their family pet (or a goldfish) in the stream first..

Thinking of building a tesla coil and running it from imhotep coil, and spark gap...

Looks fun.

[ren]

I got some from a microwave. If you are going to buy some try to get 20kv plus.

[Inquorate]

Hv diodes

I want to rectify the output from the ignition coil with two hv diodes to pos and neg of cap from pos of secondary coil. OR use pos and neg of coil and four diodes...

Any tips on which diode to buy from here, or any other sources?? Any suggestions welcome..

RMCybernetics - Surplus Science Supplies

Ta

[sucahyo]

Thanks for the welcome .

Thanks for the answer. The safe part is what I really like to know most. I work as network admin in a factory. Many computer power supply just can't withstand the fluke generated by giant motor in on off mode. I figure that HV experiment is small scale of that and may harm other electronic too. Based from the answer it is safe.

I notice that in some video blue relay that anyone use produce loud buzzing. The noise would reduce considerably if we pry open the blue plastic casing and put it inside something smooth, maybe cotton.

I read that CFL act also as negative resistor. In the Imhotep circuit the CFL put in parallel with load, I assume this will increase the current flow to the load, right? If we put more CFL in parallel there will be more current goes to the load?

If we put CFL in series with the load would the voltage in the load increase without reducing current?

[Inquorate]

More time in the new year?

@ren - haven't had time to try out the PWM yet except to hook it up to my meter. My next project is to make a better lab power supply. I still have a computer power supply I think will do the job.. And I have a few batteries that need recharging..and... And... And...

[ren]

Hello,

I am a beginner, I want to know if anyone ever use wall electricity for lighting up the CFL in the same way anyone use 12VDC?

Would applying 220VAC to the circuit will work if we replace the relay with something like Omron MK3P-I (rated 250VAC, 3 sync contact) ?

And would it be safe for other electronic attached to wall electricity?

Its done all the time. HV/HF from a tesla coil designed to run off mains power. Most designs of this measure usually opt for maximum power transfer for maximum arc display. You could use a neon sign transformer to step up voltage into the 1000's of volts, simple spark gap and tesla transformer.

[Bodkins]

sucahyo nice idea but i ccant help you there( i do used a 12 wall suppy).

Aromaz@All
Can you get two tubes/sphere in your origanal setup in the way i posted in the video?, the thing is anypoint you connect to ground the tube can be used,
warren red the first quote on the 2nd page I like his style

[sucahyo]

Hello,

I am a beginner, I want to know if anyone ever use wall electricity for lighting up the CFL in the same way anyone use 12VDC?

Would applying 220VAC to the circuit will work if we replace the relay with something like Omron MK3P-I (rated 250VAC, 3 sync contact) ?

And would it be safe for other electronic attached to wall electricity?

[Bodkins]

Ren@works ok for me too nolight drop.trying to get it to the front end Try negative of cap to ground sometimes it charges fast depending of your setup.
Warren@ just downloadind the book i see the sumary before but not the book cheers Mr
Had a great xmas got a REALLY good voltage/frequencey/temp/duty cycle,basicly everthing meter so im REAL happy.
Hope was good for you

[ren]

I'll try your circuit. Do the transistors go soft? With Aromaz circuit my trannies keep dying.

Ben, I actually have the circuit setup with the PWM (same one I gave you) triggering the transistor. The h11d1 is an opto isolator, which isnt necessary, but you can use one if you like. If you are going to Jaycar for the parts you will have to get the h11d3, which is the same except rated for 50v instead of 300.

I only noticed the self triggering when I hooked in the solenoid off the HV coil and my PWM input wasnt connected. Mind you I can get 4 lights lit to useable brightness on 24v @ 100-150ma with the PWM in use.

I only posted the above circuit because I found it interesting. The self oscillations only start when the second coil is placed in series with the HV output, and the lights are lit off one wire, which terminates at the last globe, i.e it doesnt hook back into the circuit. I never had any problems with Aromaz circuit, except I couldnt get the lights very bright.

Ill come around sometime and show you how to hookup that PWM if you like

[mlurye]

Inquorate. If you want try my approach. Instead of 2222 I'm using 2n3906 and I have wire from base going around the coil. From the bottom to the middle is the best. Power trannies never died on me. I mostly managed to burn 2n3906 with my experiments, I even managed to explode some

[Inquorate]

@ ren

I'll try your circuit. Do the transistors go soft? With Aromaz circuit my trannies keep dying.

[ren]

@All,
Does a touch change what is happening inside the bulb or inside
the circuit to light the bulb or does a touch change what is
happening outside the bulb and outside the circuit to
to light the bulb or is it both?

Can anyone tell me in which direction the energy which lights
the bulbs flows?

I've seen touching on two videos now that causes a light
bulb to turn OFF. (there are probably more, I know of two)
This is a clue. Touching only "generally" causes the bulbs to light
or get brighter.
We have seen wood transmit a touch.
Has anyone been able to shield their touch from brightening a bulb?
A shield might be used as a funnel to focus energy?

Just
Randy

[mrbreau]

Books for Bodkins

@ Bodkins!
Here are a couple of links to something you MIGHT be interested in. I warn you though, it will stretch your belief system!!!!

Link; www.free-energy-info.co.uk/Davson.pdf
This is is the whole book, 350 pages. While I was reading it I thought of you and your experimentings.

Link; Karl Schappeller: Glowing Magnetism Prime Mover
This is a condensed/exerpted version of the other link, sort of an introduction to the ideas.

Hope you enjoyed your holiday.
Warren
..

[Inquorate]

Touch

If a crystal in salt water has the same effect as touch / nearness, and wood amplifies it and increases the effective distance...... And my video where touching wood lit the cfl only happened when the spark gap was jumped by said touch on wood or cfl,

THEN..

'touch' causes an energy gain to the system.

Also, when I connected only one end of a coil to negative line from ignition coil, voltage increased; spark gap doubled in length..

Tesla said hertz neglected the damping effect air played around the circuit, and this is why hertz mistook longitudinal compression waves for 'standard' em waves.

I'd say we're affecting the local aether stress and thus how energy can move thru system (or not)

I'm doing some experiments into dielectrics and Electrets as soon as the materials arrive in post. I hope to find more answers.. :-)