Barbosa and Leal Devices - Info and Replication Details

[mobigozer]

Maybe Stivep1 can help out?

Hey Clarence

It was sure nice talking to you about all of your experiments

the other day. I just popped in to let you know that I have been

in contact with a gentlemen name YURI who has a version of

the CAPTOR of his own. Totalas put out his EMAIL.

YURI is from the Ukraine where recently the Globalist have

stolen the country blind.

YURI said he is working on an English YOUTUBE video and asked

me what I wanted him to address in the video.

I told him that I would like him to go over the function

of the two transformers that operate at low voltages

and high amperage.

Look for a Video from this genius YURI coming soon.

YURI has patents coming.

BroMikey, maybe contact Youtube-user Stivep1/ Wesley can help with the communication to YURI?

H

[tvka]

About you're R1 and R2 (or L1, L2)

In the vid here I started monitoring the amp's going from the ground through the captor to the load. Thus after the supposed magic'.

The amp's build up while input through the inverter stays the same.

Despite the fact the voltage drops to aprox 130 volt through the ground while having 9 rods, where 1 is input other 9 are output.

Meaning that the sin/cos comparasion is off so its little difficult to tell if there is OU or not. Nevertheless if I reduce the return rods, voltage drops more.

Therefore I assume, more like hoping, that more grounding fixes the voltage drop (as clarence mentioned before).

The beeping is due battery is empty had to recharge it.

Please, ask me more and if you think its hoaxed I make more, and better, video's

Here is the link, feel free to comment and be critic.

Pics of layout, also wound a test coil around perm magnets each holding 10KG. But instead if direct working on circuit it kills the main fuse so I had to put an lamp load behind it ?
Ah well need to know as I going to wind a 500M wire coil for uber highpulsed DC sparking voltage

https://www.youtube.com/watch?v=T1KoyXr6O4Y

Hi!

Sorry, I will not accept videos. Protocol, if you can

This story has nothing to do about ground. It's transformer story.

Yuri_L maybe has solved it. Lenz law is not broken- just utilized.

So voltages in ordinary transformer are in-phase, secondary current lags 90deg. By adding fat secondary shorted and some portion of primary counter winded MAY Be in that portion EMF is induced to counteract primary consumption and fully utilize energy stored in transformers core.

Regards

[djarno]

Now you are going to cheat whole Venezuela! Impressed

Even if it's too complex for you... for society.

If (for some mysterious reason) captors secondary loop gets electrons then them has to add current in secondary.
This current inevitably should transform in primary voltage- to increase it.
Yet you have voltage source on primary! Voltage source ideally has infinite small internal resistance, so it will eat this gain.

That's it.

About you're R1 and R2 (or L1, L2)

In the vid here I started monitoring the amp's going from the ground through the captor to the load. Thus after the supposed magic'.

The amp's build up while input through the inverter stays the same.

Despite the fact the voltage drops to aprox 130 volt through the ground while having 9 rods, where 1 is input other 9 are output.

Meaning that the sin/cos comparasion is off so its little difficult to tell if there is OU or not. Nevertheless if I reduce the return rods, voltage drops more.

Therefore I assume, more like hoping, that more grounding fixes the voltage drop (as clarence mentioned before).

The beeping is due battery is empty had to recharge it.

Please, ask me more and if you think its hoaxed I make more, and better, video's

Here is the link, feel free to comment and be critic.

Pics of layout, also wound a test coil around perm magnets each holding 10KG. But instead if direct working on circuit it kills the main fuse so I had to put an lamp load behind it ?
Ah well need to know as I going to wind a 500M wire coil for uber highpulsed DC sparking voltage

https://www.youtube.com/watch?v=T1KoyXr6O4Y

[djarno]

Now you are going to cheat whole Venezuela! Impressed

Even if it's too complex for you... for society.

If (for some mysterious reason) captors secondary loop gets electrons then them has to add current in secondary.
This current inevitably should transform in primary voltage- to increase it.
Yet you have voltage source on primary! Voltage source ideally has infinite small internal resistance, so it will eat this gain.

That's it.

The secondary with captor does amp building.

I replicated what l did before. But voltage ⚡ drops to much
much.


Vid is uploading, the beep is due battery of inverter is empty.
I'll try to bury raw scrap later

[BroMikey]

Now you are going to cheat whole Venezuela! Impressed

Even if it's too complex for you... for society.

If (for some mysterious reason) captors secondary loop gets electrons then them has to add current in secondary.
This current inevitably should transform in primary voltage- to increase it.
Yet you have voltage source on primary! Voltage source ideally has infinite small internal resistance, so it will eat this gain.

That's it.

I am sorry tvka, I wish I could understand.

I don't understand everything you write but

I am glad you are impressed

Keep trying maybe I understand you later.

[BroMikey]

Hello wantomake,

I have made these direct quotes from B&L themselves before , however here they are again. MY PLEASURE!
attachments as shown.

Respects,

Clarence

Hey Clarence

It was sure nice talking to you about all of your experiments

the other day. I just popped in to let you know that I have been

in contact with a gentlemen name YURI who has a version of

the CAPTOR of his own. Totalas put out his EMAIL.

YURI is from the Ukraine where recently the Globalist have

stolen the country blind.

YURI said he is working on an English YOUTUBE video and asked

me what I wanted him to address in the video.

I told him that I would like him to go over the function

of the two transformers that operate at low voltages

and high amperage.

Look for a Video from this genius YURI coming soon.

YURI has patents coming.

[tvka]

No, these systems use inverter frequency 50hz or 60hz to

collect usable energy so we can run a refrigerator. 7.83hz

is no good for motors. The system puts in a 50hz or 60hz

frequency and 120vac in tiny amounts forcing this small

bit of energy into the ground. Then the earth adds more

to the same format. The Captor sets up the voltage and

frequency, but only provides 5 percent of the load.


The earth energy piggy backs more electrons.

Ride that wave gentlemen. It's like surfing, you get the

board pointed in the right direction and let that ocean

wave carry you home.

You need 60 rods.

Now you are going to cheat whole Venezuela! Impressed

Even if it's too complex for you... for society.

If (for some mysterious reason) captors secondary loop gets electrons then them has to add current in secondary.
This current inevitably should transform in primary voltage- to increase it.
Yet you have voltage source on primary! Voltage source ideally has infinite small internal resistance, so it will eat this gain.

That's it.

[BroMikey]

I have been studying the system, I have a question. These systems are using frequency Schumann?

No, these systems use inverter frequency 50hz or 60hz to

collect usable energy so we can run a refrigerator. 7.83hz

is no good for motors. The system puts in a 50hz or 60hz

frequency and 120vac in tiny amounts forcing this small

bit of energy into the ground. Then the earth adds more

to the same format. The Captor sets up the voltage and

frequency, but only provides 5 percent of the load.


The earth energy piggy backs more electrons.

Ride that wave gentlemen. It's like surfing, you get the

board pointed in the right direction and let that ocean

wave carry you home.

You need 60 rods.

[JESUS PIŅA]

Resonancia Schumann

I have been studying the system, I have a question. These systems are using frequency Schumann?

[JESUS PIŅA]

from venezuela

Good morning friend, please, I would like to contact for their advice, we are interested in developing this technology here in Venezuela, but on a larger scale. Would you be willing to help? Could you give us a course on these energies? And as in the process to develop it.

[mobigozer]

Thank you Clarence

Hello wantomake,

I have made these direct quotes from B&L themselves before , however here they are again. MY PLEASURE!
attachments as shown.

Respects,

Clarence

Thank you Clarence for the info, we can work with that.
As always respect to you.
Btw, hows your friend who worked with Fernando and B&L?
Best regards
Hans

[clarence]

Hey Clarence,
Are B & L correct in that drawing? The input and output are connected to the looped series of rods? Your drawing showed the input rods in the center, separate from the output rods. Is not the idea to input energy into the earth with separate rods, then collect return energy from the earth with multiple output rods?
Maybe my eyes are bad.

@Mobigozer,
I have experimented with north-south or east-west placement of rods to get more out of planet earth. I drove an 8 foot 1/2" copper pipe into the ground north. Then 15 to 20 feet west used a landscaping galvanized nail in the ground. Connected meter leads to both rods, moved the west nail a little north or south to find the sweet spot in the geomagnetic flow. Where I live I get .8 volts dc reading between the two if aligned true east-west.
Just I know the earth ground has potential power.

Just knowledge to encourage,
wantomake

Hello wantomake,

I have made these direct quotes from B&L themselves before , however here they are again. MY PLEASURE!
attachments as shown.

Respects,

Clarence

[luc2010]

Hi,

I will try it and see if i can get any extra from the ground rods!

Thanks BroMikey

Best Regards
luc2010

[wantomake]

Input and output

Hello mobigozer,

the direction is irrelevant.
however the connection method is relevant as was indicated by B&L.
attached is a picture of how they proposed to do so and which I did.

respects

Clarence

Hey Clarence,
Are B & L correct in that drawing? The input and output are connected to the looped series of rods? Your drawing showed the input rods in the center, separate from the output rods. Is not the idea to input energy into the earth with separate rods, then collect return energy from the earth with multiple output rods?
Maybe my eyes are bad.

@Mobigozer,
I have experimented with north-south or east-west placement of rods to get more out of planet earth. I drove an 8 foot 1/2" copper pipe into the ground north. Then 15 to 20 feet west used a landscaping galvanized nail in the ground. Connected meter leads to both rods, moved the west nail a little north or south to find the sweet spot in the geomagnetic flow. Where I live I get .8 volts dc reading between the two if aligned true east-west.
Just I know the earth ground has potential power.

Just knowledge to encourage,
wantomake

[clarence]

Hi Clarence,
Respects Sir for your continuous effort to educate people on smart inventions :

Q: on the orientation of the ground rods. Is it relevant if they are placed specificly in a north-south direction, or 90 degrees turned so west-east (east-west if you like that more)? Because of the magnetic field of the earth? Or is that not relevant?

Thank you,
Hans

Hello mobigozer,

the direction is irrelevant.
however the connection method is relevant as was indicated by B&L.
attached is a picture of how they proposed to do so and which I did.

respects

Clarence