Water Sparkplug

[eternalightwithin]

I'm interested

I have a 5HP engine and the water spark plug circuit ready to go.
I've been wasting time trying to find an adequate spark plug.

David

[Aaron]

regular plug?

David,

Have you tried a resistorless plug off the shelf with the ground strap cut
off? At smaller discharge levels, should hold up pretty good. The one I used
in a lawnmower did with a plasma ignition. I was using 47uf cap dumps to
the coil.

[eternalightwithin]

No didn't try to mod my own. I guess I could just cut off the ground strap with my dremel.

But plasma still spherical, no?

[rosco1]

Plasma shapes...

No didn't try to mod my own. I guess I could just cut off the ground strap with my dremel.

But plasma still spherical, no?

Correct, you will only get a "golf ball" shaped plasma by doing it that way.

By simply removing the earth strap, the spark/plasma will then do its work from the side area of the electrode, not the top, so you are rewarded with a radial firing potential, meaning the spark/plasma can now use a far greater electrode area, that being the entire circumference of the electrode(360 degree).

This is beneficial when the ionisation effect is considered, as it gives more free electrode area to work with, resulting in less missfires perhaps.

The real problem with taking this approach is still in the physical limitations of the materials used to construct the common spark plug. These materials are not designed to cope with the plasma energies you will be applying, so you must accept that rapid plug consumption will be a fact of life if you go about it that way.

[rosco1]

Announcement.

Energetic forum,


I've been asked to make a special public announcement here on behalf of my team, regarding the project we've been secretly working on, namely, getting any and all engines to run without the use of a fossil based fuel.

The readers of this thread would already be aware that Tutanka, Moose53, and myself, have been diligently plugging away at resolving this issue, and we would now like to state publicly that we have succeeded.

We would like to say that we have confirmed the processes required to make any engine run on this new fuel(essentially water).

We are currently in the process of putting together a proof of concept disclosure.

Please allow us a few short weeks to get that done, at which time, we will go viral and make a general media announcement.

There is still much to do with regard to addressing a marketing approach, and we will be seeking advices of those people who are experts in those fields when the time comes, but for now, we simply ask that everyone remain patient and allow us to get on with the task at hand, thereby allowing us to get this project to completion in the shortest possible time.

We formally ask that everyone please respect our privacy and refrain from slowing us down by asking questions of us here on the forum. We also ask that people please stop sending us PM messages for now too.

We need to apply all our time and focus on what we're doing, thus for us to take the time to respond to any questions is only slowing us down as well as slowing down the release of this technology.

Thank you for being patient.

[eternalightwithin]

Wouldn't it have been prudent to not ""take a couple of weeks" But instead release instantly all at once? Always keep your enemies off balance, no?

David

Energetic forum,


I've been asked to make a special public announcement here on behalf of my team, regarding the project we've been secretly working on, namely, getting any and all engines to run without the use of a fossil based fuel.

The readers of this thread would already be aware that Tutanka, Moose53, and myself, have been diligently plugging away at resolving this issue, and we would now like to state publicly that we have succeeded.

We would like to say that we have confirmed the processes required to make any engine run on this new fuel(essentially water).

We are currently in the process of putting together a proof of concept disclosure.

Please allow us a few short weeks to get that done, at which time, we will go viral and make a general media announcement.

There is still much to do with regard to addressing a marketing approach, and we will be seeking advices of those people who are experts in those fields when the time comes, but for now, we simply ask that everyone remain patient and allow us to get on with the task at hand, thereby allowing us to get this project to completion in the shortest possible time.

We formally ask that everyone please respect our privacy and refrain from slowing us down by asking questions of us here on the forum. We also ask that people please stop sending us PM messages for now too.

We need to apply all our time and focus on what we're doing, thus for us to take the time to respond to any questions is only slowing us down as well as slowing down the release of this technology.

Thank you for being patient.

[rosco1]

David.

Wouldn't it have been prudent to not ""take a couple of weeks" But instead release instantly all at once? Always keep your enemies off balance, no?

David

David,

We feel we've waited quite long enough.

We've actually been eager to make a statement here for quite some time now, but up until this morning, we did still have a couple of small issues to contend with, and now that they've finally been eliminated, we can safely announce that we've succeeded completely.

How it transpired is thus, I got an SMS text message confirming complete success, and I was then directed to make that fact known here ASAP.

We do appreciate that many people here are watching our project closely, so we would not have taken the step of making any kind of statement unless we were completely satisfied with the results.

Enemies? We don't worry about that sort of thing.

[gotoluc]

Hi Rosco1,

Congratulation to you my friend

I know you have worked it this for a long time and you all deserve a good

Looking forward in the information you will be sharing

for all the great work.



Luc

[rosco1]

Thank you Luc.

Hi Rosco1,

Congratulation to you my friend

I know you have worked it this for a long time and you all deserve a good

Looking forward in the information you will be sharing

for all the great work.



Luc

Many thanks Luc.

Yes, we've all been hard at work on this project for a long time now, as you know.

To be honest, I'm not feeling too great about the reception we're receiving, and right now I'm just about ready to withdraw from making any further comments at all, such is the disappointment I'm feeling.

When people openly discuss ways of stealing our hard worked for project, well that just makes me want to keep it safe by not providing it to anyone of questionable motive.

I'm not sure what to do now.

Kind of feels like I've wasted my time on this...


Best regards to you Luc, and thanks again.

[gotoluc]

Many thanks Luc.

Yes, we've all been hard at work on this project for a long time now, as you know.

To be honest, I'm not feeling too great about the reception we're receiving, and right now I'm just about ready to withdraw from making any further comments at all, such is the disappointment I'm feeling.

When people openly discuss ways of stealing our hard worked for project, well that just makes me want to keep it safe by not providing it to anyone of questionable motive.

I'm not sure what to do now.

Kind of feels like I've wasted my time on this...


Best regards to you Luc, and thanks again.

I know the feeling Rosco1,

I encourage you to do your best to not focus on this feeling. If you follow it, in the end you may not find satisfaction.

When we unconditionally give then we open ourselves to receiving. We are instruments in the Creation process. If we hold back! nothing changes and nothing gained. However we should not give with an expectation of a gain either! as this will reap a different result.

Sorry for the philosophical speech ... I truly wish you all success

Sharing is the true path to freedom

Maybe we should start a new topic and ask Aaron to lock this one for archive! ...I think that would help get the ball rolling again .... what do you think?

Luc

[rosco1]

Not my thread.

I know the feeling Robin,

I encourage you to do your best to not focus on this feeling. If you follow it, in the end you may not find internal peace and happiness.

When we unconditionally give then we open ourselves to receiving. We are instruments in the Creation process. If we hold back! nothing changes and nothing gained. However we should not give with an expectation of a gain either! as this will reap a different result.

Sorry for the philosophical speech ... I truly wish you success

Sharing is the true path to freedom

Maybe we should start a new topic and lock this topic for archive! ...I think that would help get the ball rolling again .... what do you think?

Luc

Luc, my name is Ross, not Robin.

I joined this site a long time ago, while researching FireStorm, and while it was useful when that concept was viewed as a possible solution, we did deviate quite a way off that course in order to solve the ignition and ignitor requirements for the atomic hydrogen environment.

It's been quite frustrating not being able to make public any close details of our project, but sadly that's just the way it had to be. I'm sure that any reasonable person reading through the negativity which has been openly displayed here by the fringe elements, can probably well imagine the dismay I'm feeling.

I've decided to cease posting updates here now. If the other team members choose to post details, then that's entirely up to them. I'm done with it.

Perhaps the most disturbing aspect for me, is that the fringe element seems to think we've used information gained by being members of this site for our own benefit, which is simply not true. I'd like for someone to show me where we've done this.

Our project is quite different from that of anyone else here, so how can we now be accused of poaching free info? I just don't understand how this accusation can be levelled against us.

Everybody wants everything for free it seems, so I will part company with some free advice, just keep working at your own projects, and don't just sit back waiting for some Saint to come along and hand you their very own hard work for free, that will never happen in this lifetime, or the next.

[gmeast]

information

I had thought that people working on this would have been steadily and continuously releasing information, progress, details. But now I'm hearing expressions like "...marketing strategies..." and so on.

You gotta be kidding me!

Very early on when I joined this forum it was made clear that 'things should be openly shared by all and for the benefit of all...', etc... you know, the very reason for these forums in the first place.

[gmeast]

Luc, my name is Ross, not Robin.
we've done this.

Our project is quite different from that of anyone else here, so how can we now be accused of poaching free info? I just don't understand how this accusation can be levelled against us.


........why are taking up bandwidth here then if your project differs. Get your own forum?


Everybody wants everything for free it seems, so I will part company with some free advice, just keep working at your own projects, and don't just sit back waiting for some Saint to come along and hand you their very own hard work for free, that will never happen in this lifetime, or the next.

.......quit blubbering!

[gmeast]

what next?

.....and now we won't hear anything from these characters for years because they will be backing into their shells, making claims that the 'world isn't ready for their innovation', or 'they must proceed with caution because they are in the cross hairs of the oil companies' or "....we're now soliciting the interests of energy investors so we can build our SUPER DEE DUPER kick ass research facility..."

I can't tell you how many times I've seen this. Half of the LENR research going on right now is scam research aimed as snagging money from well-meaning but ignorant investors.

Oh...I just ran a 7HP Briggs engine (with the wasted spark) on water and 15% isopropanol using my Vexus circuit and the Silver Firestorm Robin made me. I had to sleeve and re-tap the cylinder head to receive the plug. - Just a hint: The isopropanol and water were not mixed but instead aspirated via separate carburetors.

Greg

[Jetijs]

Great to hear from you Greg
Those are some impressive results. What capacity did you use for the plasma discharge? Can you make a video about that?
I am going to work on the genset setup using plasma, hho and steam as soon as my shop is ready and all the cleaning and repainting jobs will be over.
Good that you are still experimenting
Thanks,
Jetijs