Water Sparkplug

[Robert E.]

plasma plugs

How about pure silver as the spark plug ground rod material?? I mean many people use silver coated copper rods as spark gaps. That much silver shouldn't cost too much.

Jetijs, I have some bad news to go with the plugs. I ran to Church and back yesterday, 72 miles,(WITH PLASMA), and pulled a plug and had much,(maybe several thousands of an inch), wear on the steel ball. I am looking to build them out of nickel like Robin David does. Maybe I can send you some of them after doing more testing. Sorry for the bad news but I guess we have to learn the hard way. So they will work fine on regular ignition but not on plasma. Also the miles per gallon did not change from plasma plug regular ignition and plasma plug WITH plasma ignition!!!!!! Bob

[Aaron]

15 pics added

15 pics added - How to Make Plasma Plugs

Please download
http://www.esmhome.org/library/rober...lasmaplugs.pdf

[moose 53]

Hi Luc, To the best of my understanding the outer electrodes of the old plugs I used are a high nickel alloy, no iron involved .

[gotoluc]

Aaron, The material for the ball is Nickel 61 ERNi-1 Tig Rod which I think is just nickel , and the outside electrodes are salvaged from old plugs

Hi Robin,

I was under the impression that the cage was also going to be made of Nickle.

So it's just the ball... I see

Do you think we could use the Nickel welding rods as cage material or are they too thick or thin?

Thanks for sharing and for all your support work to help this topic.

Luc

[ashtweth]

Hi Guys! sorry just in back again from converting the the Farm then did another hydroxy install day after that..Sorry for being late in Aaron, GREAT PDF Aaron, thanks a lot Bro , very easy to navigate for those that just want to cut to the chase. Will update tonight.

Guys its easy to find stuff on the panacea UNIVERSITY dot org site, the Panacea-bocaf might be a bit harder but has a search there.

[moose 53]

Aaron I used a Lincoln Tig welder .

[Aaron]

thanks - welding info?

Aaron, The material for the ball is Nickel 61 ERNi-1 Tig Rod which I think is just nickel , and the outside electrodes are salvaged from old plugs

Thank you!

I'm not a welder or machinist but my friends are. What kind of welding equipment was used for these mods?

[gmeast]

without

Hi thanks for the video Greg. Do you think that we might be able to
run an engine with a plasma spark with the Krupa type plugs but without
the plasma circuits? Are you going to test this?

Thanks jamie

Hi jamiec,

It was a surprise to see the plug display as it did. Our ultimate goal of complete Water as Fuel may need the extra punch of a plasma circuit. However I feel that there can be many benefits using just these plugs with emulsion fuels and GEET configurations.

In my research I will be testing high, high humidity (steam ingestion) with the fuel-air using these nickel plugs - with and without the VexUs Plasma circuit. I will also try and get a pulse from just water.

Thanks for responding. Peace,

Greg

[jamiec]

Hi thanks for the video Greg. Do you think that we might be able to
run an engine with a plasma spark with the Krupa type plugs but without
the plasma circuits? Are you going to test this?

Thanks jamie

[moose 53]

Thanks Bob.

Has anyone done a single half loop on the plugs instead of 2 half loops?

Also, what is the nickel materials for the plugs? Is it just pure nickel? Is that for the both the sphere and loops or only sphere or only loops?

Aaron, The material for the ball is Nickel 61 ERNi-1 Tig Rod which I think is just nickel , and the outside electrodes are salvaged from old plugs

[gmeast]

Krupa's plasma under pressure-inductoin ignition

Hi all,

I uploaded a video showing the Firestorm at no pressure-VexUs on and off and also under pressure-VexUs on and off.

A healthy plasma arc is produced by the plug even without a plasma or CDI driver circuit. It is enhanced somewhat however by the VexUs circuit.

video is at:

YouTube - nickel pressure

Enjoy,

Greg

[Aaron]

updated how to make plasma plug doc

This is updated

Please download
http://www.esmhome.org/library/rober...lasmaplugs.pdf

NOTE: These plugs are patented so everyone knows only Robert Krupa can do anything commercial with them, please respect this and I have no doubt that everyone here does. Anyone can make a personal copy of something in a patent for personal use and that is about it - as far as I know.

[Aaron]

plugs

Thanks Bob.

Has anyone done a single half loop on the plugs instead of 2 half loops?

Also, what is the nickel materials for the plugs? Is it just pure nickel? Is that for the both the sphere and loops or only sphere or only loops?

[Aaron]

Bug Pics

Thanks Greg!

Do you have one folder with all your Bug pics? Do you mind if I put this all in 1 pdf and make it avail for download here?

[Robert E.]

plasma plugs

Can someone post a simple paragraph on the plug material that I can add to the plug replication doc that I posted?

Ash? Did you modify the doc before posting on your website or is it a different one altogether?

I saw a lot of your comments on the materials but is there a consensus as to what is the ultimate material to use?

Aaron, I used steel to make the ball and 1/16 inch tig welding rod to make the cage ground. I have run them 1,000 miles and show no wear with standard ignition. I will have plasma ignition soon and will keep an eye on them. Robin's plugs are more accurate and should work better than mine but right now my plugs are doing very well with 30% better mpg and NO plasma on my 1988 Dodge Raider. Bob