"SALES INFO" Essential HHO "Booster" Components

[Redmeanie]

Jaybone,

I don't know how Red does it, but here's how I wired mine up. (see picture)

The 4DPDT switch doesn't switch anything but the signal line. The ground and power to the board itself are completely different.

Jerry

Thanks Jerry! I was going to post a diagram when I tried, Im full apparently...Im not sure if I clear my images out of my account if they will disappear from the postings. Oh yeah and thats exactly how they go.....

[gashouse24326]

4PDT Switch

Jaybone,

I don't know how Red does it, but here's how I wired mine up. (see picture)

The 4DPDT switch doesn't switch anything but the signal line. The ground and power to the board itself are completely different.

Jerry

[Redmeanie]

Just to be absolutely sure about the IC:
The notch in the 18-pin DIP socket is oriented toward the top of the circuit as shown on the instruction sheet picture?

And the notch on the chip itself lines up with the notch in the socket?

thanks!

Scroll up in this thread and look at Jetijs' post where he put pics (its on the second page). I believe I did also. That is the best way to tell you. The sockets orientation doesn't really matter as long as the IC goes in right.

[jaybone]

one more thing

Just to be absolutely sure about the IC:
The notch in the 18-pin DIP socket is oriented toward the top of the circuit as shown on the instruction sheet picture?

And the notch on the chip itself lines up with the notch in the socket?

thanks!

[Redmeanie]

I am making pretty good progress on the eife build.
Thanks to Redmeanie for the great kit.
I am having trouble getting my head around the 4PDT toggle switch.
could anyone please give me some guidance on connecting the toggle?
which wires go to what posts?
I am using the dual eife, and have already found the signal and ground leads for both sensors.
Thanks!

Ok,
Sit tight I will try and draw up a diagram on the 4PDT switch for you....

[CaptainCrunch]

Hello all I am new...

I know that there is a new forum section, but had some quesitons. I have been following David Lawton, Stan Meyers and Ravis work for some time now. Does this cuircuit replace the OS Sensor for the ability to add the Fuel Cell without the engine running leaner? How do you tell if the engine is runner leaner? I am interested in building a Fuel Cell and putting it in my trunk and running the lines along with the gas fuel lines to the intake manifold. Has anyone attempted running it from the trunk?

I am interested in the kit, but I am trying to make sure I understand where everything falls in line.

I don't want to seperate this thread, so feel free to private message me in not appropriate here.

[jaybone]

toggle question

I am making pretty good progress on the eife build.
Thanks to Redmeanie for the great kit.
I am having trouble getting my head around the 4PDT toggle switch.
could anyone please give me some guidance on connecting the toggle?
which wires go to what posts?
I am using the dual eife, and have already found the signal and ground leads for both sensors.
Thanks!

[Redmeanie]

RedMeanie, Is there a parts list available for the EFIE and PWM? I have three of these to build for all of my rides. I want to get a headstart on ordering the extra electronics for the other boards. I noticed you stated that you use quality electronics. Where should I order from to make sure I get the "Good Stuff"? I have been using All Electronics for years for resisters, diodes and simple relays but I dont know about the quality of the other parts I will need for these units. Also, could I get an ETA for the order? I am planning a trip and want to test this out then. Thanks!

Yes there are parts lists and everything included. If you want quality parts go through Digi-Key. I use all electronics for stuff too, like resistors and the like. Just not for IC's or semi-conductors, since these are static sensitive and All Electronics doesn't seem to do much to protect from that unfortunately.

I also PM'd you on shipping.

Thanks,
Lee

[hioctane]

Parts List

RedMeanie, Is there a parts list available for the EFIE and PWM? I have three of these to build for all of my rides. I want to get a headstart on ordering the extra electronics for the other boards. I noticed you stated that you use quality electronics. Where should I order from to make sure I get the "Good Stuff"? I have been using All Electronics for years for resisters, diodes and simple relays but I dont know about the quality of the other parts I will need for these units. Also, could I get an ETA for the order? I am planning a trip and want to test this out then. Thanks!

[Redmeanie]

RedMeanie. Does the EFIE unit have a toggle on/off swith to bypass or eliminate its voltage input or is the input thresh-hold set so when it is turned all the way down it has no effect on the O2 sensors reading? I have an order in for the EFIE and PWM and can't wait to get this setup on and tested. I have been using O2 spacers and a straight wired Booster. But I only drive 2 miles to work so I have not yet seen any savings. A road trip could tell me though. The pics of all the kits put together look great! I have dusted off my soldering iron and am ready for this! Thanks!

Yes, There is a "By-Pass" switch that takes it right back to stock if you ever need to switch it off.

[hioctane]

Switch for EFIE

RedMeanie. Does the EFIE unit have a toggle on/off swith to bypass or eliminate its voltage input or is the input thresh-hold set so when it is turned all the way down it has no effect on the O2 sensors reading? I have an order in for the EFIE and PWM and can't wait to get this setup on and tested. I have been using O2 spacers and a straight wired Booster. But I only drive 2 miles to work so I have not yet seen any savings. A road trip could tell me though. The pics of all the kits put together look great! I have dusted off my soldering iron and am ready for this! Thanks!

[ATechguy]

Mod Efie for wideband

HI! can you mod the Efie for more offset voltage for wideband 02?? Change 200k variable Pot. to 10k or if that is to low what can the circuit handle ??I need to off set more volt to the ecu . The WB 02 operates on 1 to 5 v. Any help???

[InTheField]

Sssshhhweet!

[gashouse24326]

A look at the project

Ok all. I thought I'd share a few images of my EFIE project, and once again thank Red for this great setup. A little trimming to fit the boards into a Radio Shack project box, and a little soldering and planning and I have this.

[InTheField]

For InTheField, I'm sure that Red can answer the question himself, but just to let you know, I thought the same thing when I received my kit. A closer inspection showed that there were enough legs on the both of the switched to handle both EFIE's. It took a little bit of figuring, but that's how I wired mine up. I think that I recall him mentioning something about wanting separate controls for both EFIE's or a single control for the pair of them. The way that I wired it up seems to work fine.

D'oH! Yeah, you're right... Red asked me about that too... Only needed one set of controls for the dual setup. Lack of sleep... that's my excuse! Off to the second job!

Again, Nice Kit!