"SALES INFO" Essential HHO "Booster" Components

[Redmeanie]

EFIE Tuning....

Everyone that is building the EFIE that I sent the "Mixture Control" Document to use this one instead until Tux and I can rewrite it. I already know how to calibrate it, so I had Mira try, and well lets just say the instructions I sent (I didn't write those ) were less than user friendly.
So I have a copy of Patrick Kelly's rewrite, these are allot clearer, and based on the design that the Controller I offer was based on. So just disregard the schematic because it's different, but DO EVERYTHING ELSE the same!

[ashtweth]

great work man, i am almost finished the complete design hydroxy write up for the uni site, its just being proof read and edited now, plus re drawn in some places, will send it off to you guys to test drive when done.

[TuxAir]

Thanks a bunch RedMeanie.

To everyone else. Once I receive the kits from RedMeanie, I will start off by making a step by step (pictures too) of each component as it gets built. This way we will all learn together as this thing evolves. The installation and adjustment write-ups will be a bit broader in perspective as each vehicle is different, but the concept and basic hookups should be the same. Any contributions to these write (including information borrowed from other peoples write-ups) will be properly credited.

Since Redmeanie put these kits together so well and with great documentation, I ended up going with a companion manual idea for the PWM & Fuel Mixture Controllers to keep redundancy down The first draft is complete and sent off to Redmeanie for review/additions/corrections etc.

[wpage]

Kit not working for me...

I wish I had ordered the kit with the pre drilled board. I fat fingered this thing. Red I need to order a pre drilled board for this EFIE.

Dont want to install this and fry my ECN or Sensor!

Red

Let me know the price for a subsequent order for one. (Saw it as a $2.00 option in the kit with initial offer) Not sure about shipping and handling.

Thanks

[ashtweth]

Australia has the First Redmeanie EFIE's
Arrived today, i have to say Lee what a package, very professional, great info in there and manuals didn't expect to get such a awesome package man

[Jetijs]

LOL
We on the other hand are supposed to think that all Estonians are a bit slow in the head, but I am sure that neither of us mean that seriously. After all, we all are brothers with very similar and hard history

[wpage]

Jet

Today I soldered together my EFIE:


Many thanks to you, Red!

Jet,
Nice looking job. Can we get a reverse view and any solder tips for trimming excess wire.

PS My friend from Estonia, Uno says all Latvians are poor fishermen. Is that true?
W

[Jetijs]

Today I soldered together my EFIE:


Many thanks to you, Red!

[wpage]

Rotary switch & enclosure questions

Red,

Got the EFFIE package very nice!

Thinking about how to best run my controls back to the cabin...
-Thinking of using a 26ga cat 5 type com wire 4 pair to wire out my board. What do you think of
a. orange pair bypass switch
b. other 3 pair for 6 position switch for rotary selector contols
from that is there any sequence recomended for contacts? Blue, Green, Brown pairs.

-Mounting board in enclosure in engine compartment. Any environmentals to suggest?
Should the little light be in the cabin for visuals. If so I guess the whole thing should be in the cabin of my rig.

Thanks

W

[cyberphreax]

Sure just email me, [email protected]. I will send you what I have. Also is that Fuel Mixture Board one from the net, with a PCB layout included?
If so when you email me send that along and I can add that to the kits.

I sent you an Email Friday. I just wanted to make sure it didn't get caught in any spam filters. I'm re-designing the 20 led AFR. I'll send you the files after I've built and tested it.

[Redmeanie]

I really didn't need to know anything in particular about them. Like you said, it's easy enough to look into and see most of what's going on, and anything I can't see I can use a multimeter to figure out. I just kind of like data sheets and was wondering if there was one for this switch that gave general information, like current ratings and dimensions and such in case I ever need to replace this one or want to build another unit. Well, that and I'm going to have to figure out how to connect the switch to both efie's. I always prefer to have as much knowledge about anything as I can.

Yeah, I did get the parts sheets and they were very helpful. In fact, the only thing you've done wrong as far as I can see is to make it so that if I screw things up, I have to live with the knowledge that I'm not as skilled as an 8 year old girl.

Keep up the good work.

Sure Thing! I will try and get one for you, at least a part # from them next time I go up there.

Also I have spec sheets on the main components if anyone needs them.

I really think she is a natural! All I made her do was practice on 2 boards until she could put down one little pad droplet. Then I put in 1 part at a time for her and she soldered them in one at a time!

[gashouse24326]

What did you need to know on the switches? I source those locally, and I don't think I have ever seen a spec sheet for a rotary before. I can look into it. But if you have a question on them I can probably answer it.

As far as wiring goes, I use 16G for power, 22G for Signal, and 14G or 12G off of the Mosfets depending on the set-up.

You did get the Part ID sheets and Diagrams Right? I know how it is with the small parts, I have a hard time with them also, thats why I use those little tricks like that!

I really didn't need to know anything in particular about them. Like you said, it's easy enough to look into and see most of what's going on, and anything I can't see I can use a multimeter to figure out. I just kind of like data sheets and was wondering if there was one for this switch that gave general information, like current ratings and dimensions and such in case I ever need to replace this one or want to build another unit. Well, that and I'm going to have to figure out how to connect the switch to both efie's. I always prefer to have as much knowledge about anything as I can.

Yeah, I did get the parts sheets and they were very helpful. In fact, the only thing you've done wrong as far as I can see is to make it so that if I screw things up, I have to live with the knowledge that I'm not as skilled as an 8 year old girl.

Keep up the good work.

[Aaron]

School Girl EFIE

First the School Girl Motor, now the School Girl EFIE...I love it!

[Redmeanie]

That does look pretty good Red. You must be very proud. I come back for help again. Any chance of getting a part number for the rotary switch? I'm trying to look up accessories(and possibly a data sheet)for it and I"m having trouble locating anything like it in the DigiKey catalog.

What size wire do you recommend for the power lines and for the wires going to the switches?

As an aside, I don't think that I've seen it mentioned online and if it came with the nifty pages that you sent with each of the boards, then I missed it there, but thanks for leaving the tape on the ends of the zener diodes. My eyesight isn't the greatest in the world, and that was definitely a nice touch.

Thanks a bunch.

(I really need to get a sig)

What did you need to know on the switches? I source those locally, and I don't think I have ever seen a spec sheet for a rotary before. I can look into it. But if you have a question on them I can probably answer it.

As far as wiring goes, I use 16G for power, 22G for Signal, and 14G or 12G off of the Mosfets depending on the set-up.

You did get the Part ID sheets and Diagrams Right? I know how it is with the small parts, I have a hard time with them also, thats why I use those little tricks like that!

[gashouse24326]

That does look pretty good Red. You must be very proud. I come back for help again. Any chance of getting a part number for the rotary switch? I'm trying to look up accessories(and possibly a data sheet)for it and I"m having trouble locating anything like it in the DigiKey catalog.

What size wire do you recommend for the power lines and for the wires going to the switches?

As an aside, I don't think that I've seen it mentioned online and if it came with the nifty pages that you sent with each of the boards, then I missed it there, but thanks for leaving the tape on the ends of the zener diodes. My eyesight isn't the greatest in the world, and that was definitely a nice touch.

Thanks a bunch.

(I really need to get a sig)