Bedini Ferris Wheel Regauging Motor

[ren]

synchro

Ren can direct the questions to me and not other people on other groups as they do not know how to answer correctly.

Current is not the important thing in these machines as it was meaningless at that size. The re-gauging Motor was running on two pulses at less then 350 Ma at 42 foot pound of torque at 6 to 7 RPM's. At every dot located on the motor/generator it was switched on ( in the pictures) The machine was less then 1.2 amps total for 36 volts in run mode.

Hope this answers Ren's questions. I brought everybody up to the machine so they could look at the meters for themselves. The volt meter was a hot wire meter very true in it's reading input battery dead 36.1 but showing charge 37.3, volts output battery reading 45.2 volts meter pegged to one side.current at 3.1 amps. So you can figure from here. This is all caught on film as Tony was filming the meters and the voltages and people going right past the meters without looking. and also Bit's had one running all day driving a load.


I think the problem is that no one believes what Tom Bearden and I have been screaming about for years. Start reading all you can because you must change your thinking for this one. And no one measured the coils because I told them what it was, as I said during my talk, I tell the truth because your not going to believe me. it's up to you to do the experiments, I have already done mine and have shown the machine. I tied this all into ED's work because this energy is all the same thing whether you use rocks or wood. it's all magnetic energy every bit of it.
John

Thanks John,

Your first post in response to me (as well as the one above) has been very helpful . I know you've taught us that its not about current but your details above do give me an idea of how hard its pushing and does help.

In regards to the axial arrangement, can I assume that all magnets are all north? And its a little hard to tell from the photos, but there was some references before to the coils being staggered, so that they are not all aligned to a magnetic pole at once. Somewhat like Bill Muellers device perhaps. Looking again at one of the photos if they are a staggered alignment it doesnt look like its by much. The reason I ask is because you have mentioned that the coils fire 5 times per revolution and that they are all in series. I was wondering if they were designed for repulsion only.

I am particularly interested in the axial side of it for the moment. I have some questions regarding the unusual magnet arrangements, but Id like to frame the questions better in my mind before I ask. I assume its the same circuit 1/2 Bedini/Cole for the axial generator as well? Does it source its power for the 5 pulses per revolution directly from the source battery? Ive been playing around with a 2 phase SG with which the inductive discharges are collected in a capacitor and the second phase of the SG is run from this capacitor, I wondered if perhaps the axial arrangement may be run off the bridge/cap off the radials recovered energy?

Finally, a small question regarding your choice of timing magnets. Your first window motors used a rectangular magnet, I notice recently that you are using discs. How do these work in comparison to the latter, do they allow for more precise timing of the halls or are they simply what you had on hand and work as well as the square/rectangulars.

Thankyou for taking the time to respond to this thread.

Regards

Shanan Reynaud (Ren for short )

[John_Bedini]

big Bedini Motor

synchro

I can not answer that question here as this is completely off subject here.

Ren can direct the questions to me and not other people on other groups as they do not know how to answer correctly.

Current is not the important thing in these machines as it was meaningless at that size. The re-gauging Motor was running on two pulses at less then 350 Ma at 42 foot pound of torque at 6 to 7 RPM's. At every dot located on the motor/generator it was switched on ( in the pictures) The machine was less then 1.2 amps total for 36 volts in run mode.

Hope this answers Ren's questions. I brought everybody up to the machine so they could look at the meters for themselves. The volt meter was a hot wire meter very true in it's reading input battery dead 36.1 but showing charge 37.3, volts output battery reading 45.2 volts meter pegged to one side.current at 3.1 amps. So you can figure from here. This is all caught on film as Tony was filming the meters and the voltages and people going right past the meters without looking. and also Bit's had one running all day driving a load.


I think the problem is that no one believes what Tom Bearden and I have been screaming about for years. Start reading all you can because you must change your thinking for this one. And no one measured the coils because I told them what it was, as I said during my talk, I tell the truth because your not going to believe me. it's up to you to do the experiments, I have already done mine and have shown the machine. I tied this all into ED's work because this energy is all the same thing whether you use rocks or wood. it's all magnetic energy every bit of it.
John

@John Bedini

How does the big 200 pound 4000 turn Quadfilar use impedance to amplify magnet strength?

How can I apply your approach to improve my 4 wire Spiral Knot Torus?

[Bill H]

Bedini/cole switched SSG

I am pumped to try some new circuits. I am going to start by converting my 8 circuit single coil ssg into a hall trigger bedini/cole switched machine and then scale up from there, one step at a time.
John K. I take it you are going to work along a like path, I would love to work along side you, yet thousands of miles apart if you would have me.
Really wished I had been at the convention but there was no way to make it happen, but with the extra time to plan for the next one I would say right now there is very close to a 100% chance I will be there. (don't tell my wife I said that).
Bill H.

[synchro]

Big four wire coil.

@John Bedini

How does the big 200 pound 4000 turn Quadfilar use impedance to amplify magnet strength?

How can I apply your approach to improve my 4 wire Spiral Knot Torus?

[John_Bedini]

Bedini Big Motor

I'm also going to point out that the capacitor is 16000 Uf at 75 volts 95 surge.
John

[John_Bedini]

Big Bedini Motor

Jeremy,
Move the right coil to almost TDC 1/8 past move the center coil to 1/2 past TDC to the right the you will be very close on your drawing. The axial motor is in-between the rotor magnets so it holds it off center for start condition. That is why the motor goes reverse slams agents the magnetic field and then takes off forward.John

[John_Bedini]

Bedini Big Motor

Mark,
The coils are in phase, for a measured inductance of 12.6 ohms. What everybody is forgetting is the rotor is held in magnetic lock condition by the axial motor/generator as I showed this at the conference when starting the re-gauging motor.

Again do not use reed switches on this machine, it uses halls. Peter also pointed this out about the magnetic lock.John

[lanenal]

correct drawing?

Jeremy,
You are correct except your a little off on the outside coils as far as spacing goes.
But with a little adjustment this will work, past TDC 23 DEG. When adding Iron you cause a resistance/delay in the magnetic field. you can cause non liner action in the field emitted. Good drawing.
John B

Hopefully this is the correct drawing according to JB's comments.

See attached.

lanenal

[Mark]

I am trying to get an understanding of how the 3 coils on the bottom are operating, please correct me if I am wrong.

The way I'm seeing this is the center coil is firing a north field and the other 2 coils are firing a south, all magnets have north facing out. The coils are actually firing when the magnet is .5 degrees past TDC of the center coils core. This pushes the magnet away from the center coil while drawing the magnets toward the other 2 coils which are approx. .5 and 1.5 degree before TDC.

Am I totally off track here? But the way I see it, to drive the wheel the magnet would have to be just passing the center coils core while the magnets haven't quite reached the outer coils cores.

Please help me to understand, I might be more lost here than what I thought.

Thanks Mark

[sucahyo]

Sucahyo,
I can only report what I was told, The women in the room felt relief in pain when standing next to the machine. I guess people do not know anything about Scalar Interferometry in magnetic systems. Also I called a woman to the stage to give you a report on what she saw happen, if the energy is good without harm plants go nuts and grow like mad.

If the energy that is emitted from the machine is harmful you end up like Floyd Sweet dead all at once, that is why I stay away from that device Floyd built. I worked with him for 2 years know everything about his device and what could happen if your not careful with negative energy, things just explode for no reason. I had that problem when I was first tuning the machine, so a warning be careful with inter active fields.
And yes I did call everybody up to feel that experience of scalar fields

Thank you very very much . I am very grateful for this confirmation .

I have been using my radiant circuit to help cure insomnia, to promote sleep. It works for my family and confirmed by Godfrey. I do not doubt at all if some lady report relief in pain or if plant grow at wild rate.

I am only at the lowest foot step but I am really happy that what I have been suspecting for months now is not just my illusion. I have believe that you also manipulate scalar, not just electricity or magnetism. I think I understand the point about harmful, some circuit in this forum noticed by some people to produce headache. I hope that after reading your post, people who embrance headache can now realize the danger.

Thank you again .

[John_Bedini]

Big Bedini Machine

John K,
NO more Winter Shows, it freezing ass cold here I think it's going to drop into the single digits this week. That is a good test for batteries outside to see what they do when they have a negative charge. It's like someone just sucked all the heat out of here. I want to see what a much bigger machine does now it's intriguing to me too, but I'm not afraid of it in anyway
John B

[John_Bedini]

Big Bedini Machine

John K,
Yes you are very close, set the machine to kick backwards first the timing will be real close then. We will go drink beer when you come up.
John it's easy to build since you have all the experience of the monopole group, Jeremy is right Free 100% negative switching no loss.
JB

[John_Bedini]

Big Bedini Machine

Sucahyo,
I can only report what I was told, The women in the room felt relief in pain when standing next to the machine. I guess people do not know anything about Scalar Interferometry in magnetic systems. Also I called a woman to the stage to give you a report on what she saw happen, if the energy is good without harm plants go nuts and grow like mad.

If the energy that is emitted from the machine is harmful you end up like Floyd Sweet dead all at once, that is why I stay away from that device Floyd built. I worked with him for 2 years know everything about his device and what could happen if your not careful with negative energy, things just explode for no reason. I had that problem when I was first tuning the machine, so a warning be careful with inter active fields.
And yes I did call everybody up to feel that experience of scalar fields

The machine was set to emit between 6.85Hz to 7.1Hz The rpm of the machine was between 16.5 to 18 RPM's depending on the solar radiation at the time. You could not possibility learn enough about this machine unless you build one that big.

In Jeremy's drawing I will tell you the correction, The center coil is 1/2 the pole piece to the right, the left coil is 1/4 past the pole piece, and the right coil is almost TDC the difference is in the straight on pictures that Tony took at the show. The picture is deceiving because of the magnetic holders. How many were standing around when I slammed the magnetic fields backwards and bounced the 300 lb rotor to a dead stop then full force forward.

Group this is a very tricky machine to build not for the faint hearted, I would estimate the machine at over 3 to 1 The Raytheon boy's said the same thing to me in the hallway.
JB

Thanks for sharing . Do we need to also put some thought to the wiring?

Do this energy is the same energy that some people feel around the big wheel?

"I think he wanted everyone to feel the energy around the machine. It permeated your whole body! My jacket was vibrating!"

[jerdee]

Thank you very much John!


Aaron,

The two inches...looks to be much closer to the correct calculation.

As far as the potential switch from FEG 49. The 32V Zener does it all! Completely free switching here...no 555 at all! This switch is taking advantage of the inverted phase potential. Negative Charging!! Completely out of phase from input circuit. FULL RECOVERY AND COMPLETELY FREE!!

The 1200uf 75V cap is charged to approximately 72v (approximately 5 x constant) and discharged at potential difference of an inverted phase of 36 volts!! Remember it's much easier to fill it half way!! Step Charge!!!

Still learning here, but I getting more an more excited about this completely non-linear arrangement!!! VERY VERY interesting.

Absolutely amazing work John, your best yet!!!

Regards,
Jeremy Burnum

They look closer to maybe 2 inch off from the looks of the pics:

From the center of the coil at the top of the pic to the center of the big
magnet looks about 2 inches or about 2 of those silver neo magnet widths.

Is the potential switch identical to page 49 (FEG book) even with the 555 timer
and opto isolator? Some people were commenting on a zener but I wasn't
by the wheel when that conversation was happening.

[Aaron]

coil placement and potential switch

They look closer to maybe 2 inch off from the looks of the pics:



From the center of the coil at the top of the pic to the center of the big
magnet looks about 2 inches or about 2 of those silver neo magnet widths.

Is the potential switch identical to page 49 (FEG book) even with the 555 timer
and opto isolator? Some people were commenting on a zener but I wasn't
by the wheel when that conversation was happening.