Announcement

Collapse
No announcement yet.

Bi-toroid Transformer of Thane C. Heins

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • x_name41
    replied
    hello to all, i made little experiment with bi toroid transformer, and results confirmed declared characteristics and specifications referred on the patent

    schematic:


    physical realisation:


    and oscilloscope waveforms, red waveform is current and green waveform is voltage

    waveforms in the resonant circuit with load in the secondary coil


    waveforms in the resonant circuit without load in the secondary coil


    waveform in the secondary coil with load


    and waveforms in the resonant circuit with short circuit in the secondary coil


    and results of the measurements in the idle mode = 3.60V./0.53A., with load in the output coil= 3.70V./0.53A., and in the short circuit mode in the secondary coil = 3.09V/0.55A. Solely now my scheme is not a perfect because reactive power in the resonant circuit was minimal (something in the scheme impede the preparation of normal reactive power even at idle), i no hurry, a matter of time just while fix the problem
    because the frequency is of the order of 70-80KHz, soundcard oscilloscope at the smallest possible range, shows the triangular waveforms of current and voltage dephased of the about 90 degrees, at change of the range is observed following picture, sinusoidal waveforms are expanded and narrow the, like mech an accordion, and the waves are again at 90 degrees.

    source: COP 20.00 (2000%) Times, Reactive Power Energy Source Generator,
    Форум странников :: Тема: Би-тороидальный трансформатор Thane C. Heins (2/2)
    Експерименти на x_name41

    Leave a comment:


  • BroMikey
    replied
    OU circuit

    Originally posted by mr.clean View Post
    hi all, been busy but i wanted to try the JLNaudin MEG circuit on the Bitoroid, pretty good, so im gonna do some more experiments soon...

    BiToroid Resonant Driver: MEG Circuit - YouTube
    Hey Clean

    That is OU. I know you didn't want to say it but all of the bi-toroids are known for more out. That is besides the point because you are doing more than toggling circuits.

    You are inspiring 1000's to do some of this testing great works. If I keep watching you I will get my bearings one day and do some of these experiments.

    Mike

    Leave a comment:


  • artoj
    replied
    Missing meter

    Add one more meter, between the wall outlet and the power-supply. Measure before and after the time event.

    Leave a comment:


  • kEhYo77
    replied
    Hi. The best setup to date is here: Measurement of the DC INPUT CURRENT on the BiTT v2.1
    When the load is connected the input current DOES NOT CHANGE!
    You can build this BiTT with 3 "C" ferrite cores.
    Then make LC tank on the primary and drive it at resonance.
    Good luck

    Leave a comment:


  • tturner
    replied
    been awhile

    im a complete newbie but liked bitt bc its simplicity wondering if any new progress has happened in the last month i would like to replicate if it works bc im if anyone could suggest something on the same difficulty level that they know work would be great pm me

    Leave a comment:


  • tturner
    replied
    been awhile

    im a complete newbie but liked bitt bc its simplicity wondering if any new progress has happened in the last month i would like to replicate if it works bc im if anyone could suggest something on the same difficulty level that they know work would be great

    Leave a comment:


  • tturner
    replied
    been awhile

    im a complete newbie but liked bitt bc its simplicity wondering if any new progress has happened in the last month i would like to replicate if it works bc im in a energy crisis

    Leave a comment:


  • mrtarslan
    replied
    Sorry, i dont understand, how can i calculate this bi-toroid transformer for from specific power input to output power? Is there any calcutation for cable thickness and turning and transformer core dimensions?
    Thanks, good days.

    Leave a comment:


  • Berg
    replied
    Bi-toroid Transformer Sayings

    Originally posted by mr.clean View Post
    i find that a single positive square pulse can only go so far before the core is saturated, the Mazzilli push-pull circuit worked well, but in tuning a pos and neg pulse h bridge worked best.

    one thing is you really need to be able to control the duty cycle, to get as short of an on-time as possible

    Thanks, mr.clean, for that bit of information.

    Bi-toroid Transformer Sayings

    One thing is you really need to be able to control the duty cycle, to get as short of an on-time as possible.The DC input current doesn't change with and without a load.Test of Bi-Toroid Transformer (BiTT v2.1) powered in DC - YouTube

    If anybody wants to add, please feel free.

    Regards

    Berg

    Leave a comment:


  • zolgar
    replied
    Driver Coils

    The matter of generating AC energy transfer with a dual stranded input configuration, by comparison with a single coil being switched in two directions. There are less switches; the potential of each coil builds with instant voltage supply.

    Leave a comment:


  • mr.clean
    replied
    Originally posted by SunofFather View Post
    I try this setup, but not with sine, with square to primary on who parralel capasitor. Seems no more out than you put in.
    i find that a single positive square pulse can only go so far before the core is saturated, the Mazzilli push-pull circuit worked well, but in tuning a pos and neg pulse h bridge worked best.

    one thing is you really need to be able to control the duty cycle, to get as short of an on-time as possible

    Leave a comment:


  • SunofFather
    replied
    I try this setup, but not with sine, with square to primary on who parralel capasitor. Seems no more out than you put in.
    Attached Files

    Leave a comment:


  • zolgar
    replied
    Ferrite BiTT, MEG Driver Circuit

    Hi Mr.Clean, This new demonstration is quite interesting. It appears there is more than meets the eye to your transformer design; internal construction techniques which have apparently produced a working effect. The core thicknesses do not seem to be altered to effect permeability. Thanks for sharing, I would like to suggest all kinds of new experiments with plenty of meters all over your device, but I am sure that you are well aware of how to show the details of output energy loaded, input energy loaded and unloaded etc.

    There is one specific thing I would like to ascertain - how well it produces light with a 12V filament type bulb.

    Leave a comment:


  • mr.clean
    replied
    hi all, been busy but i wanted to try the JLNaudin MEG circuit on the Bitoroid, pretty good, so im gonna do some more experiments soon...

    BiToroid Resonant Driver: MEG Circuit - YouTube

    Leave a comment:


  • gyula
    replied
    Hi kavkav,

    Okay for the answers. In the lab can you have access to a capacitor selector "box"? like shown here Build a Resistor/Capacitor Selection BoxOTTAWA UNIVERSITY - BI-TOROID DEMO July 11, 2009.mov - YouTube and for instance Naudin also tinkered with bi-toroids: Full measurements and tests on the Thane C. Heins' BiTT v1.5 (Bi-Toroid Transformer) - YouTube


    Greetings, Gyula

    Leave a comment:

Working...
X