Stingo Solid State Battery Charger

[sucahyo]

So what is the best for health on circuits including stingo and JT to make it to lower frequency? But when doing this it gives less BEMF I noticed. Although it's true I experienced that in low frequency batteries charge better.
Thanks

Not frequency, but signal sharpness, abrupt switching, fast signal fall time. I believe joule thief produce headache because of dull switching.

My corona maker run under 1000Hz, my sleeping aid run between 2KHz to above audible, it still produce nice feeling...

Adding connection to a bucket of water also help. Must not connected to ground. Connect it to output positive. This will not only produce more good effect for health, this also increase circuit output.

I don't know what you mean by less BEMF, I found that there is sweet spot, where the circuit have the best COP. So I always tweak potentimeter to get max output. Is not always at the minimum or maximum, it is usually in between.

[Guruji]

I and Godfrey had attached stingo on our bed everynight for the last few months now. For sleeping aid.

I am certain that I can use stingo to produce headache too. It change with how you connect the secondary, or where you connect terminal . If you seen my last stingo motor video, that is also an attempt to produce extreme headache, and it did if I turn it clock wise. Not for free energy research though.


I agree with 7imix about coil can change result. For the past few weeks I have been trying various coil to try to get the result I first get for sleeping aid use. Then I give up using toroid and use my first coil. A 12V-0V-12V/240V transformer. with the 240V part shorted. My soon sleep in minutes lol.
.

So what is the best for health on circuits including stingo and JT to make it to lower frequency? But when doing this it gives less BEMF I noticed. Although it's true I experienced that in low frequency batteries charge better.
Thanks

[sucahyo]

Hi guys JT is said that it emits RF does Stingo emits these frequencies? cause certain persons feels headaches with these.
Thanks

I and Godfrey had attached stingo on our bed everynight for the last few months now. For sleeping aid.

I am certain that I can use stingo to produce headache too. It change with how you connect the secondary, or where you connect terminal . If you seen my last stingo motor video, that is also an attempt to produce extreme headache, and it did if I turn it clock wise. Not for free energy research though.


I agree with 7imix about coil can change result. For the past few weeks I have been trying various coil to try to get the result I first get for sleeping aid use. Then I give up using toroid and use my first coil. A 12V-0V-12V/240V transformer. with the 240V part shorted. My soon sleep in minutes lol.

Now that you mention that, with the stingo slayer exciter I felt some headache, but a couple hours after "I left the building" so I didn't thought they are related....

The way you connect the HV part really concern me:
"one end of the L2 coil to the base of the NPN transistor."

I consider that connection may produce headache. I will prefer to connect on end of L2 coil to the positive of source battery. This is my feeling when I did experiment with car coil as corona maker.

While I still had 12V battery, I run stingo on my office as long as the battery last for two weeks. 4 of my friend mention good smeel, good feeling. There are mass flues infection that time. Seems to not infect my part . If the corona maker was durable, I would keep using it.


Stingo or any other electronic circuit can produce good and bad effect, please be carefull.

I plan to use a stingo with it's transistors mounted on this heat sink- And pulse a car coil, then put the HV through the 13 turn primary around the base of the tower.Bottom wire from the tower will go to ground the top one should be hot. For lights. I hope.

http://9xhe3g.bay.livefilestore.com/...001.JPG?psid=1

That is nice . Will look forward for your result .

sine wave/square wave...Sucahyo dont you know i do not have oscilloscope ?

I know, my point is I read that some UPS manufacturer boasting that their line up produce better sine wave. I forget why that is necessary.

electric iron ? no, i thought i should try it on my solder iron since i use the most often 15 W solder iron, and 15 W is also value of that testing bulb in my pictures...

But i suppose electric iron is a big consumer, what do you expect of that
specific experiment ?

I read that heater work best with AC. Maybe inverter with square wave will produce much greater heat than sine wave. your solder is better test I guess, because there is no thermostat there.

See if you can compare the heat too... thanks .

[cikljamas]

Plenty .

That make me reminded to previous question about sine wave and square wave output. What kind of electric appliance require sine wave? Have you try it on electric iron yet?

sine wave/square wave...Sucahyo dont you know i do not have oscilloscope ?

electric iron ? no, i thought i should try it on my solder iron since i use
the most often 15 W solder iron, and 15 W is also value of that testing
bulb in my pictures...

But i suppose electric iron is a big consumer, what do you expect of that
specific experiment ?

Hi Guy's, Here is a pic of a rough tower coil I whipped up last night. It has three joins. I made it from an old quadfilar coil. If it works good i'll wind a much better one.

http://9xhe3g.bay.livefilestore.com/y1pb-UnJEcFCsmnV25ym7dHXVtBih4Ta6mFO6_6thLOB-DpRDBSxEkx4n1hHNA-Tc79Ls4zwev3PtXhYQCjdXnF6MoRdUWzEg5A/Tower%20coil%20001.JPG?psid=1

It's 450 turns .5 mm wire The primary is 13 turns 1 mm wire I have two of those if I need them.

I plan to use a stingo with it's transistors mounted on this heat sink- And pulse a car coil, then put the HV through the 13 turn primary around the base of the tower.Bottom wire from the tower will go to ground the top one should be hot. For lights. I hope.

http://9xhe3g.bay.livefilestore.com/y1pR31pAMvdWvV_kTf0pvaoJBzsrW_dQbHQxHdhM9lYpfn0iC2WZkX9KrW5T0NnTbhrbORm3xnUP_xquFWaS16RqWZn9FuQFskK/Stingo%20Heatsink%20001.JPG?psid=1

Hope to build the Stingo tonight.

Cheers

Farmhand i am anxious about the results of your announced experiment !
Inform us about it as soon as you find out some usable infos !

Good luck with stingo assembling ! It should be easy and quick job since it
is very simple circuit !

Cheers !

[Farmhand]

Hi Guy's, Here is a pic of a rough tower coil I whipped up last night. It has three joins. I made it from an old quadfilar coil. If it works good i'll wind a much better one.

http://9xhe3g.bay.livefilestore.com/y1pb-UnJEcFCsmnV25ym7dHXVtBih4Ta6mFO6_6thLOB-DpRDBSxEkx4n1hHNA-Tc79Ls4zwev3PtXhYQCjdXnF6MoRdUWzEg5A/Tower%20coil%20001.JPG?psid=1

It's 450 turns .5 mm wire The primary is 13 turns 1 mm wire I have two of those if I need them.

I plan to use a stingo with it's transistors mounted on this heat sink- And pulse a car coil, then put the HV through the 13 turn primary around the base of the tower.Bottom wire from the tower will go to ground the top one should be hot. For lights. I hope.

http://9xhe3g.bay.livefilestore.com/y1pR31pAMvdWvV_kTf0pvaoJBzsrW_dQbHQxHdhM9lYpfn0iC2WZkX9KrW5T0NnTbhrbORm3xnUP_xquFWaS16RqWZn9FuQFskK/Stingo%20Heatsink%20001.JPG?psid=1

Hope to build the Stingo tonight.

Cheers

[7imix]

slayer coil is not bifilar coil...

I know. I was just testing for my own curiosity because I had not tried before.

[sniky]

slayer coil is not bifilar coil...

[7imix]

Nope, it's not possible to oscillate a bifilar coil, at least with my limited testing. Not enough inductance.

[sniky]

It depends on the coil. I have only seen up to about 30khz with my power stingos. I saw higher frequencies with my low power stingo.

It also depends on the geometry of the coil. A standard helix coil would be the worst for rf, a toroid sould be better, a bifilar toroid might be the best, if it's possible to oscillate a bifilar coil. I should try.

You should build experiment and see if it gives you a headache... Mine never have.

Now that you mention that, with the stingo slayer exciter I felt some headache, but a couple hours after "I left the building" so I didn't thought they are related....

[7imix]

Hi guys JT is said that it emits RF does Stingo emits these frequencies? cause certain persons feels headaches with these.
Thanks

It depends on the coil. I have only seen up to about 30khz with my power stingos. I saw higher frequencies with my low power stingo.

It also depends on the geometry of the coil. A standard helix coil would be the worst for rf, a toroid sould be better, a bifilar toroid might be the best, if it's possible to oscillate a bifilar coil. I should try.

You should build experiment and see if it gives you a headache... Mine never have.

[Guruji]

JT and Stingo

Hi guys JT is said that it emits RF does Stingo emits these frequencies? cause certain persons feels headaches with these.
Thanks

[7imix]

http://www.energeticforum.com/renewa...tml#post126842

Thanks for posting a link to this, I have a hard time keeping up with the volume of posts in that thread. I will try.

[sniky]

http://www.energeticforum.com/renewable-energy/4999-joulethief-sec-exciter-variants-51.html#post126842

[sucahyo]

Welcome !
How many thanks for this picture (result) ? :
http://img72.imageshack.us/img72/844...5wnewresul.jpg

Plenty .

That make me reminded to previous question about sine wave and square wave output. What kind of electric appliance require sine wave? Have you try it on electric iron yet?

I am not sure about this issue, i just saw some very quick switching circuits, and it came to my mind that this could be the reason why we did not come closer to our ultimate goal OU...

Relatively same question is posted on ferris wheel, here is Bedini's answer.

The reason for the low current is allow for the highest possible Radiant Energy that is found in all space that surrounds you, some call it, Radiant, negative energy, special charges and so on, but it's all the same thing. This energy is scattered vectors pointing everywhere thought-out space.

I wonder if I do it unconciously lol, why I choose to use many stingo at low power than one at high power. I know that I can produce 700mA output with just one, and yet I choose three to produce them....

The cap dump technique also dump the charge at "slow" rate of 2 seconds each.

[cikljamas]

Many thanks for that . Interesting voltage and amp reading...
.

Welcome !
How many thanks for this picture (result) ? :

http://img72.imageshack.us/img72/8441/inverterbulb15wnewresul.jpg

Why it has to be fast? Bedini ferris wheel rpm is slow, and he mention us to slow down too...

I am not sure about this issue, i just saw some very quick switching
circuits, and it came to my mind that this could be the reason why
we did not come closer to our ultimate goal OU...But if you say this is
the better way, i believe you...

Cheers !