Donald Smith Devices too good to be true

[med.3012]

Hello Dwane
Hello everyone

i will post the most recent update regarding this subject ..
the first thing i noticed is the impact of ETBC layers order




here is the detail of ABCD positions of the two ETBC :




the following drawing show the correct path to take the power ... in reality we have to take the shifting magnetic domain movement so the system see nothing you take as the previous experiment above ( even i didn't make it very well )

[Dwane]

here are photos

Photos did not upload.

How do I clear old uploads? Cannot see a link

[Dwane]

Quick test set up

Hi guys,
Here is a quick setup for the above discussion. Most likely guaranteed not to fail!. I have ETBC tx wound on ETBC rx approximately 4:1, more like 5:1! Shooting from the hip so to speak. The closer the SG the more illumination. The faster the SG frequency the brighter to globe. LED Globe 220-240 volts ac 6.5watts rated. Photo shows double ETBC, setup, globe alight. Double ETBC is one ETBC wound on top of another. Other photo shows Frequencies of SG.I have had a few goes at this, lots of LED reaction, not much else. YET!

I am getting about a 2:1 amplification with signal strength.

Regards

Dwane

[Dwane]

ilandtan

i am not Obscuring the real genius of people like Tesla, i am developing something i feel but i can't see , first of all the ETBC can pump an extra charge through the capacitive extension ... i explained this several time but let see something



it's possible to take the power through double ETBC wound in a ferrite core where normally there's an opposite magnetic flux !!!



power consumption is nearly zero when the LED is on

i don't know if this is what we are looking for or no , please explain ..


regards

Hi Med,
I would just like to say something about the use of LED's in showing overunity. From all the various demonstrations out there showing overunity effects using LED globes or material, I think what we are looking at here is a specific frequency response to the semiconductor material and its doping. Showing an electric motor driven would be a better argument when demonstrating overunity.

Have a good New Year to you all.

Dwane

[ilandtan]

Hi !

the most important is the moment when your system change to be a real open system .. this can be seen in the slow waves ( like AM wave ) .
The energy enter the system like a modulated signal as a result from magnetic poles shifting as
explained before :



for sure we need to tune the device but the key is the type of induction ( attraction ) this can happen easily using two ETBC.

Well it sounds easy. But can you easily show us something to say it's a worthwhile direction? Like a working device?

[ilandtan]

Hi ilandtan,

lightning is over unity but there's no resonance involved , now we have two ETBC's work together not a simple wrapped capa /coil

Hi Med,

Lightning is a discharge from one plate to another. The whole idea is that the charge separates, and you create a potential. There are steps to make lightning usable. Tuning is one of them. You can say it - that tuning doesn't matter, but I disagree.

[med.3012]

Hi Med,

I have to admit to you my truth. I have not found any gain from input to output in a single device configuration. That's why I think you can try any combination of the EBTC and it will not break unity.

I suspect because you have a capacitor and coil wrapped up into one device, you have never achieved a resonant device. I think the tuning the device is crucial. Tesla knew what he needed to tune to, and so did DS.

Have you created a resonant EBTC?

Hi ilandtan,

lightning is over unity but there's no resonance involved , now we have two ETBC's work together not a simple wrapped capa /coil

[ilandtan]

Hi Med,

I have to admit to you my truth. I have not found any gain from input to output in a single device configuration. That's why I think you can try any combination of the EBTC and it will not break unity.

I suspect because you have a capacitor and coil wrapped up into one device, you have never achieved a resonant device. I think the tuning the device is crucial. Tesla knew what he needed to tune to, and so did DS.

Have you created a resonant EBTC?

[med.3012]

ilandtan

i am not Obscuring the real genius of people like Tesla, i am developing something i feel but i can't see , first of all the ETBC can pump an extra charge through the capacitive extension ... i explained this several time but let see something



it's possible to take the power through double ETBC wound in a ferrite core where normally there's an opposite magnetic flux !!!



power consumption is nearly zero when the LED is on

i don't know if this is what we are looking for or no , please explain ..


regards

[ilandtan]

Med,

You use this diagram for Tesla, and it is my opinion you are using this out of context. What that diagram is stated for wireless transmission, and you are linking it together to your multi layered device for over unity.

I'm starting to think you are a misdirection craft member. Obscuring the real genius of people like Tesla. His devices, used two important elements, the damped waves from ultra-fast capacitor discharges, And the Earth as an elastic cavity resonator, to produce magnetic feedback.

There is no single device that creates the "magic" in that process. This EBTC is a red herring. I've read your explanations of its inner works, but you forget the obvious, it doesn't give you the advantage of a Bi-filer Tesla Coil, because it doesn't have the geometry. If you show an experiment where gain has increased, please let me know, I don't claim have an answer, but I can plot a walk in the Sahara for me.

[ilandtan]

Clear pictures from the Donald Smith video`s . Thanks to Rick Friedrich who somehow has a lot of Don Smith material.

Here from his video are the clear ilustrations https://www.youtube.com/watch?v=dICbnzfY464#t=253

For years I have watched these video`s from Don where he showed these pictures, ilustrations.

1994 https://www.youtube.com/watch?v=BHr3eDELyHk#t=636
1996 https://www.youtube.com/watch?v=INPIfDGfMGs#t=3724

He says the ilustrations explain why overunity is possible.

Can somebody maybe explain it better …
and Rick where did you find these clear ilustrations ?

Hey Bro,

That wave is from a book, and if you find that book you got the picture Page 27 Here
Negative resistance is exhibited in certain devices where they operate in a certain range. I think a tunnel diode is one .

The DS ground shunt aka negresister has also been explained to me another way in energyevo.com look for posts by dynatron.

To me, it looks like you are somehow bringing in outside energy. How else can a wave increase in current and voltage? That's why my theory is a bit different on what it's doing.

[med.3012]

[med.3012]

Hello everyone ,

since a long time someone asked me about the 4 layers Don device, here is the answer
from Don himself !

https://youtu.be/S1TtBsCoLsA

[Dwane]

Don delay pulse

Hi guys,
Here is my latest wind CW and CCW, in the photos attached I am seeing a delay of about 200ns. The only thing that worries me is the small starting pulse on the blue waveform. A copy of the adjacent starting coil? The pink waveform is from the CCW coil Blue is from CW. Waveform a bit messy at the start but cleans up.

Regards

Dwane

[Dwane]

Don problem

Just before I disappear, here are a couple of photos showing CW and CCW difference using Don's 2 turns!! Not sure how this was supposed to provide the necessary offset that he says we are looking for. To my mind the critical starting point for the waveform should have been offset. I am using two magnetic pick-ups, with input to L1 10Kv.

Regards

Dwane