Imhotep's Radiant Oscillator Video

[Soldyur]

Thanks

Agongon,

I appreciate that. I am going to print it out and begin construction with a competent electrical amigo. Saves me from bothering you guys with dumb questions, so that you can spend your time saving the world!

Jason

[DavidE]

Results #2

Same set up as before... but eliminated the batteries.

Utilized a 500ma 12v dc power supply (Chinese plug in the wall variety)

Actual output of power supply +15.4v.

Power measurement at cathode (charging side) +97v.

Removing earth ground causes it to read (at the same place on the cathode) +64v.

All measurements on the 200v DC scale.

Steady state power supply seems to have stabilized resonant frequency.

So here is my novice question. Are these effects truly radiant or are we reading results more consistent with some kind of typical coil/magnetic field transformer effect?

[Bodkins]

Bodkins

I watched your youtube video but thought that I may search
for similar effects with the lv SSG. Here is what I found.

I built a standard SSG, orginal schematic Imhotep/Bedini.

12v 7a Primary battery
(2) 6v 4a Charge batteries hooked in series

I disconnected the positive lead going to the charge battery (the one with the diode).

I spun the fan to start resonation and turned the pot until the fan stopped spinning, but kept up its resonant audible pitch.

1st test. I tested voltage (dc) on the anode side and got a +2.2v and with a little twist of the pot I could adjust up to +2.9v Note: if you go too far out of the resonant range with the pot, it will quench the resonation and you will need to re-start it. (these actual numbers will vary based on type and condition of the power source that you are using)

2nd test. I tested the voltage on the cathode side (the side that would normally be hooked to the + on the charge battery) it read +36v. Hmmm. I then connected an earth ground to the cathode side and the voltage went up to +43v. This is without it being attached to the battery.

3rd test. Once earth ground is attached, and your voltmeter probe is still connected to the cathode side of your diode... touch various parts of your circuit and notice which parts of it produce a favorable rise in voltage, or the opposite. In fact you can even touch the insulated wire on your hooked up voltmeter, voltage increases! Very strange.

An earth ground (or something about that type of effect) seems to make certain parts of the circuit open to atmospheric flow or promote some kind of radiant properties. Where the earth ground is best placed in the circuit is open to further work. I must admit that I noticed Bedini's earth ground symbol on his simple SG circuit but at the time didn't bother exploring it's benefit.

Bedini's SG


Bodkins... working with the hv circuit, got frizzy hair yet >


If any of you have questions (I have millions) be gentle, I have the electrical IQ of a 10 year old.

i played with the sg and had wired stuff(meterreading) when connecting to differect parts it a long time ago BUT checkout the earth battery thread i have posted it in this thread somewhere look back and please put it forward it important for understand the gas/water flow of the Energy.
everyone need to read it.
On you electrical iq dont worry its higher than mine!!!
watch the next video for my hairline

[nat1971a]

Hi All,

I was thinking last night about what bodkins was saying in his video about it pulls in negative at a certain frequency and positive at another frequency. And then it hit me, this sounds like Tesla's pierce arrow electric car theorised design i looked at some time ago.

If you look at the attached image (for the series connection) theres positive energy on the left and negative energy on the right of the AC motor. In the text where i found these diagrams there is mention of two aerials on top of the car.

This is a huge guess and leap of faith but as Tesla would say "see the excitement coming"

Cheers

Nat

[Bodkins]

Same set up as before... but eliminated the batteries.

Utilized a 500ma 12v dc power supply (Chinese plug in the wall variety)

Actual output of power supply +15.4v.

Power measurement at cathode (charging side) +97v.

Removing earth ground causes it to read (at the same place on the cathode) +64v.

All measurements on the 200v DC scale.

Steady state power supply seems to have stabilized resonant frequency.

So here is my novice question. Are these effects truly radiant or are we reading results more consistent with some kind of typical coil/magnetic field transformer effect?

i think if you pulse a transformer you will get this effect! so is it typical i dont now?

[Bodkins]

and another video
YouTube - YouTube - Bodkins Free Energy Radiant Oscillator Cap Chargin
got one after this too!
nat1971 the second your going to love it,lol

[Bodkins]

The thing we need to determine now is...........

Can the circuit get nailed down and stabilized, so that it will operate at the flip of a switch, without requiring the attention of periodic tuning.
Since the radiant waxes and wains, it will probably cause drift. Maybe some kind of circuit can be built that will indicate when she is singing the right note. Or to be more exact....."The choir is singing in Harmony"


Carl

i can tune it, switch off the power.
switch it back on and it start going with no ajustment.
which is a start

[Bodkins]

AC

when you get the effect switch meter to ac its is higher.
I dont now about this stuff but is ac/dc same on a volt meter.
i mean the same reading off one source?

[Bodkins]

I need sleep.
YouTube - Bodkins Free Energy Radiant Oscillator flow dirrection
Good luck all

[ren]

@bodkins

You are correct a ground is not required. When you consider the qualities of the current utilized it should become obvious that the energy transfer is based on "surface area"---capacitance. You are not "lighting" the cfl with an electrical current persay when using a one wire setup, how could you? The high potential currents seek a lower potential in any form it can find, this form can be the extended surface area of the ionized conductive gasses of the clf. Your ground is the space surrounding any conductor, the extent of the ground is based on surface area, but we have to let go of this silly concept of ground. A better option is the "source" and "sink" relationship which uses relative terms, a sink is a condition of matter or space which has the ability to expand the compressed condition of the source. In expanding the source its potential has been lowered and this is the reason energy is directed towards the sink. It should also be considered that a conductive rod buried in the earth, a ground ,can be a source or a sink depending on the qualities of the currents imparted to the grounded conductor. The frequency of the currents also plays an important role, if energy is stored in the space surrounding a conductor (the sink) then when the source is removed this energy in the sink becomes a source in itself relative to any other lower potential and a reversal of flow can occur. So at any given potential, inductance and capacitance there is a natural rythm of give and take which exists, if the source is not in sync with this natural rythm inefficiencies and losses occur. I hope this helps to simplify things.
Best Regards

Hello mate, good to hear from you (Listen to every thing that this chap has to say guys )

So AC, if these "currents" are seeking a lower potential this can be in the form of surface area. The potential that builds up will seek equilibrum by sinking itself into whatever it can?

In my particular setup I have the HV center connection of one ignition coil hooked up through the light to the other HV terminal on the other coil. If the two igniton coils primaries are wired in paralell the light wont come on, however if in series I get my highest light for no extra amp draw, even a slight decrease in draw. I was wondering why this was so. Are the two coils out of phase? Or can HV sink into other HV? I note that if the Ignition coil is connected to the light and then the other terminal is sinked to the negative of pretty much anything, including a cap with nothing else on its terminals. Infact it will sink into the positive of the battery too.

Thanks for joining in AC

[DavidE]

Bodkins

Bodkins said: i played with the sg and had wired stuff(meterreading) when connecting to differect parts it a long time ago BUT checkout the earth battery thread i have posted it in this thread somewhere look back and please put it forward it important for understand the gas/water flow of the Energy.
everyone need to read it.

http://www.energeticforum.com/renewable-energy/2209-earth-battery-sg.html

[sirmikey1]

I am watching the Hutchinson Effect Videos, and his research is
showing that levitation, decomposition, and transparency of matter
is normally occurring at around 22 to 24 centimeter waveband, which
is UHF.

television broadcasts, microwave ovens, mobile phones,
wireless LAN, Bluetooth, GPS and Two-Way Radios such as
FRS and GMRS Radios

Explains the invention of the microwave. Hack the magnetron?

SM

[DavidE]

Current Flow

Ok, will someone help me with a simple explanation for this effect???

Diode on the charging circuit anode side has 2.9v, at the same time 43v on the cathode side.

Second set up, the diode has 10v on the anode side 97v on the cathode side.







I thought that i understood what a simple diode did... now I am not sure.

Diode-Function of a diode is to allow an electric current to pass in one direction and to block it in the opposite direction.

[ashtweth]

Agongon and Ren thanks for the Schemo 's it makes the documentation so easy and avoids newbee's Q's updating now.
Bodkins, thats some freaky stuff amazing, lol Agonon just saw the bit about Bodkins house ...

[Bodkins]

Hello mate, good to hear from you (Listen to every thing that this chap has to say guys )

So AC, if these "currents" are seeking a lower potential this can be in the form of surface area. The potential that builds up will seek equilibrum by sinking itself into whatever it can?

In my particular setup I have the HV center connection of one ignition coil hooked up through the light to the other HV terminal on the other coil. If the two igniton coils primaries are wired in paralell the light wont come on, however if in series I get my highest light for no extra amp draw, even a slight decrease in draw. I was wondering why this was so. Are the two coils out of phase? Or can HV sink into other HV? I note that if the Ignition coil is connected to the light and then the other terminal is sinked to the negative of pretty much anything, including a cap with nothing else on its terminals. Infact it will sink into the positive of the battery too.

Thanks for joining in AC

this is were it gets difficult for me to get my point across ren
first i need to clean this up two hv going to the bulb yes?if so one has lower sink because lower energy from battery in series ignition setup.
i dont now if you can connect a meter to the bulb negative to see direction flow you may fry it, if too much hv. but i think its pushing out so you can connect it to anythin without light going off.
If it was pulling in the light would go out,I think!
one more thing i have had multipill branches to the sink!
I also see it as a pump in fact i see all sg ssg imhotep fans tesla's radiant energy device as pumps.
hope this helps