Free Energy At Last Step By Step Must See

[**~Imhotep~**]

ohms is extremely low my coils had 30 to 60 ohms dc resistance if all of your parts are good and wired correctly ,the low ohm could be you problem ,if you wound them yourself you might try smaller wire and more turns per pole, the stator picture is deceptive the windings should go continuous cw ccw cw ccw all the way around the stators pole all four,continuous dual wind ending up with four wires, then ran to the 4 positions on the picture. do not give up i have done many of these all successfull you will also let me know if you still have problems .i will help you!

[Tehnoman]

So, finally I managed to complete my circuit, but it doesn't work. Can't figure out why. All connections is ok, diodes is in right direction, 2N3055 is functional and connected as well. Variable resistor configured to 2 Kohm. Only neon is ~ 60V AC rated, because thought that firs time I won't be able to get spikes as high as 100V. And I was true. Couldn't get any spikes at all...

I have two thoughts. First - it could be that my PC fan rotor magnets are too weak to trigger transistor. Tried to measure induced voltage when spinning fan with my hand, couldn't get more than 30 mV. But that could as well not be the case, because my multimeter may not show the initial voltage spike.

Second - maybe I didn't understand fan wiring after all? I connected it so when both coils are connected to + and - PSU terminals. And my magnet indicated that the stator coils showed NSNS configuration. Isn't that right?

[..]

[..]

Btw, coils are wired cw-ccw-cw-ccw, they are bifilar, each wiring has 7 ohm DC resistance, bifilar together - twice as low, two coils together - twice as much and so on.

[**~Imhotep~**]

no fe invention will escape my investigations ,over time we will together solve these mysteries . today aug 1st we will try replicating the oscillator yay!!!

[boguslaw]

you are absolutely correct Aaron ,me and Peter worked on his hypothesis and he instructed me on the proper use of the kill-a-watt meter and proved to me what he was talking about. we are being mis informed on the actual billing of our power when it comes to energy saving cf bulbs . they appear to be billing us for approximately twice as much as the advertised wattage on the deceptive packaging . peter has suggested a work around for the discrepancy and i am experimenting with the values we can use to resolve the issue. the meter can be purchased at harbor freight tools for 20 $ and the procedure will be posted on my website Imhotep's Laboratory | Renewable Energy soon . as well as this forum. there are many other units in your home and business that will benefit from this investigative procedure you all owe Dr Peter Lindemann many thanks for his tireless work and unending and infinite wisdom

Ok.Now we need a small generator, probably TPU to power all light in house. Brilliant idea !

[**~Imhotep~**]

you are absolutely correct Aaron ,me and Peter worked on his hypothesis and he instructed me on the proper use of the kill-a-watt meter and proved to me what he was talking about. we are being mis informed on the actual billing of our power when it comes to energy saving cf bulbs . they appear to be billing us for approximately twice as much as the advertised wattage on the deceptive packaging . peter has suggested a work around for the discrepancy and i am experimenting with the values we can use to resolve the issue. the meter can be purchased at harbor freight tools for 20 $ and the procedure will be posted on my website Imhotep's Laboratory | Renewable Energy soon . as well as this forum. there are many other units in your home and business that will benefit from this investigative procedure you all owe Dr Peter Lindemann many thanks for his tireless work and unending and infinite wisdom

[Aaron]

power factor correction

Imhotep,

I'm glad you're working on PF correction. Everyone should get a Kill-a-Watt meter. They'll see very quickly how they're being conned by the industry. We don't pay for what we're told we pay for.

[**~Imhotep~**]

without seeing the coil structure its not easy for me to advise on the wraps , but the way most fans were wrapped is as follows =three posts, one post has two wires on it , you separate the one post that had two wires on it and place one of the two wires on an additional post you provide in the 4th post position that is on the stator then solder the second wire back on the original post that had 2 wires originally on it and then check for continuity between the 4 posts and most likely you will end up with two sets of coils ,one for trigger and one for power . if you still have problems you can check out my website and get more detailed instructions at Imhotep's Laboratory | Renewable Energy

[gunfighter]

Wraps.... totally messed up the wraps. My daughter and I are building one of these together, and I misunderstood the part in the video about the coils. Based on the diagram I found here on this post, I ended up connecting each coil to its own post and disconnecting the adjacent coils. Do I need to go back and re-wrap from scratch or is there any way to reconnect the + and - coils?

[**~Imhotep~**]

i did not use ssg's to power the radiant oscillator but the ssg can be used in aarons water spark plug to charge the cap in a few seconds isolated .i have previous commitments and am being stretched thin so i have not been able to complete his experiment yet .also a power correction circuit will emerge for the cf bulbs to get the real power savings as revealed by Dr. Peter Lindemann

[energeist]

Hi Imhotep

found your website. And with that the answers to my question!

Imhotep's Laboratory FAQ • View topic - Schematics

[energeist]

First try

Hi Imhotep,

as so many I have watched in awe radiant energy applications being discussed on this forum for a while now, however that I would get the chance to build one for myself I had no Idea. You made it happen! I bought the components and I started assembling the circuit today

I modified the stator, yup I learnt soldering and so far it looks right. I know I have alot of reading to do and I try not to bothre you with unnecessary questions. However I have problems comprehending the circuit when it comes to attaching the batteries. Do you have a blueprint other then the one shown in your 4 part video instructions so I can print it out and study it properly?

Anyway, thank you so much for your devotion, you made me trust in my thumbs again

my regards to shiva!
rvg

[WoollyNZ]

Many Thanks

I haven't achieved my ultimate goal of running the shed off the grid.

But I have achieved control over my own destiny. This is more important than anything else.

Many many thanks to Imhotep, Shiva and everybody else.

[**~Imhotep~**]

Hello All,

Shiva has been working really hard on getting the site together. We have a special section called a Interactive FAQ and in it we have it separated for each of the projects I have released and will be releasing. For everyone who has built the Imhotep-Bedini fans we would like to see your master pieces! She has created a special section for everyone to show off their work.
You can go here and post pictures of your fans and circuits. We cant wait to see your fans!

[InTheField]

In the attached picture I have attempted to show my naive placement of 2 extra components. As the Mosfet starts to conduct the voltage across the resistor & TVS diode in parallel will rise. No current flows via the diode until the breakdown voltage is reached. At which point the diode voltage will drop dramatically and the inductor voltage rise dramatically, ie peak at warp speed, hopefully. Would this work?

Maybe I should just wait until August 1st, hehehe...

Buccaneer

Hi Buccaneer,

The schematic you have attached shows the same setup from page 7 of the D14.pdf document concerning Dave Lawton's Meyer's Replication. The main difference is that the zener diode isn't shown in the Lawton circuit (but has been discussed on these forums before, including the reason for using it) and the bifilar inductor is connected differently in order to get some reverse current power to flow into the cells. The other addition that I (and others) have made (which has also been discussed on the forums here) is adding a diode before the bifilar path going from the MOSFET to the cell. That's to prevent the reverse current from going back to the FET and actually creates two spikes (one from the FET, the second from the reflection/reverse).

Good Luck,

ITF

[Buccaneer]

Hi,

I'm new around here but very interested in this forum. I have built 2 brute-force Hydroxy generators (using an open-bath series design) but from reading many of the posts I can see that I'll need to use some sort of radiant/resonant design to get more gas production. Now, I'm no EE but I do have a few clues about circuits and the core principle seems to be pulsing a coil with very sharp voltage spikes. The circuits from Meyers onwards all seem to use the 555 timer but the max frequency for those chips is a few MHz. However, while looking at a wikipedia article about diodes
( Transient voltage suppression diode - Wikipedia, the free encyclopedia )

I found this document about Transient Voltage Suppression (TVS) diodes:

http://www.st.com/stonline/products/literature/an/5628.pdf

Figure 4.d shows the voltage across a Trisil device and the voltage peaks look really really sharp - Ouch! Since the reaction time of TVS is about 1 ps (1 millionth of 1 microsecond) is there some way of using this behaviour to cause very sharp spikes?

In the attached picture I have attempted to show my naive placement of 2 extra components. As the Mosfet starts to conduct the voltage across the resistor & TVS diode in parallel will rise. No current flows via the diode until the breakdown voltage is reached. At which point the diode voltage will drop dramatically and the inductor voltage rise dramatically, ie peak at warp speed, hopefully. Would this work?

Maybe I should just wait until August 1st, hehehe...


Buccaneer