Oscillating Reed Switch Pulse Motor.

[Allen Burgess]

LC resonance.

The coil wrapped Reed switch oscillator of George Chaniotakis, can couple nicely with the (Auxilliary High Voltage LC Tank Flyback Pulse Coil) of Woopjump. The Reed switch oscillator runs at 16 KHz, so the self resonating frequency of the (High Voltage Auxilliary LC Tank Pulse Coil) needs to be tuned to the same frequency. This involves the well known resonance formula everyone enjoys playing with, matching Ohmic resistance to Farads.

This circuit consists of five componants: The Reed switch and surrounding 250 Ohm coil; A fast switching diode in series with a high voltage ferrite core auxilliary power coil and matching capacitor. The oscillation would be controlled with a biasing magnet as Chaniotakis demonstrates. This circuit would perhaps consume 3 milliamps and potentially accelerate our frictionless rotor to nearly a million RPM's! The power coil would drive the diametric rotor as a (Synchronous A.C. motor).

Output would need to come from induction. I may upload several videos from Neatpete45, to demonstrate how harvesting radient backspike kills induction. There'ed be no problem drawing "Lenz Free" output with an Avmarenko plug. It may be able to self loop this way!

All the current from the Reed switch oscillator needs to do is replenish the tiny amount of current lost to reistance in the auxilliary pulse coil LC tank! One can see how this setup places the Reed oscillator behind the oscillating coil, and uses the High voltage coil tank resonance to power the diametric rotor instead of oscillating the up front Reed switch like Herr Segelohrenbob and Simplefix 2969 do.

The essential component is the frictionless, levitating bearing. The precision ceramic bearings I presented at the start of the thread would function fine as well. The oscillation is too subtle to move an ordinary rotor. It requires a very powerfull magnet field and close to frictionless bearings to work.

[Allen Burgess]

flyback pulse coil.

Woopyjump's schematic for a "Flyback Auxilliary Pulse Coil" below shows a thin wire high voltage coil in parallel with a 1 microfarad capacitor, in series with a diode following the Reed switch. Cool Joule demonstrated how the addition of a capacitor creates a pulse from flyback too.

I wonder if these three componants can wire on to the "Very Simple Reed Switch Oscillator" above between the switch contacts in place of the LED, and power a magnet rotor with the "Flyback" like Woopyjump does?

Woopyjump has his Reed switch in series with the primary coil, the rest of the circuit would be practically Identical! The capacitor's the trick!

[Allen Burgess]

Simple Reed oscillator.

Interesting Reed switch oscillator approach. This is the same Radio Shack Reed switch I used. Are the contacts doing the switching at 16 Khz, or magnetic plasma? Could something like this power a frictionless, levitating magnet rotor at 960,000 RPM?


"Very Simple Reed Switch Oscillator" of George Chianiotakis can be "self oscillating". Only you need an axial inductor of 250 Ω resistance & Reed Switch inside the inductor an white Led DC3.2-3.4V 20mA 10mm Round. It is amazing to drive a super bright led only with 3ma but i would say that it is High Efficiency".

https://www.youtube.com/watch?v=ZKjj4x9zhvs

Here's an oscillascope shot of the Reed switch oscillator indicating 16 KHz at .6 volts:

https://www.youtube.com/watch?v=I24nDi_q-EU

There's a simple wiring schematic below: The positive lead from the battery goes to the beginning of the 250 Ohm coil then the end of the coil goes to the far contact of the Reed switch. There's a jumper between the two contacts of the Reed switch with the LED in between, then the near contact connects to the negative electrode of the battery.

[Allen Burgess]

LC resonance.

This "Reed switch oscillator" by Simplefix 2969, comes complete with a schematic at the end of the video. The Bedini essay above on Tesla stresses the importance of the capacitor. We see a 300 volt flash camera capacitor in parallel with a 23 SWG wire, ferrite core coil, of 300 to 400 turns, with a few backing magnets. The self resonating frequency of this LC tank drives the "Reed switch" into plasma pulse operation in series with a 1.5 volt battery:

https://www.youtube.com/watch?v=GfN5VfZdAPY

We saw Herr Segelohrenbob power a crude pulse motor with just this kind of "Plasma Reed Switch" at the end of his (Plasma Reed Switch Video) above! Everyone can see the awesome application for the bismuth axle, circular Halbach evacuated levitator rotor now! Herr Segelohrenbob has separated the oscillation from the magnet rotor, and we see a small biasing magnet replace the problematic Reed switch coil positioning headache my primitive setup creates. Looks like we're slowly but surely advancing into a futuristic pulse motor with impulses in 1.0 microsecond duration range.

[Allen Burgess]

Bedini on Tesla.

Bedini on Tesla:


"Through successive experimental arrangements, Tesla discovered several facts concerning the production of his effect. First, the cause was undoubtedly found in the abruptness of charging. It was in the switch closure, the very instant of "closure and break", which thrust the effect out into space. The effect was definitely related to time, IMPULSE time. Second, Tesla found that it was imperative that the charging process occurred in a single impulse. No reversal of current was permissible, else the effect would not manifest. In this, Tesla made succinct remarks describing the role of capacity in the spark-radiative circuit. He found that the effect was powerfully strengthened by placing a capacitor between the disrupter and the dynamo. While providing a tremendous power to the effect, the dielectric of the capacitor also served to protect the dynamo windings. Not yet sure of the process at work in this phenomenon, Tesla sought the empirical understanding required for its amplification and utilization. He had already realized the significance of this unexpected effect. The idea of bringing this strange and wondrous new phenomenon to its full potential already suggested drilling new possibilities in his mind. He completely abandoned research and development of alternating current systems after this event intimating that a new technology was about to unfold.

"WE do not need to do this with high voltage as it works on any level."

The effect could also be greatly intensified to new and more powerful levels by raising the voltage, quickening the switch "make-break" rate, and shortening the actual time of switch closure. Thus far, Tesla employed rotating contact switches to produce his unidirectional impulses. When these mechanical impulse systems failed to achieve the greatest possible effects, Tesla sought a more "automatic" and powerful means. He found this "automatic switch" in special electrical arc dischargers. The high voltage output of a DC generator was applied to twin conductors through his new arc mechanism, a very powerful permanent magnet sitting crosswise to the discharge path. The discharge arc was automatically and continually "blown out" by this magnetic field.

Imperative toward obtaining the desired rare effect, the capacitor and its connected wire lines had to be so chosen as to receive and discharge the acquired electrostatic charge in unidirectional staccato fashion. The true Tesla circuit very much resembles a pulse jet, where no back pressure ever stops the onrushing flow. Electrostatic charge rises to a maximum, and is discharged much more quickly. The constant application of high voltage dynamo pressure to the circuit insures that continual successions of "charge-rapid discharge' are obtained. It is then and only then that the Tesla Effect is observed. Pulses literally flow through the apparatus from the dynamo. The capacitor, disrupter, and its attached wire lines, behave as the flutter valve. ( The dynamo or the storage battery does the same thing with the correct switching)

Tesla found that impulse duration alone defined the effect of each succinct spectrum. These effects were completely distinctive, endowed with strange additional qualities never purely experienced in Nature. Moreover, Tesla observed distinct color changes in the discharge space when each impulse range had been reached or crossed. Never before seen discharge colorations did not remain a mystery for long. Trains of impulses, each exceeding 0.1 millisecond duration, produced pain and mechanical pressures. In this radiant field, objects visibly vibrated and even moved as the force field drove them along. Thin wires, exposed to sudden bursts of the radiant field, exploded into vapor. Pain and physical movements ceased when impulses of 100 microseconds or less were produced. These latter features suggested weapon systems of frightful potentials.

With impulses of 1.0 microsecond duration, strong physiological heat was sensed. Further decreases in impulse brought spontaneous illuminations capable of filling rooms and vacuum globes with white light. At these impulse frequencies, Tesla was able to stimulate the appearance of effects which are normally admixed among the electromagnetic energies inherent in sunlight. Shorter impulses produced cool room penetrating breezes, with an accompanying uplift in mood and awareness. There were no limits in this progression toward impulses of diminished duration. None of these impulse energies could be duplicated through the use of high frequency harmonic alternations, those which Sir Oliver Lodge popularized, and which later was embodied in Marconi Wave Radio. Few could reproduce these effects because so few understood the absolute necessity of observing those parameters set by Tesla"

"This unidirectional succession of charge-discharge impulses causes a very strange field to expand outward."

[Allen Burgess]

Oscillating "Plasma Reed Switch Pulse Motor".

Herr Segelohrenbob demonstrates a "Plasma Arc" between his "Reed switch contacts" in the first 13 seconds of this video posted below. The Reed switch contacts are stationary. Herr Segelohrenbob then runs a pulse motor with his "Reed Switch Oscillator" (Without Transistor) towards the end of his video. A real "Klunker" compared to the advanced concept under discussion; Nevertheless, the increased acceleration is obvious: Does anyone have any idea how high his rotor RPM would climb if his bearing was frictionless with his "Reed Switch Plasma Pulser"?

https://www.youtube.com/watch?v=Q8GkmFRMMAE

[Allen Burgess]

Plasma Reed.

Here's the German experimenter, Herr Segelohrenbob: Woopyjump refers to his "Plasma Reed" videos. The Reed switch contacts are not doing the switching; The "Magnetic Plasma" is doing the switching, not the mechanical contacts:

https://www.youtube.com/watch?v=ZJulY-COfPo&list=PLWdWBXGOdcpQSBeNDZjZJWxEFgdMve3ss&index=3

[Allen Burgess]

Plasma in a Reed switch.

Woopyjump video:

"So it seems that in a vacuum (the reed switch ) that is is possible to get a very nice plasma (and of course the reed is not switching at all)!

I believe that switching the Reed switch in the microsecond range with a frictionless rotor and oscillating switch does not involve the Reed switch contact switching at all, but a "Magnetic Plasma Reaction" like the one we see in this video by Woopyjump:

Regards Allen,

https://www.youtube.com/watch?v=58SzOsmyBgc

[Allen Burgess]

9mH power coils.

"Steel core Inductor 9mH 14 AWG Audio Coil crossover subwoofer 500W 0.31 DCR PAIR".

These are the (Off the shelf) factory wound coils Ossie uses, around $39. a pair off ebay: Four of these coils drew about 600 milliamps with the "Oscillating Reed switch".

solinear:

"The problem that you'll run into with the iron core (the neo mag grabbing it) will be more problem than it's worth to increase the efficiency of the EM by that small amount. This is why electric motors rarely use ferrous cores - they're more trouble than they're worth".

[Allen Burgess]

Ossie's REAC. (Radiant Energy Accumulator-Converter).

A Working Radiant Free Energy System Part*2 - By Ossie Callanan
*
Before I get into the radiant energy accumulator-converter, I just want to highlight how important it is to build and play with the circuit I described above. Only after adjusting and watching the input current and how the charging battery charges can you truly see how these radiant energy pulses are affecting the charging battery. In terms of why it works or how it provides so much radiant energy you have to understand that if the reed switch stays closed, which will happen when they get*worn and sticky, with the 9mH (bought off the shelf) crossover choke solenoid coil I use, the transistor is turned fully on and at virtually it's lowest resistance and so the current draw is about 6-8 AMPS for a single coil circuit!!! It seems this is a key requirement for generating these radiant energy pulses with a transistor. You have to switch the transistor fully on at maximum current for the coil and input voltage. This is another thing the SSG does not do well. But yet, in this circuit, when the reed switch is adjusted correctly, you can get the input down to just a few milliamps if you want!
*
OK, now to the radiant accumulator-converter. The requirement for this appears to be because the charging battery is not very efficient at absorbing all of the radiant energy pulses. John had related this as being due to impedance matching but I am not sure of this at this stage but impedance*may be*a factor. Because the charging battery does not absorb much of the radiant energy by itself, you MUST have an accumulator-converter to absorb and convert the radiant energy for the charging battery to use. Ok, that said, what is a radiant energy accumulator-converter?
*
A Radiant Energy Accumulator-Converter (REAC) is nothing more than a dipole! But the larger the dipole the better! The dipole can be a battery but that is silly when we are already charging a battery. Well in that case, it is a special battery. It is a battery that is mostly composed of potential but little current. The higher the potential the better the accumulation/conversion but some current is still required to be able to pass the energy back and charge the charging battery.
*
There are a number of traditional dipole's that fit what is needed. There is a simple long and raised wire antenna and ground, but this will not provide enough back current to charge our battery. There is an earth battery setup, but unless you want to put in the effort and amount of materials to raise the voltage and still have some required current this requires a lot of work and materials. Finally, I found the best compromise to be "old, dead, sulphated lead acid batteries". At this stage of my research the condition of the battery does not really matter as long as it is dead and sulphated. As long as they are old and dead such that they can barely light up a 12V 100ma light bulb, they will do just fine. Gee I am glad I never threw away my old dead batteries that*kept*piling up.
*
Go down to a battery recycler or junk yard and you can buy pallet loads of old and dead UPS batteries for only a few dollars. When I say pallet load, I mean pallet load. The bigger the bank of these you get the batter. Connect them both in series and parallel such that if they where good, you would get anywhere from 48-120 volts. When connecting in parallel make sure that each*12 volt segment has an approximately even capacity in A/Hs. You can put this bank under your house or table or even bury them in the ground. It is no problem as you will never have to do anything to them again (as long as they are sealed)... They will NOT keep running down. They are already run down; all you need them for is to*use their potential*and their dipole and their hidden capacity. The very small amount of current they will provide for the size of the bank due to the crystalline resistance of the sulfation is all that is needed to provide the free energy that the will convert the radiant energy pulses and feed it back into your good charging battery. I believe that these sulphate crystals may indeed be the main component that is doing the radiant energy conversion for us. Now for how to connect up your REAC. See the following diagram: (See below)
*
You must connect the REAC directly to the charging battery as I have shown above. Amazingly, there is a great voltage different when you measure the voltage directly across the charging battery compared to the voltage measured across the REAC whilst the reed motor is running. This is even with thick cables connecting them but distance does affect it as well. You must have two separate sets of cables. One set going directly from the radiant energy charger to the charging battery and the other set from the charging battery to the REAC.
*
I have run the above setup for over one month now. Following is a picture of my dead batteries that I use as an REAC. (See below)

Using my good 33 A/H UPS batteries, I can charge them up from 10 volts to 14 volts in*about 6 hours with the radiant energy reed motor running 4 coils drawing only 600ma. I can then swap the source battery with the charging battery and keep doing this until I have both batteries charged in about 24 hours. I have done this very many times and it appears to be improving over time.
*
But one thing I want to make clear if you*think that I am somehow just using the stored energy in the REAC bank. If I do not use my reed motor, then the charging battery will not charge. If I try*replacing*the reed motor*with a regular battery charger, the battery will take as long to charge as a normal battery charger would to charge it. When using the reed motor, the REAC is converting most of the radiant energy and providing the energy back to the charging battery. There you have it, a fully working radiant free energy system. Enjoy!
*
Regards,
*
Ossie Callanan
*

[Allen Burgess]

Multiple pulses.

Quote from Ossie:

"Switching a coil on very rapidly using a transistor will produce one radiant energy pulse from the coil’s Back-EMF, but one pulse on its own is no good. You need thousands or better still, millions of those pulses for them to be of any practical use".

Maximizing "Radient Output" is a function of the number of pulses. This leaves us with two variables: Pulses per magnet pass and RPM. The "Oscillating Reed Switch" increases the number of pulses per magnet pass; The rotor speed the number of magnet passes per second. The frictionless rotor should multiply Ossie's COP>10 by many times!

Quote from Ossie:

"My prototype motor uses four of these circuit's, positioned 90 degrees apart around the rotor, and all connected in parallel. You can use just one reed switch to switch all four transistors and coils but it is more load and the reed switch does not hold up for very long".

Four power coils and one Reed switch which sticks?

How about four power coils and two oscillating SPDT Reed switchs for a twin reciprocator?.

[Allen Burgess]

Bismuth rotor.

Attaching the diametric arc segment magnets to a tube positioned between the circular Hallbach arrays would add their magnetic repulsion to the bismuth axle along with the circular Hallbach arrays. This tube could extend beyond the ends of the Hallbach arrays and have sintered radial polarized ring magnets attached whose magnetic strength would help repel the bismuth axle also and act as levitator magnets for the over head coils; So we wind up with six major internal fields, and four major external fields. The diametric arcs for powering in the center, and the radial polarized monopolar fields for precision levitator positioning on the ends; All focusing their combined fields inward to the repelling bismuth axle along with the unidirectional Hallbach rings. The central tube can run through the inside of the Hallback array frames and and the radial end rings and be perfectly balanced, with the diametric arc segments glued to the center. We'd see four rings and the two arc magnets in the center, and two electromagnetic coils suspended close overhead at the ends. This entire rotor and axle can sit safely inside a clear plexi-glass enclosure, sealed for air evacuation. The oscillating power coils can run from outside the protective safety housing along with the levitator coils, magnetically positioned by biasing magnets.

The abundant "Overunity" output would come from harvesting the "Radient Spike" like Ossie Callanan demonstrated and would be entirely "Lenz Free".

[Allen Burgess]

Arc segment magnets.

A couple of opposing radial polarized arc segment magnets glued to the outer perimeter of a stack of Hallback arrays, might be all that's needed for a levitating, frictionless, bismuth axle diametric rotor:

[Allen Burgess]

Halbach array

This plastic circular Hallbach magnet array holder is for sale either as a 3D file or molded for $10. and $14:

This array of 10 mm magnet cubes should spin around a thick bismuth axle with no problem! The diameter of the array holder is 58.68 mm's, so the diameter of the bismuth axle would need to be around 1 1/2". Successfully spinning this array as a levitating ring around a bismuth rod would constitute a major breakthrough in "Spin Technology"!

EdgarInventor

+zebok3 Yes, both on Laser-cut acrylic: Make your own toys - Halbach 12 Magnet Laser cut, as a stream for your 3D printer, https://www.myminifactory.com/object...net-array-6518, or already 3D printed on Sculpteo: 'Frame for the Halbach 12 Magnet Array' | 3D Printing | Sculpteo

[Allen Burgess]

http://www.free-energy-info.co.uk/Chapt6.html