Oscillating Reed Switch Pulse Motor.

[Wistiti]

@Wistiti,

Wow! Really looks awesome. Thanks for showing it. You added some impressive heavy copper, 18 AWG. Does it work? How many volts are you using? I bet that coil would spin a neo sphere.

It would be a simple matter to calculate the resonant frequency if you can read the farads off the capacitor, along with the Ohms of the coil.

Hi Allen!
I use 2xaa battery as the source. My cap is a 160uf photo flash capacitor. The resistance of the coil is 0,8ohm.
I use a gap betwin the magnet and the steel core to start it and adjust the frequency...

[Allen Burgess]

Reed switch oscillator.

@Wistiti,

Wow! Really looks awesome. Thanks for showing it. You added some impressive heavy copper, 18 AWG. Does it work? How many volts are you using? I bet that coil would spin a neo sphere.

It would be a simple matter to calculate the resonant frequency if you can read the farads off the capacitor, along with the Ohms of the coil.

[Wistiti]

Here is my last setup... ��

[Wistiti]

@ Wistiti,

Can you upload another photo? It would also be interesting to see if the oscillation can power a spinning neo-sphere magnet.

Sure! I will take one when i 'll be back home....

[Allen Burgess]

By the way laminate steel work great for the coil core... No freqeucy trouble for me. ��

@ Wistiti,

Can you upload another photo? It would also be interesting to see if the oscillation can power a spinning neo-sphere magnet.

[Wistiti]

By the way laminate steel work great for the coil core... No freqeucy trouble for me. 😀

[Wistiti]

Have you ever scale it up??

[Allen Burgess]

Diodes and flyback.

Look at, and contrast the different ways the diodes are facing in these two schematics below; The George Cianiotakis schematic on the left has the LED cathode connected to the negative pole, whereas the Simplefix 2969 schematic on the right has the diode and LED'S reverse biased: The Simplefix 2969 LED'S are illuminated by the higher voltage flyback, wherein the voltage is reversed and the current direction unchanged from the breaking of the switch contacts. The LED on the Cianiotakis oscillator is illuminated directly by the generated current. That's why the LED cathodes are connected to opposite power poles in the different schematics. The LED'S and diode in the Simplefix 2969 schematic collect flyback, help protect the Reed switch from detrimental arcing, and prolong the longevity of the Reed switch contacts to a great degree. The Cianiotakis Reed switch will burn out way too soon in his oscillator from the fluctuating plasma arcing, rapidly and corrosively eating away at the metal contact points. Two powerful north, south, quenching neo magnets on either side of the Reed switch would help to very effectively prolong the lifespan of George Cianiotakis's oscillating Reed switch contacts; Seen on the left below:

[quantumfanatic]

@Allen

Thanks,I understand what is going on now,will try to replicate

Qua

[Allen Burgess]

@quantufanatic,

Those red diode symbols with the two dashes over head are "Light Emmiting Diodes" or LED'S. I think the standard 3 to 4 volt model would work.

"Standard20 mA LEDs (ranging from approximately 40 mW to 90 mW) at around: 1.9 to 2.1 V for red, orange, yellow, and traditional green

3.0 to 3.4 V for pure green and blue

2.9 to 4.2 V for violet, pink, purple and white

Ultra-high-output20 mA at approximately 2 or 4–5 V, designed for viewing in direct sunlight
5 V and 12 V LEDs are ordinary miniature LEDs that incorporate a suitable series resistor for direct connection to a 5 V or 12 V supply".

You can see the size of the LED'S in Simplefix's video.

[quantumfanatic]

Thanks Allen
that helps a lot as the drawing's top and bottom is not clear,however,could you give me the values of the three diodes behind the shotky which is col loured in red?
Thanks in advance

Qua

[Allen Burgess]

Shotky diode.

@quantumfanatic,

Try the 1N5819 Shotkey diode.

@Wistiti,

Thanks for the snapshot!

[quantumfanatic]

Thanks wistiti

I have the same drawing,what i want to see is what is behind the shotky...I can't see it..
I need the values of the diodes..please help

Thanks in advance

Qua

[Wistiti]

Sorry Allen,
That is the design of simplefix 2969 I'm talking about

Hi Quantum.
Here is the one i use. Happy building!

[quantumfanatic]

Sorry Allen,
That is the design of simplefix 2969 I'm talking about