Use for the Tesla Switch

[Bit's-n-Bytes]

@vtech,

can you please post the latest schematic you used in replicating bit's inverter_cap pulser? the one you posted above. coz the links on previous pages no longer work. thanks.


Shingot

Here is the link;

http://www.energeticforum.com/attachments/renewable-energy/7854d1299600803-use-tesla-switch-ts_voltaic_amp_v2-3b_inverter.jpg

Thanks

[shingot]

@vtech,

can you please post the latest schematic you used in replicating bit's inverter_cap pulser? the one you posted above. coz the links on previous pages no longer work. thanks.


Shingot

[blackchisel97]

Hi Vtech,

Great video, thanks for posting

Looks like you have it running beautifully. What was your draw current into the inverter section?


John K.

Thanks John, When I had first run with pause value at 40 it was pulling around 350mA. Later, when I increased freq. (reduced pause to 5) it was drawing almost 2A but charging was amazing. Since I didn't have heatsink installed properly I increased pause to 10 and current stays around 0.7 - 0.85 depending on battery condition. That was the setting used in video.
I think I finally figured out how to get this done "analog way" with mosfets, like in John Bedini patent but since I have this running so nice...I guess I'm too lazy However, I'm in "building mood". Finally have time to do it


Vtech

[sujan_ms]

hey jeff .... i have a doubt i have come across this 330uf ,450V capacitor and can i use it instead of 33000uf,35V.....and if i use an SMPS as a source
can i omit the 33000uf,50V capacitor . i.e a DC input .

Thanks for the reply jeff, as you said i can elminate both but here in india i wont get 470uf ,50 V so can i go ahead with 330uf,450V , i think it should not be a problem at all....and as for the 35000uf, 50 V i will be applying a DC voltage so i can eliminate that too right.

[John_K]

As I promised - short youtube about my replication of TS_Inverter Voltaic Amplifier YouTube - TS_Inverter Voltaic Amplifier


Vtech

Hi Vtech,

Great video, thanks for posting

Looks like you have it running beautifully. What was your draw current into the inverter section?


John K.

[blackchisel97]

video update

As I promised - short youtube about my replication of TS_Inverter Voltaic Amplifier YouTube - TS_Inverter Voltaic Amplifier


Vtech

[Bit's-n-Bytes]

hey jeff .... i have a doubt i have come across this 330uf ,450V capacitor and can i use it instead of 33000uf,35V.....and if i use an SMPS as a source
can i omit the 33000uf,50V capacitor . i.e a DC input .

You can actually eliminate both. If you want small gains in potential across the FWBR, you could use a 470uf or 680uf @ 50V without any further stress on the Transformer.

@Vtech, thanks. Glad to see this is working well for you.

Bit's

[sujan_ms]

what value should i set the R9 i.e 10K pot so that i get accurate pulses....??

hey jeff .... i have a doubt i have come across this 330uf ,450V capacitor and can i use it instead of 33000uf,35V.....and if i use an SMPS as a source
can i omit the 33000uf,50V capacitor . i.e a DC input .

[blackchisel97]

Inverter Voltaic Amplifier

Hi guys, After couple busy nights I finally managed to replicate Bit's IVA according to last revision . I had a little problem with too small transformer getting warm but just found bigger one and swapped few hours ago. I have 10 000uF caps which I'll replace with bigger values as soon as they arrive. Anyways, this is real beauty, works really nice. I'll make a short tube when I get some rest. Been working all night. Big to Bit's, NVisser and everyone for contributing and making this progress possible.
[IMG][/IMG]


Vtech

[alexandre]

Thanks Bits!
Best
Alex

[Bit's-n-Bytes]

Bits, I was once again thinking about the tesla switch, and wondering, were you able to get a real, usable charge?

I would like to replicate the effect and show it at the university. And give all the credit that is due (Brandt, Bedini, Mueller, Bits, the forum, and that civil engineer guy who pantented it ages ago).

Best,
Alex

Thanks Alex, yes there are very exciting developments happing with this TS even as I am writing this, but I must wait till after the July conference. John K. and myself will be presenting the TS and it's multi-functionality.

Bit's

[alexandre]

Thanks Alex, yes in the original TS matching the load was critical but at the end of the day, that batts didn't gain. In the New TS, the load and charging are seperated.

Hope this helps

Bits, I was once again thinking about the tesla switch, and wondering, were you able to get a real, usable charge?

I would like to replicate the effect and show it at the university. And give all the credit that is due (Brandt, Bedini, Mueller, Bits, the forum, and that civil engineer guy who pantented it ages ago).

Best,
Alex

[John_K]

Hi All,

Just posted my first YouTube video of my first attempt to replicate the tesla switch. Apologies for the poor video quality and the shaking at the start but I didnt have a tripod and was trying to juggle the camera.

Here it is:

YouTube - Tesla Switch Replication 1

Let me know what you think.

Any help with the replication effort would be greatly appreciated.

Regards,

AusEv

Hi AusEV,

Welcome aboard! Great to see another Aussie having a go at this.


John K.
(Melbourne)

[ausev]

First video

Hi All,

Just posted my first YouTube video of my first attempt to replicate the tesla switch. Apologies for the poor video quality and the shaking at the start but I didnt have a tripod and was trying to juggle the camera.

Here it is:

YouTube - Tesla Switch Replication 1

Let me know what you think.

Any help with the replication effort would be greatly appreciated.

Regards,

AusEv

[Bit's-n-Bytes]

what value should i set the R9 i.e 10K pot so that i get accurate pulses....??

You should set that to have 2.5V going to the chip at optimum cap voltage of 44V. I think all of these were discuss in ealier post within this thread.

Thanks.