gravity waves found

[david lambright]

hi...

jet, did your mail come yet?...when you get the device, it is charged and working...please show as many people as would be interested in this type of thing!.....harvey, do you get any "compression" in your viewfinder?...at mikes house#3, what i saw on the viewfinder was the same as the video...shutter artifacting?...your replication is fantastic! you are doing everything i was doing....testing it every which way, your compass readings are similar, your device must be radiating....how many people have seen this replication?.....with the device spinning, have you held a piece of quartz near it....this usually helps it to be viewed easier....show this to others and see if anyone sees this effect....it is there, just very, very subtle.....your device is obviously charged exactly as mine...the effect must be present?...david

[woopy]

Hi all

next experiments and results

1- the pmh in epoxy resine. No assymetry at all. The resine polymerises completely flat,pix 1

2- i put a neomagnet at both ends of the U bar but i did not energised the pmh
pix 3 shows the icing . There are deformation in the center, but few assymetry. And almost no tunnel effect. And the neo mag are much stronger than the energised pmh.

3- i redo the previous test exactly same config (same matos at the same freezer and same orientation) but without the magnets and pmh energised.
pix 4 shows the strong assymetry in the icing. And the nice circular tunnel effect.

4- my daughter who is osteopathe and kynesiologue. put her hands arround the pmh, and she could feel the strong and assymetrical ernergy . Than she tested the pmh with neomagnet and not energised and no feeling .She than tested with a pendulum and it is amazing to feel that the pendulum try to avoid the proximity of the pmh. Than i showed her the pix 4 and she immediately said " it makes me think to a yin and yang design"

OK,as i am not at all specialist of those kind of energy, i don't know what is going on here but surely something interesting.

For info i tried to test the pmh by placing coils all arround and check with the scope, but no measurable results. Any idea how to test with the scope ?

good luck at all

Laurent

[gravityblock]

Here's a video of my replication of the Baker's Device, YouTube - Baker's device

I used the nylon fibers found inside a CAT 5 cable. All I need to do now is to add a mirror to the nylon string to reflect the laser light, then seal it up so there are no air currents to affect the experiments. I also need 4 ring magnets so the combined forces of the earth's magnetic field and those of the doughnut magnets almost cancel each other out so it will rotate quite freely and be the most sensitive. This setup detected a magnet from 4 feet away without the nulling magnets in place. It didn't take very long to assemble this apparatus and it was easy to build.

GB

[Harvey]

Various Vids

Hi Guys - I have a few more vids up.

YouTube - Lambright - 003

YouTube - Lambright - 004

YouTube - Lambright - 005

The last link is a play list of various colormodes - most of the vids in that list are between about 40 seconds and 2 minutes long but I did spend about 7 minutes on the first Sketch Mode vid. Originally I had intended to stitch all seven into a single vid but the playlist made that unnecessary.

Let me know if you guys spot anything that you would like me to focus on.

I am going to try and borrow my sons HD camera and see if there is any contractions or elongations present in a motion lock mode. Also, I still have my cardboard mock-up that I can do some comparisons with.

Cheers

[Harvey]

harvey,

nice work, looks really neat.

can you take a digital still from above while its spinning to see if you also get the elongation & contraction in the image...and then..take a still of a rotating piece of card with some curves drawn on..to see if you get the same....this will prove once and for all what is going on.

I'll see what I can do - but my other test with the mock-up did not show the contraction and expansion. I have a few different digital cameras I can try (phones and such).

I have another HDPE disc I will try also without the magnets inside also.

Thanx

[IndianaBoys]

Hi Indiana

thank's for input

but what do you mean by the freezing wind.

just for info i have 2 freezers and they are situated one regarding the other (opposite to each other) and the result are about the same if i freeze an experiment on one and than do the same on the other one. (so long i respect the earth orientation of course)

But effectively i would be very interested if you can explain some more to avoid basic error

Thank's

Laurent

Woopy,

Just wanted to rule out the freezer fan blowing on your experiment and affecting your freezing patterns of water.

IndianaBoys

[Harvey]

Hi Harvey,
Did you sand the surfaces where the pipes make physical contact? That's assuming it was necessary with your material. I recall David did this with his.
-Steve
rimstar.org - Solar/wind, composting, non-conventional energy/propulsion Wave Structure of Matter (WSM)

The pipe was relatively clean, but yes, I did clean the oxide off a bit anyway.

[broli]

Very cool experiment woopy. Just for fun could you add more salt or sugar to the water and see if there's a difference.

[woopy]

Hi all

some more pix of this afternoon test

i do not see any influence of air movement in my different freezer

and any
way my question is the same

what is this ring of air all arround the basis of the pmh

the 3 pix shows the evolution during the freezing process.

1 after 1 hour all is frozen apart one specific part (dark zone)

2 after 2 hours all is frozen and the dark zone is now elevated , (higher than the rest of the surface)

3 and you can see in pix 3 the circular tunel of air surrounding almost all the contour (see the red arrows)

please consider this as an important question as to solve the leedskalnin beautifull energy solution

thank's

good night at all

Laurent

[woopy]

Hi Indiana

thank's for input

but what do you mean by the freezing wind.

just for info i have 2 freezers and they are situated one regarding the other (opposite to each other) and the result are about the same if i freeze an experiment on one and than do the same on the other one. (so long i respect the earth orientation of course)

But effectively i would be very interested if you can explain some more to avoid basic error

Thank's

Laurent

[IndianaBoys]

Woopy,

Good work!

Not sure if you shield the container while it is freezing?

If not, suggest you wrap it with saran/plastic wrap to keep the wind off the water as it goes to freeze.

IndianaBoys

[woopy]

Hi Jetijs

fantastic catalogue of fotos thank's

At all

For myself i go on to test with pmh in ice and to try to understand what is going on here.

I have made some different config of pmh. The last and small one are made with a shakles from which i remove the axel, They are cheap and work very well.
I make only one coil of 100 turns 0.3 mm copper wire(wound in 2 minutes) and it works very well. from 4.5 to 24 volts.

I tried different basis config from bar to tubes to ring to washers etc.. everything works fine.
pix 2 and 3 show a config with a basis square and the result once iced. Very strong assymetry

The assymetry is different depending of the orientation of the pmh poles and the earth magnetic orientation. Seems to have a major importance.
For instance all my last test are made with the N pole of the pmh regarding to west. (that is to say that i have checked that the freezer do not disturb the earth orientation.

If i put enough water in the container, i often remarked that a kind of ring appears in the ice, often in oval around the basis.
In pix 4 and 5 , (same config as previous pix ) the red arrow show a part of this oval ring, and if i crack the ice i can see a real tunnel in the ice . Very weird. Can somebody explain it ?

Last pix is a mini pmh on a washer basis , and a nice assymetry in the icing.

Yep this pmh is very impressive

Hope this helps

good luck at all

Laurent

[rave154]

harvey,

nice work, looks really neat.

can you take a digital still from above while its spinning to see if you also get the elongation & contraction in the image...and then..take a still of a rotating piece of card with some curves drawn on..to see if you get the same....this will prove once and for all what is going on.

[stevend]

Hi Harvey,
Did you sand the surfaces where the pipes make physical contact? That's assuming it was necessary with your material. I recall David did this with his.
-Steve
http://rimstar.org http://wsminfo.org

[Harvey]

Just a quick note to say that I uploaded MP4 vids instead of the 3G2's and now the audio works. I don't know why You-tube stopped supporting the 3G2's but there 'ya go

@David,

I may want one of those oxide rings after all - I dug some more and I don't have the aluminum tubing nor can I find the Developer (which is some type of ferrous compound that I cannot recall now) but I guess it got used or tossed.

Cheers,