gravity waves found

[david lambright]

hi

the segments fit a little better at 19mm , video soon...david

[david lambright]

jet!

David,
I have cut the pipe you sent me in 12 pieces, each 2" long. And all those pieces are cut in half.



Tomorrow I will see what HDPE boards I have at my disposal and continue the work. I will go slowly and do everything according to your videos to get everything as close as possible to your setup.
Thanks!
Jetijs

great work!....here is the link to #4 http://www.youtube.com/watch?v=u8rGKHKolhY.....david

[thekubiaks]

JET.........go easy with the laser cutting thing.........this might be one of those things......where.........elbow grease pays dividends.......the laser "might".......affect things in a way we cant fathom as yet

I respectfully disagree. I am thinking that the lack of anyone to reproduce the findings MAY have to do with a localized Earth magnetic "anomaly". What is a common denominator between Coral Castle, the Egyptian Pyramids, and Salem, Oregon?? Something?, Nothing? We need someone to go to Salem and report their findings.

[rave154]

JET.........go easy with the laser cutting thing.........this might be one of those things......where.........elbow grease pays dividends.......the laser "might".......affect things in a way we cant fathom as yet

[Jetijs]

Thanks Rave
It also turned out that the laser unit is now repaired and I will have my laser cut Leedskalnin wheel any time soon. I noticed, that Davids pipe material is much softer than anything I used before, this might or might not be important

[rave154]

damn JET.........your attention to detail is more than admirable

as we say over here........ you're a good'en

[Jetijs]

David,
I have cut the pipe you sent me in 12 pieces, each 2" long. And all those pieces are cut in half.



Tomorrow I will see what HDPE boards I have at my disposal and continue the work. I will go slowly and do everything according to your videos to get everything as close as possible to your setup.
Thanks!
Jetijs

[david lambright]

hi kubi

and now we return to the "Gravity Waves found" discussion and the Saturday videos....

i am starting the build videos and should be done tomorrow ...i will be free after that ...or if you are in the neighborhood, stop by...and saturday market was educational...i need a cameraperson to capture the moment they see the wave...i will try next week.....thru october!......david

[david lambright]

#2...

hi everyone, i will be posting the video and link in a moment.Yes about the zinc,smooth the bumps down to get good contact, for the most part leave the zinc on. I will be going step by step through all of it.I will try to answer all questions.I know there are easier way's to cut the pipe, but I will show you how I cut it. More soon!.....dave...here is the link....http://www.youtube.com/watch?v=Jjh5OE6yerk...thanks...part 2;YouTube - step by step #2..........part 3;YouTube - step by step #3

[Harvey]

Thank you for your kind words

I've been learning new things here, so this is fresh for me. I would like to hear more about the magnetic Aluminum and its specific interactions. I was thinking how could it be magnetized and yet not effect the compass reading. One way would be if there were U shaped flux channels in the material like so:

<<< Needle ^ Here<<<
------------------------
===================
===================
nnnnnnnnnnnnnnnnnnnnn


So the upper part is normal Aluminimum, but the bottom layer has those U-turn paths that can be like Ferromagnetic material and even hold a magnetic charge.

[Harvey]

David, the pipe has arrived. I can start building. If you have something to add or suggest, please do.
I will document everything.
Thanks,
Jetijs

Let's hear it for international delivery success

galvanized pipe is usually a bit bumpy - but David did say "leave the Zinc on" - so... I guess it means just smooth off the bumps where they connect right?

BTW - I was looking at Ed's rig and noticed there are 4 coils permanently wired at each indent of the cloverleaf ring. Also, in his writing he mentions using a coil to enhance the magnetism of the 'generator'.

Also - I did not know that he moved everything to a new location after he was almost finished at the old place. I've been learning a lot the last couple of days

[Jetijs]

David, the pipe has arrived. I can start building. If you have something to add or suggest, please do.
I will document everything.
Thanks,
Jetijs

[david lambright]

@ David



What is the procedure to knowing that the wheel is locked? What does the compass do that is different when the wheel is locked? What should I be looking for?

I was of the opinion that each side of each part would show a different pole but that is now what I got. Instead, I got four poles, two norths and two souths. I assumed the wheel was locked having gotten that far. Thinking that two norths and two souths was a locked wheel isn't so very far fetched since a washer shaped magnet has just that as does the cylinder magnet in the fan motors I've hacked. Now I'm finding other motors with even more poles in them.

Warren
..

i have had so many different configs of pmh... with a toroid and single junction, i had as many as 6 poles....the config now seems to have 4.....when i say lock, i am not saying a strong lock...just strong enough to get the "flux"path to lock and start an orbit of force inside the metal.....the compass when placed in the center and then energizing, usually the needle will spin first, then stop at a different point than the beginning...i had the rotor on upside down at first but after i switched it i did re energize it..your setup seemed to be doing all the same things as mine, great work... ...the effects i listed are subtle...but they are there! ...sorry about not getting back to every one, please forgive me..saturday market......why do people not like to be filmed....plenty of people saw the wave ....nobody wanted their picture taken...maybe it does steal their spirit!?....any way i hope this helps ...also it seems that to get the best visible effect, after its working again, hold a weight of steel or iron over center axis, around 10 degrees off towards north and spin it ...you should feel a spot where it pulls down the most.....thanks...david

[mrbreau]

Fwiw2

FWIW

I believe, and have already stated so, that David just might have developed a magnetic gate.

Link1; YouTube - Discovering Magnetism Magnetic Gates Howard Johnson 2006 part 1

Link2; Bedini's Magnetic Gate

[mrbreau]