Imhotep's Radiant Oscillator Video

[Aromaz]

YouTube - levitation melting with induction heating

Hmmm, nice. We are using such machine in our factory for three years already - heating up stainless steel for bending; takes only few seconds. Keep it too long and it melts all away. Hot energy with plenty of amps = hot energy with plenty of amps.

The challenge I have: Make things levitate without magnetic force and without melting them.

[nat1971a]

and the system was on....but no lights.......no where else in the entire garage except where my system was.....is that a coincidence?

[nat1971a]

looks like i am out of business for now....looks like water has gone over my entire system...what are the odds of that happening......just soon after i was getting WHITE sparks from my spark gap...

[nat1971a]

the system wasnt running....dont know where the water came but it has been raining here quite heavy but that stopped some time ago...mind you it was strange that it is only around my system....assuming it is water......i will let the burning smell go away first before i go in there......unless one of the batteries has ruptured...dont know yet.....am in no hurry to go in the garage at the moment

[broli]

man dont ask me what just happened....i was thinkering with my system...and the spark gap with the cylinders...and i think the trannie popped.....so i went inside to have a break.....a go back 15 minutes later....smell of burning rubber.....ignition coil is bubbling.....water on the floor......i think i will have a break for a while......

Are you saying you left it on? And where did the water come from?

[nat1971a]

man dont ask me what just happened....i was thinkering with my system...and the spark gap with the cylinders...and i think the trannie popped.....so i went inside to have a break.....a go back 15 minutes later....smell of burning rubber.....ignition coil is bubbling.....water on the floor......i think i will have a break for a while......

[nat1971a]

another cylinder in the hutinson movie!!!

[mlurye]

I would suggest to watch this move about zero point energy.http://www.hutchisoneffect.ca/Videos...oZeroPoint.wmv

[Inquorate]

Mug shots

That sounds like a dare. You're on... Ps bodkins, seems like you're scouring the net for anything on lightning.. By jove, that's top stuff old boy! keep up the good work, eh wot.

[Bodkins]

http://www.springerlink.com/content/w2n710r236016022/fulltext.pdf?page=1

whistlers Eckersley

Inquorate@ come on lets have a photo!!!!!
We all should do a shades mug shot

[Inquorate]

Wearing glasses

The missus makes me wear protective glasses, which she makes worse by laughing whenever I put them on as ordered. Sigh.

[broli]

Also something that has been mentioned quite some times here.

You can replace a component but you can't replace your eyes. So please wear protective Polycarbonate eye glasses for the many corona discharges you see that also emit UV rays.

It's really a small investment for something very valuable....

UV-Protective-Polycabonate-Shooting-Glasses-CLEAR

[Bodkins]

YouTube - levitation melting with induction heating

[Inquorate]

Putting one ignition coil to another

I've done it, check the case of 2nd coil with a neon, lights up... ???

[mlurye]

Add more CFL's ? 1 to 3 is not enough. I found 'Amp' drop after 3 CFL's.
How bright are your lights when compare to normal mains AC?

I found onother way to drop current draw. Yes you do need 3 or more CFLs. But I did put few ignition coils around driving one. And connected only HV output on them between each other. Then HV out of driving coil on one end of CFLs and HV outs of coils around on other brightness didn't drop (put spark gap here to increase brightness) but current did drop twice.