Free Energy At Last Step By Step Must See

[**~Imhotep~**]

never give up

I noticed that alot of people when they first start building these fans ran into the same problem that i did at first. The casings on some of these fans are a little flimsy and even if your super careful they can easily be broken. That does not mean that the fan is useless. I am posting some pics of one of the fans that i had to take a little imagination with after i broke the outside casing.

You will take notice of the "tesla pancake coil" i made out of this house wire that holds the unit up. It walks a little bit but it still gives good data.

A old 2 liter bottle cut into a ring makes a good "protective shroud" to make sure no one can accidentally get hurt when its running.





it just shows that even with no shroud these little motors can still pack a punch

[**~Imhotep~**]

Hi All
Im new here been reading and building the fan sg Thanks Imhotep (cant beleive your a rush fan thats so cool)
Its really make life alot easy had no-end of trouble with the north pole motor still useing a reedswitch to get it going.
Anyway I have a question or two.
Do i just put a cap in line before the battery to Charge or can i just go into the battery?
also would love to pulse charge the batterly with a 555 but im not big on eletroics can someone help me out?

Free energy for All + Freedom=Result

you can hookup caps directly (it charges them fast be careful) i used large 680 microfarad 250 volt, three fans in parallel output,or one doesn't matter.

you can also hookup batteries directly of any voltage size, i have mixed different voltage batteries with no problem , monitor volts and be careful.

as far as pulse charge have not tried ,but have been working on different pulse charger (very interesting arrangement will disclose shortly ,runs 110 or higher resistive loads directly ,all mech. no chips or transistor,not complete on secondary side of tube yet.

others in forum have 555 pulse project complete with computer fan i did not see schematic details should be further back in thread tho. happy experimenting

[Bodkins]

Hello All

Hi All
Im new here been reading and building the fan sg Thanks Imhotep (cant beleive your a rush fan thats so cool)
Its really make life alot easy had no-end of trouble with the north pole motor still useing a reedswitch to get it going.
Anyway I have a question or two.
Do i just put a cap in line before the battery to Charge or can i just go into the battery?
also would love to pulse charge the batterly with a 555 but im not big on eletroics can someone help me out?

Free energy for All + Freedom=Result

[**~Imhotep~**]

i ran into one with brass sleeve instead of clips ,it also had spring between rotor and stator . it has become my tesla pancake one that i described earlier i took hemostats and twisted the sleeve until it came off .hope that helps

[**~Imhotep~**]

your readings are correct, thank you happy experimenting ,i will be posting any new data as i confirm them , thank you

[theremart]

RE: size of spike

looks like you have it set to channel b. Is that correct, and the division is on 1 volt per division dc, and the sweep is set to 1 or 2 millisecond. Its hard for me to tell from the angle but it might be my eyes..lol.


Looks like EXCELLENt spikes. YAY!!!

now everyone can hook the scopes up to the fans and see them. Is it the fan that you altered with super high rpm.

What is the total spike voltage? Its kinda hard for me to tell but it looks large!

Well for 12V I am getting 60V spikes if I am reading this correctly The scale is 1 V I have the probe at 10X and it takes 6 segments on the screen. I am brand new with this scope stuff, ....

[**~Imhotep~**]

Keep up the good works. The world needs inventors to provide solutions to energy problems!
Carry On...

thank u for the kind words. Happy experiementing

[**~Imhotep~**]

Hi everyone...

~Imhotep~, have you run into any ball bearing fans? The box o' fans that I got are all top-of-the-line ball bearing fans (used in a large parallel computing array)... After taking the clip off of the shaft, the fan still wouldn't budge. It felt like there was a spring in the middle somewhere. It would pull a little bit and then go back in. (It wasn't because of the magnetic attraction) I decided to "sacrifice" one and the shaft ended up breaking off where it was glued to the fan blades! The stator is really nice and the inside shafts are all metal. Any ideas on getting the center shaft with the fan blades to come out?

I'm going to try to press out the center shaft on this broken one to see if it will come loose.

Thanks...

yes i have done ball bearing, and they were really nice ones. I have broken the shafts off on a couple of them and I actually took the shaft after i got it out and stuck it, after i made the hole all the way through the plastic fan/magnet assembly i took the shaft and stuck it back through from the outside glued with plastic glue, didnt put the clips back on and because of the strong magnets it runs fine, and stays in there cause of the magnet attraction..lol.i never give up, is running right now.

[wpage]

Edison & Tesla would be proud!

Keep up the good works. The world needs inventors to provide solutions to energy problems!
Carry On...

[InTheField]

Hi, I had the same problem with the original windings,
for me, this winding works

The ones that I've gotten working are wound that way as well... As I mentioned before, I've seen different winding patterns even in the same fan brand, make, model, same packaging with the same numbers on the boxes...

[InTheField]

Ball bearing fans

Hi everyone...

~Imhotep~, have you run into any ball bearing fans? The box o' fans that I got are all top-of-the-line ball bearing fans (used in a large parallel computing array)... After taking the clip off of the shaft, the fan still wouldn't budge. It felt like there was a spring in the middle somewhere. It would pull a little bit and then go back in. (It wasn't because of the magnetic attraction) I decided to "sacrifice" one and the shaft ended up breaking off where it was glued to the fan blades! The stator is really nice and the inside shafts are all metal. Any ideas on getting the center shaft with the fan blades to come out?

I'm going to try to press out the center shaft on this broken one to see if it will come loose.

Thanks...

[elias]

the ones i rewound ,i used two wires cw ccw cw ccw hope that helps , i no longer rewind they are easy after you do as many as i have .never give up

I appreciate your assistance.

[**~Imhotep~**]

on rewinding

the ones i rewound ,i used two wires cw ccw cw ccw hope that helps , i no longer rewind they are easy after you do as many as i have .never give up

[**~Imhotep~**]

Hi,

I tried disassembling the stator, but no matter how much I tried no luck! I think that I even damaged the windings, so I need to also rewind some of the windings too. Is there any easy way to get it off?

Elias

i have had a few tough ones and used a few methods with success
use low heat(with hair drier) on stator to soften glue, if glue was used.
be carefull not to melt plastic, if its still warm use rag or carefully use pliers to twist,(i cut the power wires going to the circuit board off so when it comes off i did not want to smash or snag the plastic supports with the dangling power wires).

the newegg ones i got were tough and had no posts just wires running through grooves in outer perimeter to the circuit board, successfully got stator off then removed old board and striped the surface mount ics and caps and protection diode off old board ,then put old board on and soldered wires to 4 isolated pads, checked to see that no pads were shorting to other areas and i was good to go(the new egg ones i used pliers on rotor laminations carefully ) it works great.

there are many different types of fans used in computers pwr supp., the easy ones were old ones with posts, that i got for 1 dollar for 6 of them from a computer recycler down the block from me. they had no glue and all had been in use for a long time so they came off easily. hope this help good luck experimenting.

[tbest]

Hi,

I tried disassembling the stator, but no matter how much I tried no luck! I think that I even damaged the windings, so I need to also rewind some of the windings too. Is there any easy way to get it off?

Elias

Hi, I had the same problem with the original windings,
for me, this winding works
________
Mercedes-Benz M275 engine