Multifilar Generator Coil - Lenz delay Experiments

[BroMikey]

Thank You Mr Turion

Here is me being audacious That's me. Squeaky wheel. I
feel like I need to be a public nuisance talking extremes to get
attention.

You will notice that the 11th strand (each one 170ft) was not the null
point but way way past allowing drive motor power reduction of nearly
500ma. Starting at 2400ma dropping to 1930ma without collecting
the coils energy. That energy amount was another 20watts so let look.
Using only half the coils strands. What if I had 6 coils?

88vac x 2400ma = 211 watts drive input dropped to

88vac X 1930ma = 170 watts then add another 20 watts or less.

At 17 strands I generated far less but speed up was great but because
my wire is only rated at 600vac and I was running 1100vac It has
weakened. Untrustworthy for any accurate measurements at this point.

[VIDEO]https://www.youtube.com/watch?v=INXNsyFMBgE[/VIDEO]

[VIDEO]https://www.youtube.com/watch?v=f8kY6IXvjok[/VIDEO]





......................

[SkyWatcher]

Hi mike, thanks for the kind words and positive encouragement.
I see what you're saying, many more can use this, If it can be lenz neutral or better at lower rpm's.
By the way, I guess I did count correctly when I was in the backyard, the coil is 50 strands.
I finished labeling all the strands today, that was tedious.

Also, for those that may not have seen bromikey's coil making guidance in the other thread.

He gave the great idea of putting posts in the ground at 40 feet, and walking the wire around the posts, back and forth, till you have the number of strands you want.

Next step, going to connect strands in series, incrementally.
Then, short circuit them for each series coil pair added, to observe for decrease in lenz effect.
peace love light

Edit: Also just realized, I need to cover all the stripped ends of the strands not in use,
to prevent any of them from touching and messing with the experiment, so, no testing until that is done.

[BroMikey]

Hi all, thought I would make a new thread for this, don't want to clutter up anyones thread.

Experimenting with the multifilar coil, lenz delay effect.
This coil has 51 strands of 30awg. magnet wire.

Used bailing wire, cut to short pieces and spray painted each piece for the core.

The pieces are shoved into a 3/4" diameter length of PVC pipe and super glued in place.
The coil/core former is adjustable.

Also used a new piece of wood for the base, as the previous base was warped and was causing vibrations and noise, it runs much smoother and quiter now.
Using a brushless 400 size, RC airplane motor for the drive, with 2s lithium ion battery pack, hooked to a reciever and transmitter.
Rotor has 8 - 1" diameter by 1/8" thick neo magnets and the rotor diameter is 3-3/4" to outside of magnets.
Will be placing coil strands in series to try and achieve lenz neutral or speed up at reasonably lower rpm's.
Questions or comments welcome.
peace love light

hello Sky

You are really moving along, yes listen to Turion on man, that is what
he is here for. 48 is a great even number and one more thing, all of
these talks we are having right now are repeats of what you have
heard for years.

You are we acquainted with the details. You are very sharp and in my
opinion are one of the few who could actually move this tech forward
at a lower rotor speed. I would have beaten you but right now I am
out of time to do much on coils.

The lower rotor speed of 1200 rpms is still a mystery that I think will
be solved with the shorter strands though I have never heard of anyone
using such short strands and so many of them. Not even Turion. I
don't think so.

What maters is you are trying something new. The reason this test is so
important is that there are thousands out there already using a form
of an Adams or Bedini rotor running as much as 1000 rpm's using those
tape job rotors. They can all get their feet wet with their existing setup.

Here is another reason I like your test. Let's say that with this higher
resistance wire you reach the cancellation null point at the low rotor
speed using 24 strands. Not only would you another 24 strands to make
another output channel but maybe using all 48 strands might let you
run a 500 rpm rotor speed.

Wouldn't that be kool? I think that would be great. This could make for
a switchable multi-speed operation. A motor generator that works
collecting back power at many speeds. Like my room fan, it has 3 speeds.

I did the same thing painting up bailing wire.

[SkyWatcher]

Hi Turion, wow, thanks for all the great information.
Thanks for the coil offer, though I think for now, I'll just experiment with what I have.
It is 50 strands, should have made it 48 though.
I guess I'll just not use 2 of the strands, then I will have a 48 strand coil.
Only half way done marking all the strands with masking tape and checking continuity with meter for matching strands.
That is interesting about the connector strips.
Could it be, when using these multifilar coils at lenz neutral or speed up, maybe it is creating a different kind of energy that is flowing over the connector strip and short circuiting itself somehow.
Will continue working on this coil.
peace love light

[SkyWatcher]

Hi all, thought I would make a new thread for this, don't want to clutter up anyones thread.

Experimenting with the multifilar coil, lenz delay effect.
This coil has 50 strands of 30awg. magnet wire.

Used bailing wire, cut to short pieces and spray painted each piece for the core.

The pieces are shoved into a 3/4" diameter length of PVC pipe and super glued in place.
The coil/core former is adjustable.

Also used a new piece of wood for the base, as the previous base was warped and was causing vibrations and noise, it runs much smoother and quiter now.
Using a brushless 400 size, RC airplane motor for the drive, with 2s lithium ion battery pack, hooked to a reciever and transmitter.
Rotor has 8 - 1" diameter by 1/8" thick neo magnets and the rotor diameter is 3-3/4" to outside of magnets.
Will be placing coil strands in series to try and achieve lenz neutral or speed up at reasonably lower rpm's.
Questions or comments welcome.
peace love light