Oscillating Reed Switch Pulse Motor.

[Allen Burgess]

"Spark Gap Magnet Motor".

There's no video or written material anywhere to demonstrate the functioning of a "Spark Gap Magnet Motor".

Any video of a successful attempt would constitute a historical first!

The spinning diametric magnet will "Consecutively Select" incremental frequencies from the broad band of available "Spark Gap" frequencies, and spontaneously accelerate with constant input. It would help to increase the voltage on the "Tin Can Top Electric Buzzer" from 3 to 12 volts for short run testing.

Attaching a tuned capacitor between the electrode nail and the "Tin Top" in the .5 to 15uf range will generate an efficient A.C. HV spark from a thin wire secondary of many turns wrapped over the primary winding. Identical to a "Ruhmkorff" coil.

[Allen Burgess]

Full spectrum frequency.

Another point is the "Gap Spark" radiation covers practically every frequency as evidenced by the frequencies measured by Chaniotakis from his "Reed Oscillator" 9 to 34Khz:

https://www.youtube.com/watch?v=I24nDi_q-EU

Quote from Wikipedia on "Spark Gap Generator":

"Another problem with the spark transmitter was a result of the shape of the waveform produced by each burst of electromagnetic radiation. These transmitters radiated an extremely "dirty" wide band signal that could greatly interfere with transmissions on nearby frequencies. Receiving sets relatively close to such a transmitter had entire sections of a band masked by this wide band noise".

The "Gap Spark" is broadcasting a full range of frequencies simultaneously, unlike an isolated A.C. frequency sine wave; So the spark can power the spinner starting at any R.P.M.! The spinner accelerates up this broad scale of frequencies.

Normally, we need to increase input power to accelerate the spinner. Here we have an asymmetric relationship; The input's constant, but the spinner speeds up as it climbs to the next higher frequency range. Constant input!

[Allen Burgess]

Kelvin-Helmholtz Waves.

"Faster waves traveling over slower waves generate "Kelvin-Helmholtz waves".

The electric buzzer should produce the "Self Accelerating" effect I noticed and set out to explain. An A.C. synchrounous signal will not propel the magnet rotor untill the R.P.M. matches the frequency.

The explosive acceleration from an interrupted spark is an OU effect I theorize is a magnetic Kelvin-Helmholtz effect. Normally, we have to add power to produce acceleration. The magnet rotor generates this acceleration power spontaneously from the interrupted spark longitudinal "magnet wave"'!

[Allen Burgess]

Electric Buzzer and Ruhmkorff Coil.

The two differences between the "Electric Buzzer" and the "Ruhmkorff Coil" are the inclusion of a capacitor between the electrode and breaker in the coil and a reversal of battery polarity:

The "Ruhmkorff Coil" has a small capacitor between the electrode and the breaker; However, this would kill the plasma vortex arc in the electric buzzer.

Capacitor,

"An arc forms at the interrupter contacts at 'break' which consumes energy stored in the coil, slowing the rate of change of primary current, reducing the output voltage. To prevent this a capacitor (C) of 0.5 to 15 μF is connected across the contacts to increase the speed of switching on 'break', producing much higher voltages.[dubious – discuss] It also prevents damage to the contacts by the arc. The capacitor and primary winding together form a tuned circuit, so on break an oscillating decaying sinusoidal current flows in the primary.[dubious – discuss] This induces a sinusoidal voltage in the secondary. As a result: the high voltage output pulse at each break actually consists of a rapidly alternating series of positive and negative pulses (left) which decay rapidly to zero".

The power coil connected in series between the electrode nail and the negative pole of the battery in the arcing spark gap electric buzzer should drive the diametric neo magnet spinner wild. Be prepared for shock velocity acceleration if you try this. Remember the PVC coupling protective housing, helmet and goggles!

[Allen Burgess]

Secondary.

Wrapping the "Electric Buzzer" primary tautly, then over lapping the primary with a finer wire secondary would generate a clean A.C current from induction, like a "Ruhmkorff Coil". This A.C. current should be able to assist the primary drive coil with a secondary A.C. synchronous power coil. The two coils should operate synchronously. A pulse D.C, A.C.. synchronous hybrid.

Below to the left is the "Make and Break" mechanisem of a Ruhmkorff inductor. The springy tin top serves the same purpose in the "Electric Buzzer"; Plus a schematic on the right:

[Allen Burgess]

Homemade electric buzzer.

This video has an awesome conclusion at 6:30 in the video, demonstrating the "Spark Gap" generator application of the electric buzzer broadcasting A.M. radio waves. The plasma arc is visable between the tintop and the iron nail. This simple oscillator would power a diametric rotor just like the oscillating Reed switch connected in series to a bifilar Tesla series connected solenoid power coil. This plasma arc is actually a spiraling R.F. vortex like the one pictured below:

The rotor may need to "Pony" up with a Reed swith oscillator coil. Both coils can fit through a protective PVC coupling from opposite sides.

https://www.youtube.com/watch?v=j3fvpIan5x4

I ordered a group of magnets from K&J magnets to a new P.O. Box down here in Costa Rica to try this myself with the "Frictionless Ludic Top" spinner featured above. I'll upload a video when it's working!

[Allen Burgess]

Frictionless bearing.

Here's a quite simple nearly "Fricton free" bearing:

https://www.youtube.com/watch?v=DB8tvnHq5qo

A diametric tube with a ball bearing on the bottom and a steel rod set in the top could easily hang suspended the same way as the top.

[Allen Burgess]

It is my understanding that the vortex between contacts involves not only the charge moving from one contact to the other, but also the interaction of the environment/aether. In this sense, it (reed switch) can be considered a means for imparting open an system character to the setup (despite being encased in glass), and would arguably raise its COP.
Bob

@Bob Smith,

Exactly Bob. Another thing is an inexpensive Reed switch is a better deal then a thousands of dollars Hotek Power Generator to reach those RF frequencies for the twin spiral ribbon coils. We just simply need to measure the frequency of the plasma oscillation first, then cut the ribbons to the correct length for the resonant spirals.

[Bob Smith]

It is my understanding that the vortex between contacts involves not only the charge moving from one contact to the other, but also the interaction of the environment/aether. In this sense, it (reed switch) can be considered a means for imparting open an system character to the setup (despite being encased in glass), and would arguably raise its COP.
Bob

[Allen Burgess]

Plasma vortex

There's a good video of a plasma arc at :10 seconds into this video inside an oscillating magnetic Reed switch:

This plasma forms a spiraling vortex, as pictured below, due to the magnet at the cathode end of the Reed switch contacts:

https://www.youtube.com/watch?v=1gI6taD9fiE

The spiraling plasma vortex sends a powerful spiraling electromagnetic wave into a wire coil if attached to one. This transmits a "spin wave" that can power a magnet rotor at high velocity.

[Bob Smith]

plasma reactions involving charged particles such as ions or plasma particles, possibly including nuclear fusion reactions".

Brilliant find Allen! Great quote. I'm assuming this is in reference to single strand flat spiral coils (as opposed to, say, the Series Bifilar spiral coil).

The phenomena associated with the spiral coil as per this quote result from finding and using the proper frequency and wavelength. My question would be whether in fact there is a coil topology with similar characteristics (to the spiral coil) which will act in the same way within a DC motor. Furthermore, I wonder if such a coil winding(s) would interact with a rotating magnet in such a way that it would enable the rotor to settle in to a set frequency (of rotation) from which these phenomena would naturally occur. In this sense, I am wondering if there is a way for nature to guide or govern this process within a specially wound DC motor that would also act as a generator at the same time.
Bob

[Allen Burgess]

A.C. frequencies.

From the patent: This Hotek RF power generator beats a crummy Reed switch:

"At AC frequencies of 10 kilohertz or greater, the common references to “alternating current” (AC) voltage begin using a different term, which is “radiofrequency” (RF) voltage. Accordingly, RF voltage is a form (or subset) of AC voltage, which operates at frequencies higher than 10 kilohertz. RF power generators are readily available, and are sold by numerous companies that can be easily located by an Internet search, using the term “RF power generator”. For example, Hotek Technologies Inc. (hotektech.com) sells two RF power generators, called the AG 1024 and AG 1012 models, which can provide output power at frequencies ranging from 20 kHz to 1 MHz; the 1012 model has a power output of 1000 watts, while the 1024 model has a power output of 2000 watts. The output frequency of any such RF power supply can be adjusted and “tuned” across the entire range of operating frequencies, merely by turning knobs or manipulating other controls in a power supply of this type ".

Hans Coler suggested that ferromagnetism is a fluctuation phenomenon with a frequency around 180 kHz.

Qote from "Magnetic Resonance Amplifier" inventor Norm Wooton:

"Joel and I were successful in isolating and identifying the fundamental Ferromagnetic Resonant Frequency as being around 174.9 KHz. Doesn't it sound ironic that this freq should fall so close to what the Corums have determined that Tesla designed his big coil out in Colorado springs around"?

[Allen Burgess]

plasma reactions involving charged particles such as ions or plasma particles, possibly including nuclear fusion reactions".

[Allen Burgess]

Back EMF.

"When a DC electric motor runs at high speed it wastes most of the applied voltage to the curse of back EMF". "Standard electric motors are horrendously inefficient"!

The "Plasma Vortex" electric motor would be completely free of the curse of BEMF inefficiency! It should exceed 100%.

I'm initiating a new thread entitled "Plasma Vortex Motor" because the evolved concept no longer involves a Reed switch.

[Wistiti]

Thank you Allen!
You give really good information!