Bedini Ferris Wheel Regauging Motor

[redrichie]

I found this book while cruising the internet Looking for info about ED. It is preview of the book. Scroll down to page 224.
Anti-Gravity and the World Grid - Google Books
Recently Dr Stiffler posted an exciter coil setup set of videos. A coil, by itself aligned in a N/S configuration produces a resonant frequency. Not sure if it will in an E/W config or not. But ED sure like the N/S direction. On his tool board he has a very long single wrap coil. the bigger the coil the more power could possibly be harvested. Maybe enough could be collected at the right time of alignments to run a motor. Not related to the above book but interesting

[John_K]

Bedini Ferris Wheel

Thanks alot for your expertice
Found a 25 volt cap, and now things are getting more interesting. Finished up the shield too, and it looks like that helped even more.
Dumping 2 times pr sec.
Im using 2 hi power led's and one 5.1 volt zener to trig the scr, Running at 21 rpm.
When using a scope to see the "ringing", where would you put the probe and the ground clip? I guess between the coil coil wires, but the scope thing is new to me, so I thought I would ask professionals
Best regards
erikbuch

Hi erikbuch,

Excellent, sounds like you are getting somewhere.

Scope between the coil wires, or the collectors of the NPN and PNP transistors.


John K.

[erikbuch]

Thanks alot for your expertice
Found a 25 volt cap, and now things are getting more interesting. Finished up the shield too, and it looks like that helped even more.
Dumping 2 times pr sec.
Im using 2 hi power led's and one 5.1 volt zener to trig the scr, Running at 21 rpm.
When using a scope to see the "ringing", where would you put the probe and the ground clip? I guess between the coil coil wires, but the scope thing is new to me, so I thought I would ask professionals
Best regards
erikbuch

[John_K]

Cap Sizes

Hi!
Tried alot, from 16 v 2200uf, 35 volt 4700, 50 v 6800. They all work, or so it seems on the led's. Dumping faster or slower depending on size and if i parallell two of 1 kind. Bit still no increase in batt voltage. Running now at 12 volt, with 1 35 v 4700. If i measure at the katode on the scr i ser about 23 volts before the dump.

I would use a 25V cap when running at 12V, a 50V cap when running at 24V and a 75V cap when running at 36V. Then choose the size of the cap to dump 2 or 3 times per second.

Try not to parallel the caps or you lose too much as no two caps are alike.


John K.

[erikbuch]

I was running the hall sensor inverted over the main magnets, now I have made a kind of timing wheel with round magnets, and getting much better results. Maybe the puls from the hall was to short to make any power from the coils. Strange, the potential was there over the cap, but when dumping to the batteri it sort of disappeared.
Ill just keep on fiddeling around with it, learning by doing

Best regards
erikbuch

[erikbuch]

Hi!
Tried alot, from 16 v 2200uf, 35 volt 4700, 50 v 6800. They all work, or so it seems on the led's. Dumping faster or slower depending on size and if i parallell two of 1 kind. Bit still no increase in batt voltage. Running now at 12 volt, with 1 35 v 4700. If i measure at the katode on the scr i ser about 23 volts before the dump.

[John_K]

Hi all!
How is your build's coming around?
Finally up and running with my wheel!!
Made all 3 coils, used bigger iron rods for the cores, havent got any welding rods just jet. No magnetfield shield mounted yet, and magnets on the wheel are maybe too small compared to the coils.
But it started at first try!
Still playing with coil placement and timing.
I'm using JohnK's circuit version 1.5. Two motorcycle batteries in series as primary,and 2 115 amp big ones in series as secondary. Tried different configurations.
Not sure about the cap dump circuit, the leds light up like in all your videos and the scr sounds like it is working, but when I measure the secondary bank it is only showing a tiny tiny increase when it is dumping.
It is charging, but very very slow,not like anything you guys are showing on your videos.
If I measure at the cap it shows about 35 volts before it dumps. Im sure it is just something I have misunderstood or forgotten or both, but I have been over the circuit 100 times, and tried different led's, caps, more zeners(in series) and several scr's of the same kind.(TYN816) Tried to play with it at 12 volt aswell, works the same way. Cant really see what I'm doing wrong here, or if it is just my batteries kidding me around. The motorcycle batteries are brand new, but 1 of the big ones are not 100 %.
Alot of fun anyway ;-) Thanks to all for inspiration and solutions!
I'll try to upload a picture later!

Hi erikbuch,

What size is your capacitor?


John K.

[erikbuch]

Getting there!

Hi all!
How is your build's coming around?
Finally up and running with my wheel!!
Made all 3 coils, used bigger iron rods for the cores, havent got any welding rods just jet. No magnetfield shield mounted yet, and magnets on the wheel are maybe too small compared to the coils.
But it started at first try!
Still playing with coil placement and timing.
I'm using JohnK's circuit version 1.5. Two motorcycle batteries in series as primary,and 2 115 amp big ones in series as secondary. Tried different configurations.
Not sure about the cap dump circuit, the leds light up like in all your videos and the scr sounds like it is working, but when I measure the secondary bank it is only showing a tiny tiny increase when it is dumping.
It is charging, but very very slow,not like anything you guys are showing on your videos.
If I measure at the cap it shows about 35 volts before it dumps. Im sure it is just something I have misunderstood or forgotten or both, but I have been over the circuit 100 times, and tried different led's, caps, more zeners(in series) and several scr's of the same kind.(TYN816) Tried to play with it at 12 volt aswell, works the same way. Cant really see what I'm doing wrong here, or if it is just my batteries kidding me around. The motorcycle batteries are brand new, but 1 of the big ones are not 100 %.
Alot of fun anyway ;-) Thanks to all for inspiration and solutions!
I'll try to upload a picture later!

[Rl2003]

Thanks Randy,
That's a great idea. I had not thought about that. I just found two thin
plates of round aluminum too. I was planing on using a thin cut dremel tool
but would need to mount it sideways on the CNC machine and rotate the
plate for each cut. That idea may save me some time.
Mark

Have you considered using 2 plates with the same size slot so that you can rotate one of them to get a narrower slot? The machine work would have to be quite accurate but it serve the purpose.

@ all

Very interesting thread. I have just finished reading it up to this point.

Some day I may be able to try building one, but for now the weather has just gotten good enough to begin to work out in the garage again. So I will be starting my runs on my SSG for advancement.

Randy

[minoly]

Dvd Efv 23

Ditto - Thanks!

Patrick

We just finished watching - re-watching re-watching....
anyone trying to build the re-gauging part of this, this is the vid. it does not get into the ckt but it does not look like that much of a stretch. the big stuff is everything else. In a hundred years I would not have put 1 and 1 together to make 1100 here.
very informative!

Patrick

[rbees]

This is one reason I tried the Opti switch instead of
the hall. I was able to get a faster on/off time with a small slot. I am looking for a
way to go even smaller, but have not had time to work on it latley.
Mark

Have you considered using 2 plates with the same size slot so that you can rotate one of them to get a narrower slot? The machine work would have to be quite accurate but it serve the purpose.

@ all

Very interesting thread. I have just finished reading it up to this point.

Some day I may be able to try building one, but for now the weather has just gotten good enough to begin to work out in the garage again. So I will be starting my runs on my SSG for advancement.

Randy

[gmeat]

Ok,I see 4 of you guys have ordered the dvd so surely 1 out of you 4 could send me a copy of it .many Thx in advance.


-Gary

[Ron Chase]

Dvd

Ditto - Thanks!

Patrick

Me to!

Ron

[minoly]

Thanks Brent,

I just ordered my copy!


John K.

Ditto - Thanks!

Patrick

[John_K]

Thanks Brent

Thanks Brent,

I just ordered my copy!


John K.

Hey All,

I was pretty excited to see the following anouncement...



We are pleased to announce the last DVD in the John Bedini trilogy covering the debut of the 12 ft. high monopole motor at the Renaissance Conference in November 2010.

Entitled "Tech Review," this one contains a private 84 minute lecture by John in his lab explaining in intricate detail how the multiple circuits and sub-circuits all work together harnessing what John terms "magnetricity."

All the tips and tricks are here that John didn't have the time to go into in such detail in the public forum.

Available from the DVD section of the Tom Bearden online store at The Tom Bearden Website - online store



May be what we have all been waiting for. Maybe this will help us decipher some of the riddles and questions that we all have been looking for! I will definitely be ordering this one!


Thanks, Brent