Muller generator replication by Romerouk

[blackchisel97]

Thanks toranarod Yes, MJL's need about .25A to stay in the right part of their curve. Makes sense, unfortunately...for me

BTW
I had no intentions to further ignite any argument by asking questions.


V

[Joit]

Maybe that is the trick at the Mosfets.
When i pulse an NPN like the 3055 i got Way lower Spikes as with a IRF540 or higher.
The NPN want to switch a bigger Amount of Energy reliable,
but when you use a Mosfet for a low Amount of Watts, like a Pulse creates,
the Mosfet can transform the Current better into Voltage.
Seems its the Base, what is faster saturated, even a Mosfet behaves more like a unpoled Capacitor regarding Base and Drain.

[toranarod]

speed

Maybe that is the trick at the Mosfets.
When i pulse an NPN like the 3055 i got Way lower Spikes as with a IRF540 or higher.
The NPN want to switch a bigger Amount of Energy reliable,
but when you use a Mosfet for a low Amount of Watts, like a Pulse creates,
the Mosfet can transform the Current better into Voltage.
Seems its the Base, what is faster saturated, even a Mosfet behaves more like a unpoled Capacitor regarding Base and Drain.

Yes speed is every thing.

The main primary function in this work is we are making DC pulse motors.
The one underlying function of all the OU devices that work with coils and neo magnets is instantaneous transition time from power on to power off. It is not acceptable to have any propagation delays. Some say you need to employ mechanical switching for the best possible speed like to old style point in your cars ignition system. Just too hard to control
and have a very short life span. With the advances in Hex FET and BiCMOS technology
we should be able to achieve some good results.

In electronics we call this the slew rate and all devices have a rated slew rate that they are expected to switch at.

In the photo below.



The variation between the red line and the green line is the delay time from off to on
Volts rise time per micro second.

I believe that the real OU will be available with hi speed switching at voltage ranges in 1000 volts and going up. I already have recorded data that shows more efficiency with higher voltages. And better COP using the same coils just high voltages. This is where I am slowly developing my electronics.
I have been buying up semiconductors from all over the world that have voltage ratings in the KVA range. With the death of the cathode ray tube all the big high transistors are going out cheap. So get them while you can.

Anyway that's what I am working towards.
maybe it will all go up in smoke like the FETS do lol

[Slider2732]

I'm on IRF630's now as a trial. If we have the need for 100ns switching or total time of pulse to draw aether energies, then MOSFET's are the way to go it would seem. IRF630's aren't that good, but i've found at least 1 or 2 on each old monitor circuit board (200V 9A).

Pulse motors run with them from 4V in my tests and the only difference to transistors being a 1K resistor on the Gate leg. Similar amp draw of just 8mA at 4V on a simple switcher circuit with a Hall.

[lota]

http://www.overunity.com/index.php?action=dlattach;topic=3842.0;attach=54280

Lota

[toranarod]

http://www.overunity.com/index.php?action=dlattach;topic=3842.0;attach=54280

Lota

Hello lota

welcome.. Nice circuit diagram.
keep us informed of you progress

good luck

[redrichie]

Did he do it? :
YouTube - ‪quest for OU XI -- "M-G long-runner"‬‏

[synchro]

Bruce's OU Claims.

Bruce,

I am willing to bet you any amount of money, and I can produce backers to help, that all your claims of generating any kind of verifiable overunity gain are completely false, and that you are the lier, not me! Now let's see how much money you can come up with to back up your malarky! I dare you.

Joit,

What's your explaination for the 2nd Hall?

[eastcoastwilly]

Bruce,

I am willing to bet you any amount of money, and I can produce backers to help, that all your claims of generating any kind of verifiable overunity gain are completely false, and that you are the lier, not me! Now let's see how much money you can come up with to back up your malarky! I dare you.

Joit,

What's your explaination for the 2nd Hall?

Please stop posting stuff that has absolutely nothing to do with this thread. There is Private Messaging for bickering and whatnot.

Thanks for your consideration,

Will

[Joit]

Joit,

What's your explaination for the 2nd Hall?

[synchro]

Null Points.

Quote from Bruce:

"A nice little write up posted by Nul Points at OU. Like I have said, there are many interesting things to be said about PLAYING WITH STRANDS...

Quote from Null Points:

"The darker and lighter lines represent the two windings, OF THE SAME SIZE WIRE, in which the first winding is connected in series to the second winding".

Null Point's experiment has nothing whatsoever to do with STRANDS. Null Point's experiment involves A SINGLE WIRE!

JOIT,

My understanding is there are 5 magnets and 9 coils. How can the magnets be 180 degrees apart when they're an odd number? Don't you think it's more likely the 2nd Hall is narrowing the pulse width like the 2nd reed switch in Ozzie Calanan's break even circuit, rather then supplying a second serial power pulse? Along with tapering the power pulse, the 2nd Hall can slmultaniously open the output gate.

Also, what's the "red button on top" comment you made refer to? You must think there's something real bright about useing Vacuum tubes in the age of the Arduino laptop programed ROM.

[Joit]

Quote from Bruce:

"A nice little write up posted by Nul Points at OU. Like I have said, there are many interesting things to be said about PLAYING WITH STRANDS...

Quote from Null Points:

"The darker and lighter lines represent the two windings, OF THE SAME SIZE WIRE, in which the first winding is connected in series to the second winding".

Null Point's experiment has nothing whatsoever to do with STRANDS. Null Point's experiment involves A SINGLE WIRE!

JOIT,

My understanding is there are 5 magnets and 9 coils. How can the magnets be 180 degrees apart when they're an odd number? Don't you think it's more likely the 2nd Hall is narrowing the pulse width like the 2nd reed switch in Ozzie Calanan's break even circuit, rather then supplying a second serial power pulse? Along with tapering the power pulse, the 2nd Hall can slmultaniously open the output gate.

Also, what's the "red button on top" comment you made refer to? You must think there's something real bright about useing Vacuum tubes in the age of the Arduino laptop programed ROM.

Synchro
Regarding Posting #743? Thats where i did Quote you. Is this to much for you?

Go Back and READ IT. Are You really only out for a Fight here?

You still use any of your Postings to put something in Where you can offend Bruce Further?

Man, go back to Ou.com, that Place there really fits for you.

[Joit]

Synchro,
How the Topic did start there, Romero stated, that it did not work with 2 small Pulses. He mainly agreed, that he used 4 Coils to drive, one Pair at Top, One Pair at bottom.
This Configuration from Romero has still a Drag on the Rotor, so it dont seems like, he did additional short one Coil more, even, it would not help really, when he has 7 other Generator Coils, and only one Coil short, to get higher Voltage, that dont work, because it will equal to the lower Amount at the Cap.
Plus it makes additional Drag on the Rotor. One Video what is out there from the Guy what drives a Rotor only with switches or Transistors is a Fake. That dont works.
Plus, the Circuit is not set like, that it would make Sense, to short only one Coil.

[admin]

We have noticed this thread going in a direction that is not respectful of the Forum Guidelines.

Please respect these Guidelines or we will need to take further action.

Thank you.

[Joit]

I wont read that again, but

"A nice little write up posted by Nul Points at OU. Like I have said, there are many interesting things to be said about PLAYING WITH STRANDS...

Quote from Null Points:

"The darker and lighter lines represent the two windings, OF THE SAME SIZE WIRE, in which the first winding is connected in series to the second winding".

Null Point's experiment has nothing whatsoever to do with STRANDS. Null Point's experiment involves A SINGLE WIRE!

Do you understand what TWO WINDINGS Mean? No Matter, if they are in Serie or Parallel connected ??
That means you HAVE 2 Strands. And NO MATTER, If this 2 Strands have the same Size.
Windings mean, You Place Wire OVER or CLOSE to eachother.

They get the Idea, but sorry, You dont.

And not matter, how they Call it, violating Lenz or Ohms Law, its both realated.
Even when you it Magnetic Resistance, not Lenz Law, well he describes it with his Law.
And a Resistance in a Circuit creates allways Back Electro Magnetic Force,
no matter, how you create it, over a Phyiscal Resistance, like a Neon Bulb
and the Wire in there, or with a additional Coil, where the Current runs opposite, or you short it.

That may even would work with a simple Coil with a lot Windings with Thicker Wire on it,
and a smaller Wire inside, or at one End from this Coil.