SR 193 / SR193 - Study of the Device, Theories, Diagrams, Schematics & Experiments

[vidbid]

Pre-SR193 Device Video Comparisons

The SR device is not complicated and I think I have the basic process along with a bunch of other people out there.

People just need a place to work where they are not divided and conquered which is what overunity.com does. They should change the name to the end of unity.com. The mass media controlled by the money changers works the same way with the right / left BS.

People have tried to disclose at OU and been banned in seconds along with their posts deleted. They shut down notifications so nobody gets the information in their email if they think someone is going to disclose.

I just watched that happen to quarktoo by pirate and have seen it happen before. People should be aware of that kind of thing.

Hartman banned all the smart people that were working together and then they were herded to OUR and that is another mess of sorts. I'm not sure what that is all about.

That copper tube running up through the center is the key to slowing down a longitudinal wave produced by the spark gap. The modulation is a very weak field but when the atom is suddenly tipped, it gives of a strong EM field as the Fe goes through Fe56 > Fe 54 transmute.

Wear some good safety glass and keep some distance if you want to avoid cataracts - the device is a BETA emitter.

SR stated something about how it was a diode destroyer. I suspect that would be the case but we can get around that through old passive devices that are not used much anymore. Notice how the bulb got so hot it started the paper on fire? The electrons are still going too fast?

Lastly that device has not been replicated and so he does not deserve and credit for anything. I would not pander to people that suppress OU and SR is one of them. I have no use for them at that Russian web site. The domain name exists yet is not registered. Odd?

You're not the only person to report about Hartman.

The problem is there is no way of knowing whether the blue rectangle in his pre-SR193 device video is a copper tube or not.

I know about the phenomenon with respect to a metallic tube in a core of ferrite rings. How if a certain frequency is applied to the metallic tube in the core of ferrite rings, that a voltage across the metallic tube can develop a voltage across it.

One thing that I have recently noticed that if you compare SR193's pre-SR193 device video to his current SR193 device video. In the pre-SR193 device video, you can see in the middle of the coil a tan wire. That same tan wire can be seen in his current SR193 device video. I wonder if he just used the same coil?


Tan Wire in Pre-SR193 Device Video


Tan Wire in Current SR193 Device Video

I believe that the diode destruction problem can be overcome by using high voltage schottky diodes.

[mlurye]

I have simple question. Which coil causing transistors to be heated so much?

[vidbid]

Russian Analysis of SR193

Video of Russian Analysis of SR193

Real Strannik Forum - Thread about the SR193

[vidbid]

Heating Issues

I have simple question. Which coil causing transistors to be heated so much?

Where did you hear that a coil was causing transistor heating?

[mlurye]

Where did you hear that a coil was causing transistor heating?

There 2 clues on the video that transistors are heating 12V fan and very big heat sinks. And vidbid, if you think it's not a coil that causing heating, what is?

[vidbid]

Cooling

There 2 clues on the video that transistors are heating 12V fan and very big heat sinks. And vidbid, if you think it's not a coil that causing heating, what is?

I'm aware of the heat sinks and that the transistors need to be cooled. As to what actually causing the heating, I'm not ready to jump to a conclusion, but do believe that the heating issue could be mitigated by a future successful re-design of the circuitry for the modulation component of the device.

As for now, the cooling fan seem to be sufficient in the short term.

[vidbid]

Message from SR on April 4, 2010

I found this quote which was quoted by Duff on the OU forum.

From his quote, I am deliberately not going to post information about the technical side and in principle the work of the installation that would not get information 'free riders', I take away from it that SR is suppressing the technology.

From his quote, I want to keep some 'dress code' access to information that is under the 'dress code' refers to the level of thinking, I take away from it that SR only wants certain 'worthy' people to understand the technology.

SR's way of thinking is short-sighted, narrow and parochial. It is sort of the same way that E.V. Gray thought; only E.V Gray didn't want anybody other than himself to understand his technology. Greed, paranoia and pride won't take care of the people's energy needs.

You need to free yourself from the old way of thinking.

Think open source, public domain, and free.

[vidbid]

Earlier SR193 Prototype

These images are from this video.









I'm only speculating as to the connections.

[Dr Poppy]

To assume the SR device works seems to skip past the first and most important step. To attempt to ignore that first step seems fundamentally wrong.

I'm going to speculate that two of the wires go to a power supply and that the device does not self run and he is a fraud and here is why.

He claims to have spent a lot of time with Kapanadze yet does not seem to have a clue how the kapanadze device works.

The Kapanadze device is a magnetic gas generator. The transformer scheme is called a coaxial transformer which is used to convert high frequency FR power.

Under the blue tape of the TK device is copper tubing. A gas is in the tubing and when the polarized atom is hit with a HV pulse, it aligns and becomes magnetic.

The SR device uses no gas container that is visible or copper tubing. He does not even seem to know that the wire running up through the center makes it a coaxial transformer.

Sorry Vidbib but... FAKE!

[mlurye]

Here is rough explanation how system should work:
"Дросель после разрядника для сглаживания тока (так же искра получаеться тихая). Регулируемый зазор в ферите для получения разных резонансных частот на половинках сердечника и получения ~50Гц на вторичке. Последнее ето сизнхронизация катушки подмагничивания с частотой биения и получения эфекта электромагнитного усилителя."
Add tuning up and synchronization.

[bolt1]

I suggest you don't need half the electronics in this device to discover the fundamentals. There are no short-cuts and no books to explain how its done nor trying to trace wires is a waste of time no matter how simple it appears on the surface. Without a full schematic and construction details everything else is just a wild guess.

Remember now when JLN released Kapagen as demo? He did not release the circuit for quite some time and how many hundreds of ideas came out of that when in fact it as just a MOT wired on conventional voltage doubling mode and a spark gap? BTW im in no way relating the two only indicating that something hidden in a box is hidden and no amount of guessing will reveal the truth until you build it or its fully disclosed.

So here are the fundamentals. You need an HT supply of low power 15kv is enough at very low current. Anything that makes an arc will work. Use a Joule thief, modified camera circuit anything that provides electrons into the system.

You need a small AC transformer about 12 volts to inject AC at 50/60hz. This test removes all the push pull transistors as not required for realisation.

What you have left are coils, inductors, ferrite, earth wire, perhaps some copper pipe and a good imagination to wire it such a way the HT is modulated by the 12 VAC through the inductance wired in such a way as to provide asymmetric modulation and reduced lenze.

This is what SR193 did FIRST! (See early vid compared to later looped)

Then you build the looping electronics LAST after the basics have been realised in the inductor.

You will KNOW when you are ready because quite simply the bulb will be lit to perhaps 3 to 5 times brighter than the energy supplied by the power supplies. NOW you can build the 50Hz simple inverter and cap banks ready for looping.

[vidbid]

Replication Short Cut

I suggest .... cap banks ready for looping.

Yeah, I was thinking along the same lines.

I was thinking about Magnetite instead of Ferrite cores. I think I can manufacture Magnetite or at least fe3o4 inexpensively.

[scratchrobot]

Found some interesting video's, I think it is from SR?

YouTube - Kapanadze effect 1.mp4

YouTube - Kapanadze effect 2

Scratchrobot

[vidbid]

SR193 Videos



SR193 Video #1 The single coil & spark gap on SR's distinctive rug.

SR193 Video #2 SR's experiments with a energizing a coil which is affecting a compass.

SR193 Video #3 SR's Kapa-Budenyi Test #1.

SR193 Video #4 SR's Kapanadze Experiment. This video shows SR taking two ferrite cores out of the coil tube assembly.

SR193 Video #5 SR's De La Morto Test #1. In this video, SR shows the dead-spot in electric field along side of output coil with his LED capacitor indicator.

SR193 Video #6 SR's De La Morto Test #2. Again, SR is showing the dead-spot in electric field in the middle of the output coil with his LED capacitor indicator.

SR193 Video #7 SR's Kapanadze Effect #1. In this video, SR has a detachable secondary coil connected directly to a small lamp load. There is a compass nearby spinning counter clockwise while the output coil is being pulsed.

SR193 Video #8 SR's Kapanadze Effect #2. He removes ferrite core from coil tube. See Russian video about the effect of one pulsed ferrite core on another ferrite core. The Video has an English translation in the subtitles.

In my opinion, there are two ferrite cores (air gap in between them) in the coil/core assembly (the Tube) of the current SR193 closed-loop device.

See air gap between the two ferrite cores. Image supplied by admin of Next Energy forum:


SR193 Video #9 SR's Next Installation Video. This device looks like T. Kapanadze's design. Note SR's distinctive rug on the floor in this video.




SR193 Video #10 SR's Video of the Closed-loop System

See Russian Translation of RealStrannik Forum about SR

Conclusion: I have watched everyone of the above videos. Video #4 shows SR removing two ferrite cores out of the coil tube assembly. This leads me to believe that SR is utilizing an air gap between the two ferrite cores, much like the video showing the split double e-core by Andrey Melnichenko.

In video #5, SR shows the dead-spot in electric field along side of output coil with his LED capacitor indicator.

I am speculating, but could this be where the air gap is between the two ferrite coils? Again, speculating, but could SR be using the effect in this video? It's funny but the name on the video is Andrey Melnichenko. It can't be by the Russian businessman and billionaire Andrey Melnichenko.

Conceivably, it might be possible to create a device that can take advantage of harvesting the back emf from coils(1), and also obtain additional energy from radiant events(2), while utilizing the split double e-core principle involving "triblets"(3), and taking advantage of the effect of virtual infinite impedance on a primary resonance LC filter circuit(4).

1. Harvesting the back emf from coils: Bob Teal's Magnipulsion, Peter Lindemann Attraction Motor. See Electric Motor Secrets.
2. Energy from radiant events: See The World of Free Energy by Peter Lindemann.
3. Split double e-core: See Andrey Melnichenko's Split Double E-core Video.
4. Virtual infinite impedance: Introduction to Resonance Video, Energy Propagation Video

[vidbid]

RECEIVING Ferrite HAVING LOW POINT

I found this Russian paper on properties of ferromagnetics from a Russian forum I was reading.



PS: Selected Posts:



Why the SR193 device output core gets hot, I think. Source: Post 92