Motor Generators

[BroMikey]

Here is the right teaching spirit

Linear Power Supplies and the Filter Capacitor

Meters can not properly measure power if DC is unfiltered. Choosing random caps is worthless

Doing the math Dave needs 3400uf to run his 4 amp Dc motor off 60hz less than $15 bucks

https://www.ebay.com/itm/19337926627...QAAOSwntlg0b2s

Now doing the math from a 1100hz AC source if Dave wanted to loop his system and get an accurate meter reading he would need only 150uf, probably use a 220uf

https://www.ebay.com/itm/20368196721...EAAOSwRKthgHkw

or
2200 X 12 divided into 4 amps = .000151uf

[Turion]

https://www.youtube.com/watch?v=jsxroTt9IhY

https://www.youtube.com/watch?v=VuqiiOj_Pj8

Fun to look at

[BroMikey]

Here is the right teaching spirit

Linear Power Supplies and the Filter Capacitor

Meters can not properly measure power if DC is unfiltered. Choosing random caps is worthless

Doing the math Dave needs 3400uf to run his 4 amp Dc motor off 60hz

[BroMikey]

Ancient water wheel free energy engine. Pump water for the Pharaoh

[BroMikey]

Nikola Tesla's Mysterious Electricity Generator

[BroMikey]

If you generate using an induction motor remember a 12vdc battery can be used the start the motor generating. With this system off connect a 12vdc battery to the caps for 10 seconds 4-6 times, then start it up. In this way you don't need to plug the motor into the wall first. All motors setting around will lose their residual magnetism. I built this and it works great, however after 2 years it stopped generating till I used a small battery in this way. A battery charger works too.

.

[BroMikey]

Motor - Generator

You need 5 Lpm HHO generator to run a 3hp motor/engine

[BroMikey]

Self charging systems. In this demo recharging is done at 13.9amp @ approx 70vdc or 970watts while not dragging down the bike motor. This is a break even bike ride

[BroMikey]

Sorry to hear that bro. Hope all goes well for you.

Thanks Dave, first I got to have prostate work done. Can't go.

[Turion]

Sorry to hear that bro. Hope all goes well for you.

[BroMikey]

Greetings and that everything goes well for you, we want to see you here, so that you continue contributing and sharing your experiences and knowledge, and your projects.
May the blessing of the creator cover him in his mantle of light always

Thanks Alex

[alexelectric]

Me too, I was stuck on the road all day till 7 oclock. The Doc is sending in for open heart surgery.

I hope your coils pan out and your EV gets fixed.

You guys all pray for me

Greetings and that everything goes well for you, we want to see you here, so that you continue contributing and sharing your experiences and knowledge, and your projects.
May the blessing of the creator cover him in his mantle of light always

[BroMikey]

I had to take my Polaris EV to the city today to have it worked on, and that basically killed my day.

Tomorrow I have to go back and pick up parts I wasn't notified were in until I got all the way back home.

I am also going to try two other coils, just for fun.

Me too, I was stuck on the road all day till 7 oclock. The Doc is sending in for open heart surgery.

I hope your coils pan out and your EV gets fixed.

You guys all pray for me

[Turion]

My plan has ALWAYS been to loop the machine, but first I need to get these coils outputting close to the expected output. I had to take my Polaris EV to the city today to have it worked on, and that basically killed my day. Tomorrow I have to go back and pick up parts I wasn't notified were in until I got all the way back home. So I am taking two coils to my partners to run on the old machine and verify the output both unloaded and under load on the old clunker. And I will continue working on the machine I have to see if I can get the coils to go all the way in. I am also going to try two other coils, just for fun. Lots to do and not enough time to get it all done.

[BroMikey]

MickeyMouse, at this point i have lost all respect for you. ,

still haven't seen a looped machine


you should be scared. Not of me,

but of the moment when you stand before god and have to come face to face with everything you did in this life, including spreading all your lies.

You might find a market of sheep there that might follow you on your journey with the devil.

So now you will claim I am beyond help and going to the devil? nicesurmon. All because my views don't line up with the university religion. God is not damning people dude, Jesus saves. Didn't you know? Your attack of me on a personal level only shows you as a low class individual.