Basic Free Energy Device

[altrez]

hi all.after lots of trial and error i finally got the floppy hub motor running like the computer fan.using power twice and running smooth and fast.
this motor has 2.7 ohms dcr for each phase,4 coils,and was harder to tame.here's the circuit.147 uf for c2.r1 is 1000 ohms.r2 is 500.curious, but that's how it goes.
pic 2 is a proposed motor gen setup for 2 output phases.
i got an emax rc motor coming from china.said to be .15 ohm dcr.looks like it has neo magnets. hopefully i can get that to run too.
will add a pic of the hub motor motoring asap.
cheers.

Nice work! Thanks for the update.

-Altrez

[voltan]

hi all.after lots of trial and error i finally got the floppy hub motor running like the computer fan.using power twice and running smooth and fast.
this motor has 2.7 ohms dcr for each phase,4 coils,and was harder to tame.here's the circuit.147 uf for c2.r1 and 2 are 1k.diodes are 1n5189.there are 12 coils and 16 alternating poles in the hub.
it's a bit crude and could do with some improvements.it's a bit fiddly to start and the circuit wants to flipflop.the current draw is minimal when it's doing this and you just give it a good flick to start it.it starts and runs from 9-10v and up.it's a bit sensitive in that adjusting the timing lights with vr1 changes the rpm.hopefully this sort of timing circuit can be adapted to run any brushless PM motor with a few tweaks.
next step is to try loading the generator side of it.i think i will need a switchable capacity setup to make changes to c2 on the fly.
pic 4 is a proposed motor gen circuit for 1 driven phase and 2 output phases that are wye connected and center tapped.
i got an emax rc motor coming from china.it is said to be .15 ohm dcr and it looks like it has neo magnets.
cheers.

[altrez]

Hello All,

Last night I added my first transistor to the 3 battery Tesla Switch it seemed to work really well. On the DvD John shares a schematic of a three battery Tesla Switch running a lamp and explains in detail what's going on.

The next thing i need to do is get bigger transistors as I melted a few I am going to hook the 6 volt and 12 volt up on two different tables so I can run both at the same time. My logging equipment will log up to 10 volts for the 6 volt switch and I will order a 50 volt version for the 12 volt switch.

This is the second level of testing on the concept of the Tesla Switch for me and is a very important part judging from the results last night it looks very promising.

For everyone who is following along theses are the steps I would recommend you take to get started on the Tesla Switch.

1. Buy the DvD TESLA SWITCH

2. Get some batteries that are NEW.

3. Start with manually changing the battery position at a set time.

4. Add the transistor this will make a lot of sense once you watch the DvD.

At that point you will have a very good idea of how this switch works.



-Altrez

[altrez]

Hello,

Once I started working on the Tesla Switch I came to the conclusion that I needed a good easy way to check the batteries that I was charging as the load. I purchased a cheap battery tester from Amazon a few weeks ago that I have been really happy with.



It allows me to test a battery after a run and see if it really has a good charge or just phantom voltage from the run. It has helped me out greatly.

The way I test is I wait for the load battery to reach a certain voltage, after it hits that voltage I let it rest 15 minutes and monitor the voltage. If it remains stable I test it with the Battery test that adds a small load to the battery. If it drops really quick I know it needs more time.



-Altrez

[altrez]

Altrez,
If I were you, (and I will be working on this within a month or so) I would be looking at a five battery system. You already know that when you are rotating the three batteries you can get longer run times, but you want to have a battery that has been charged by an outside source (your generator) to rotate into the mix, as well as a battery that has rested after charging. We know that battery 2 is the battery that loses the most voltage and needs to go to position 3 to be recharged, so when battery one moves to the second position you move your rested battery to position one and your externally charged battery to the rest position. Battery 3 comes out to be externally charged.

Now this is all only necessary if we can't run the motor (powering the generator) on the potential difference between the generator output (as if it were the two batteries together) and a battery. Can we build a gen run by our modified motor that puts out enough volts and amps to loop our setup.

Hi Dave,

Back about 10 pages ago I wrote out one of the setups that I was going to test and it worked pretty much the same way using 3 3 battery setups. Right now I am pulse charging a fourth battery at 60/40 cycles.

So far I can't prove that I have had any logger run times even though it seems like I have. After this week I will know for sure if I pass the four hour mark on the batteries I am charging running an inverter with a load of over 50 watts.

I know we can build a generator that will do that. And we will build a generator that will do that. Here is my strategic goals for this project.

1. Identify an easily reproduced ultra efficient power source for the BFED.
a. Tesla Switch

2. Build three types of pulse motors.
a.Matts razor motor mod
b.Qc Motor Generator

3. Generator with 12 pickup coils

4. Output system

Thats what I have come up with so far and its easily a years worth of daily work.. I have a total budget on this project of $7000.00. I have spent almost a grand so far. The big thing for me is documentation with data that has been logged. from the runs. I need to spend another grand just on my data logging equipment alone.

My next steps over the next few weeks are to get a simple working build of the Bedini tesla switch in both a 3 and 4 battery setup plus a 6 and 12 volt setup. Have it run for a week with no manual switching and log everything.

I feel if I spend the most time perfecting the energy source for the BFED then it will afford me some mistakes on down the road.



-Altrez

[Turion]

Altrez,
If I were you, (and I will be working on this within a month or so) I would be looking at a five battery system. You already know that when you are rotating the three batteries you can get longer run times, but you want to have a battery that has been charged by an outside source (your generator) to rotate into the mix, as well as a battery that has rested after charging. We know that battery 2 is the battery that loses the most voltage and needs to go to position 3 to be recharged, so when battery one moves to the second position you move your rested battery to position one and your externally charged battery to the rest position. Battery 3comes out to be externally charged.

Now this is all only necessary if we can't run the motor (powering the generator) on the potential difference between the generator output (as if it were the two batteries together) and a battery. Can we build a gen run by our modified motor that puts out enough volts and amps to loop our setup.

[altrez]

Good Luck!! LOL

Matt

Go BIG or Go HOME! LOL



-Altrez

[altrez]

Hello All,

I have been working on the same three batteries over the last 4 days. I keep thinking they are done but can still get a bit of charge out of each switch. I am giving them longer rest periods now.

Here is a pic from the current test setup.



Now the odd thing is that some times for no reason the energy out of nowhere will jump up.

Here is the series connected batteries voltage at the start on the run.



10 minites later it jumped up to this:



It slowly drops back down after that to around 20 volts. I am going to keep testing until I can not charge the load battery any more.

Might take a while lol.

I am moving forward with the Tesla switch. I am ordering more parts and meters. The plan is that if I can work on it daily for the next 6 months I should have it working correctly and fully documented with detailed graphs / pictures / videos and deep understanding of how it works and why it works.

I am going to take all that information and put it into a PDF with a parts list that you can get anywhere and with enough detailed instructions for it to work 100% of the time!



-Altrez

[Turion]

The original Matt Jones pulse motor pdf says to use #23 gauge wire, I believe 50 turns with a single strand, and with that you can build Matt's original pulse motor design. It's an awesome little motor and I have been using it for a year. You can use that motor with a 3 battery setup to see proof of concept, and it WILL WORK.

HOWEVER

Matt has been working to put together a motor for you guys that is faster, has more power than the original off the shelf motor (because of no back emf), and returns MOST of the used voltage to the battery so that we can use it (almost for free) to run a generator. This design is based on the things we have learned about how to make it work, and is somewhat different from the motor in the pdf. THIS NEW motor design will use #24 wire and will not be wound the same as in the pdf. May NOT use the same number of turns, and MAY use multiple strands

TWO DIFFERENT MOTORS but BOTH based on the MY1016 Razor Scooter motor.

Matt has been testing and testing, and has burnt up a couple motors in the process, as is to be expected. But what he thought would work DOES WORK. He is just trying to make it as efficient as he can, as powerful as he can, before he shares it with everybody. He doesn't want anyone to spend the money to try and fulfill his fantasy. He wants them to be replicating something he has tested and KNOWS beyond a doubt will actually work. SO it may be a few more weeks. Probably after the first of the year. Then you will know haw many strands, how long the pieces should be, and how many turns to put on each segment. We will put together a new pdf.

I keep telling Matt to take pictures as he winds these things so he has them to share when he is done. But he gets busy and probably forgets. LOL

The important thing is we know it works, and are just trying to make it better

Dave

While I am here, does anyone have a little generator that puts out 24-36 volts rectified to DC?? Has anyone tried substituting the generator for the two 12 volt batteries in the 3 battery setup and running a motor on the potential difference between the generator output and the battery? Now what if the motor you were running was the motor used to turn the generator??? Put an inverter on the battery and run some loads off it.

[Zardox]

Magnet wire

Dave
In post #336 you state to get some 24 gage wire. However the PDF says 23 gage. Just wondering if it matters or which one is better.

[altrez]

@Altrez, I have to disagree. With that mindset you fall into the 130+ year trap of science. Batteries are a electrical, potential sink or gate. They can, and have lasted decades, providing dipole differential beyond the chemical engineers wildest expectations. You just have to use that potential in the right way. This is the purpose of the Tesla Switch, 3BGS, Bedini Monopole, and soon Basic Free Energy Device.

Good Luck,
Randy

Everything I have been studying even the new DvD from John says that they will eat up all the carbon and zinc so with that in mind they are indeed in my mind at least a fuel source.

-Altrez

[tachyoncatcher]

Battery's are a fuel source and with that in mind they wont last forever.

@Altrez, I have to disagree. With that mindset you fall into the 130+ year trap of science. Batteries are a electrical, potential sink or gate. They can, and have lasted decades, providing dipole differential beyond the chemical engineers wildest expectations. You just have to use that potential in the right way. This is the purpose of the Tesla Switch, 3BGS, Bedini Monopole, and soon Basic Free Energy Device.

Good Luck,
Randy

[altrez]

After testing the last 2 days I have found with this test atleast that the run time is below simply running 3 batteries in parallel when using manual switching. I am going to order some more parts and try to get the automatic switching working.

-Altrez

[altrez]

After a bit of sleep I am back at it this morning. I had at least one battery die on me last night. So I just spent another $400 on a Battery Analyzer from BK.

http://smile.amazon.com/gp/product/B000LDMG08/ref=ox_sc_sfl_title_2?ie=UTF8&psc=1&smid=ATVPDKIKX0DER

I need to understand every last little bit of whats going on and why.
At this point I just want to make sure I have a way to really look deep into the inner working of the switch.

I seem to be making good progress and hopefully will have some real data to post soon. I do think I am going to go to the 4 battery setup as Bedini shows in his DvD after I get the 3 battery setup stable.

-Altrez

[altrez]

Working in the lab late tonight but I wanted to share something I have learned while working on the Tesla Switch. Battery's are a fuel source and with that in mind they wont last forever.

I am sure you all already knew that but its the first time I looked at it in such a way.



-Altrez