Newman Motor Finally Explained?

[clarence]

Next step attaching the magnets

Looks good and interesting.

That vendor's work looks as to have spared you a lot of time plus good balance. Always better to leave that to the pros.

After the rotor is good then the coils? Always the balancing isn't it. Right coils and rotor.

We need to rent a really large seaside bungalow, invite these energeticforum builders and sit around exchanging ideas and sippin your favorite.

Sippin my morning favorite coffee,
wantomake

Good Hearing From You Wantomake,

Yes The machinist was a Real PRO and his work was Excellent.
My next step is to finish the drill and tap and then install the magnets.
Then the unit Surround framework will be fabricated and assembled.
Included in the Framework will be the Commutator Assembly with its Dual
16 bar commutators and brush assemblies.

The last Items will be the Single Coil - Parallel Capacitors - And series 9.5 volt battery banks .

All of this will take awhile so won't be posting for awhile. Not that it matters anyway. All I've seen members do is take a quick look and blast on by like a
dust Devil! (Looking for a Quickie that has no cost and doesn't require any time!) Sad!

Well, time to get with it - daylights Burning.

Happy Sippin! I know I will.

Respectfully,

Clarence

[wantomake]

On the right road

Hello Wantomake,

Received Hex Shaft Back this AM.
Will do some drilling and tapping for magnet placement through the night.
Just going step by step.
Pic's below.

How's the sippin?

Best:
Respectfully ,

Clarence

Looks good and interesting.

That vendor's work looks as to have spared you a lot of time plus good balance. Always better to leave that to the pros.

After the rotor is good then the coils? Always the balancing isn't it. Right coils and rotor.

We need to rent a really large seaside bungalow, invite these energeticforum builders and sit around exchanging ideas and sippin your favorite.

Sippin my morning favorite coffee,
wantomake

[clarence]

Back from shop

Hello Wantomake,

Received Hex Shaft Back this AM.
Will do some drilling and tapping for magnet placement through the night.
Just going step by step.
Pic's below.

How's the sippin?

Best:
Respectfully ,

Clarence

[clarence]

One step then the next

Good Monday morning my ole friend!!!!
Coffee and a new week go together.

I will be very busy and not posting for a while. Trying to list our house to sell and purchase another larger house and shop.

The shop is four times larger than mine. Two garage doors cement floor. Working hard to get all things done. I could just imagine how many unfinished projects would fit in that empty shop!!!

Still checking in from time to time.
wantomake

Hello and greetings back to you friend.
As a trial step to attach the mags to the 1 3/4 inch height hex shaft I found that to get 3 North mags and then 3 South mags as JWN shows and did it can be done but unless attached in place as it is done - they are HIGHLY UNSTABLE and WILL always un-attach themselves into stacks of three of their own making. (That is a real B to undo then!)
To prevent that I KNOW that each mag will have to be attached one at a time to IT"S location by a # 8 countersunk steel screw.
MEANING each flat LENGTH (17 inches) will have to be laid out EXACTLY and
then drilled and tapped For 8/32 NC screws.
Six flats for each mag with it"s 2 countersunk holes = 16 Drill&Taps per Flat
@ 6 Flats = 96 TOTAL Drill&Taps!!!!!! GOING TO BE REALLY SLOW!!!

All of this BEFORE I take it to the machine shop!
Probably going to be a LOT of coffee between now and back from machine shop event!

OH WELL - one foot in front of the other.

Happy Sippin Ole Friend !

Clarence

[wantomake]

@ ALL,

Will do updates - But will be SEVERAL weeks or so
simply because it takes me time to get things done.

Respectfully,

Clarence

Good Monday morning my ole friend!!!!
Coffee and a new week go together.

I will be very busy and not posting for a while. Trying to list our house to sell and purchase another larger house and shop.

The shop is four times larger than mine. Two garage doors cement floor. Working hard to get all things done. I could just imagine how many unfinished projects would fit in that empty shop!!!

Still checking in from time to time.
wantomake

[clarence]

Updates

Yes keep us updated Clarence and please upload some pictures if you will.

Regards,
pjotterkjen

@ ALL,

Will do updates - But will be SEVERAL weeks or so
simply because it takes me time to get things done.

Respectfully,

Clarence

[pjotterkjen]

Will keep YOU informed as progress (good) takes place.

Yes keep us updated Clarence and please upload some pictures if you will.

Regards,
pjotterkjen

[clarence]

For me it"s back to jwn blue print and instructions

Hello ole friend!!
Glad you're still building. Sitting here in South Carolina rain just started but the coffee is good.

I was very excited back when I first built the toy size Newman motor. There is much more to be explored and understood with this invention. Too bad lack of prosperity prevented the larger build.

Share as you can here. I know this forum is not kind sometimes, but like the human mind it can be evil or an instrument to build, support, encourage others and lead.

I'm watching and know you are the later.
Always a pleasure my friend,
wantomake

Hello Wantomake Ole Friend,

I have had to completely dismantle my first replication and start anew.
The first just did not cut it.
So this time I will follow His Diagram and instruction to the letter!
Ordered and received my steel hexagonal shaft which is 17 inches long.
Will take it to the machine shop next week and a half to have the 5/8 steel round shafts installed in each end and retained by a 3/16 torsion pin.
Have the 1.5 UF 2000 volt capacitors to harness the BEMF and keep the
9.5 volt incremental battery bank more than charged. Have the magnets already and the sufficient wire spools (20 AWG) for coils also.
Will use the same commutator set up as the first but it will a TWO commutator system same as His.
Also the commutator system and the magnet system will be TWO separate
units and simply Coupled together as He stated.

Will start out with just one coil as He showed and will add the others as He advised also.

All will take some time - but that goes with the course!
Will keep YOU informed as progress (good) takes place.

Thanks for the support Ole Friend!

Respectfully,

Clarence

[wantomake]

Good coffee and success

Hello ole friend!!
Glad you're still building. Sitting here in South Carolina rain just started but the coffee is good.

I was very excited back when I first built the toy size Newman motor. There is much more to be explored and understood with this invention. Too bad lack of prosperity prevented the larger build.

Share as you can here. I know this forum is not kind sometimes, but like the human mind it can be evil or an instrument to build, support, encourage others and lead.

I'm watching and know you are the later.
Always a pleasure my friend,
wantomake

[pedroxime]

Thank you Clarence !!

[vidbid]

New Energy Series Vol. 3 Joseph Newman

New Energy Series Vol. 3 Joseph Newman

https://www.youtube.com/watch?v=irUXauA16Vg

[clarence]

Real commutator real brushes

@ ALL

These are Available !
Heavy Duty - work well.

Respectfully,

Clarence

[maxc]

I've been using pencils for my brushes. Been getting 10 milliamp back spikes.

[wantomake]

@ ALL

It is MY Firm belief that the # figure was used to designate ALL TYPES of descriptions with reference to Weight or Turns or whatever. J.W.N.
expected those interested to use their brains and NOT make assumptions.

I am well into my unit - right now I am having Machine Shop work done on
my hexagon shaft. The shop work should be complete in about 2 - 3 weeks.

As usual, this Ole Fart is loving it ALL.

Respectfully ,

Clarence

Hello Ole friend,
Sipping hot coffee and reading your post is my favorite hobby this early morning.

I hope you success with this build. I only built the toy size way back when. I saw and learned much from that small unit built only from 4" pvc union. It's good to see your email from time to time.

Count my membership in the Ole Fart club.

wantomake

[clarence]

Added info

@ ALL

It is MY Firm belief that the # figure was used to designate ALL TYPES of descriptions with reference to Weight or Turns or whatever. J.W.N.
expected those interested to use their brains and NOT make assumptions.

I am well into my unit - right now I am having Machine Shop work done on
my hexagon shaft. The shop work should be complete in about 2 - 3 weeks.

As usual, this Ole Fart is loving it ALL.

Respectfully ,

Clarence