Use for the Tesla Switch

[rosehillworks]

[QUOTE= Those big switch's with the driver are expensive and if you make even little mistake they go. Ask Rosehill
Matt[/QUOTE]

You that got wright.! After a few $400 runs Matt was a real budget saver
start small do it wright and you will not be disappointed

[Turion]

I'm going to build the small one first, since I have everything to build it already on my shelf except the Radioshack transformer, which I've ordered and the Stamp. So not much out of pocket expense.

I figure to build the large one right will cost at least $600.00, and I want to do it right the first time. (That includes a whole spool of wire, but I figure it won't go to waste, since I'm sure I will be building more of these.) Building the small one will give me the experience with how it operates, and won't be as costly if I make some learning mistakes. When I've got it up and running, I'll build the big one. So I'm in no hurry. I'll sit back and learn from the small one before I give the big one a shot. It will also give me a chance to get all the parts in before I start building.

Thanks again Matt

David Bowling

[Matthew Jones]

Matt,
I have been looking for some good switches for this project. What do you think about these

http://www.pwrx.com/pwrx/docs/cm300dy_24nfh.pdf

If they are a go, I found them here Powerex Result
David Bowling

Ya David those will work but you have to get the powerex driver kits for them. And don't fool yourself they'll burn up if you do not set them up right.

I will have literature to cover the wiring with those switch's,in general.

But before you run out and buy those you may want to just get a few small relays 50 amp or something to make sure you can get the thing wired up and running. Those big switch's with the driver are expensive and if you make even little mistake they go. Ask Rosehill


Matt

[N O G]

Digit Tesla switch

Hi there Rosehillworks , Matthew , Bits and others ,
Nice work there fellas , Keep up the brilliant work . cheers Jason

[Turion]

Matt,
I have been looking for some good switches for this project. What do you think about these

http://www.pwrx.com/pwrx/docs/cm300dy_24nfh.pdf

If they are a go, I found them here Powerex Result


David Bowling

[vrand]

Thats because I haven't given the instructions out yet... Just a shopping list of parts.

Its all coming.

Matt

Thanks Matt, we are all looking forward to it

Cheers Mike

[Matthew Jones]

Thats because I haven't given the instructions out yet... Just a shopping list of parts.

Its all coming.

Matt

[vrand]

I gave you link to both the transformers I recommend. One is for a large setup one is for a small setup.
Stop drinking so much coffee and slow down when you read the shopping list.

NO FERRITE, NO TOROID.... Just plain old iron plate cores, for starters.

Matt

Hi Matt, the instructions didn't mention stripping out the wiridings on that 3kw transformer and winding the L1 to L3 coils on it with the 6 AWG square wire.

How many turns/length of feet of wire are for the L1 to L3 coils?

Cheers Mike

[vrand]

This is it 3000 Watts Step Down Voltage Converter Get it disassemble it and rewind it with #6 AWG wire.

Ah okay, thanks.

Cheers Mike

[Matthew Jones]

Thank you William for sharing your research and results

Matt wrote that there are 2 transformers A & B below?

A- Transformer. 1 -3 KVA or 1000 to 3000 watts. BIGGER IS BETTER.
3000 Watts Step Down Voltage Converter

B- #6 AWG Square magnetic wire at 150 ft, OR #14 awg magnetic wire at 300 ft. Now you can use anything in between the 2 listed wire. But do not go smaller than 14 awg, and DO NOT THINK you can wrap 5 strand of 20 awg together to come up with that size. This a recipe for HEAT and does not work well. You cannot use insulated wire either, this is also a recipe for poor inductance.

Or you can use A or B?

If you need both, what do you wrap the 6 AWG square wire on, iron core or ferrite core? Toroidal core for high frequency? What is the frequency of the operation of switching?

Cheers Mike

I gave you link to both the transformers I recommend. One is for a large setup one is for a small setup.
Stop drinking so much coffee and slow down when you read the shopping list.

NO FERRITE, NO TOROID.... Just plain old iron plate cores, for starters.

Matt

[rosehillworks]

What type of core do you use for L1, L2 & L3?

Cheers Mike

This is it 3000 Watts Step Down Voltage Converter Get it disassemble it and rewind it with #6 AWG wire.

[vrand]

I used a 3 KVA 3000 watt transformer with an iron core. Use the 6 AWG square wire on L1 L2 and L3. The transformer is the one that Matt has posted in his list

What type of core do you use for L1, L2 & L3?

Cheers Mike

[rosehillworks]

Thank you William for sharing your research and results

Matt wrote that there are 2 transformers A & B below?

A- Transformer. 1 -3 KVA or 1000 to 3000 watts. BIGGER IS BETTER.
3000 Watts Step Down Voltage Converter

B- #6 AWG Square magnetic wire at 150 ft, OR #14 awg magnetic wire at 300 ft. Now you can use anything in between the 2 listed wire. But do not go smaller than 14 awg, and DO NOT THINK you can wrap 5 strand of 20 awg together to come up with that size. This a recipe for HEAT and does not work well. You cannot use insulated wire either, this is also a recipe for poor inductance.

Or you can use A or B?


If you need both, what do you wrap the 6 AWG square wire on, iron core or ferrite core? Toroidal core for high frequency? What is the frequency of the operation of switching?

Cheers Mike

I used a 3 KVA 3000 watt transformer with an iron core. Use the 6 AWG square wire on L1 L2 and L3. The transformer is the one that Matt has posted in his list

[vrand]

Mike
That build is mine. The out put is 3000watts. Matt was vary kind in helping me getting it to work!!! I hope to post some test soon. I did not used the right wire so I have to wind it again with #6 transformer wire. Matt is right about the heat in the transformer so use what he said to use
[ATTACH]8950[/ATTACH]

Thank you William for sharing your research and results

Matt wrote that there are 2 transformers A & B below?

A- Transformer. 1 -3 KVA or 1000 to 3000 watts. BIGGER IS BETTER.
3000 Watts Step Down Voltage Converter

B- #6 AWG Square magnetic wire at 150 ft, OR #14 awg magnetic wire at 300 ft. Now you can use anything in between the 2 listed wire. But do not go smaller than 14 awg, and DO NOT THINK you can wrap 5 strand of 20 awg together to come up with that size. This a recipe for HEAT and does not work well. You cannot use insulated wire either, this is also a recipe for poor inductance.

Or you can use A or B?

If you need both, what do you wrap the 6 AWG square wire on, iron core or ferrite core? Toroidal core for high frequency? What is the frequency of the operation of switching?

Cheers Mike

[rosehillworks]

Thanks to Matt it works

Mike
That build is mine. The out put is 3000watts. Matt was vary kind in helping me getting it to work!!! I hope to post some test soon. I did not used the right wire so I have to wind it again with #6 transformer wire. Matt is right about the heat in the transformer so use what he said to use.

The caps I used are 18,000 uf x 7=126000uf