Peter Daysh Davey Water Heater Query

[PhysicsProf]

Where is everybody?

I took the attached photo today. It shows stainless steel vessels in various geometric shapes (including cylindrical and spherical) which I have begun using to test Davey sonic boiler concepts. Most of these shapes already have a small hole so that I can connect wires to the vessels as well as connecting them in various relationships. I have a number of nylon nuts and bolts and spacers for this purpose.

The parameter space is large! it will take me awhile, but I have begun the testing (see for instance, a test run earlier in this thread).

[Slovenia]

Message from Mr. "C"

Yesterday I made a similar sonic boiler original of which has a COP = 1.4 but is easilymade from the original. This boiler is not better than the originals because it is not in itself another electrode at 50Hz, which is very hard to make would have to be from 0.1 mm thick titanium or a very hard steel.
Regards to all replicators of sonic boiler.

[PhysicsProf]

From Prof. Savic (Mr. "C"):

Message from Mr. "C"
Yesterday I made a similar sonic boiler original of which has a COP = 1.4 but is easilymade from the original. This boiler is not better than the originals because it is not in itself another electrode at 50Hz, which is very hard to make would have to be from 0.1 mm thick titanium or a very hard steel.
Regards to all replicators of sonic boiler.

Thank you for this input and encouragement to replicators!!

You show CIRCLES in your diagrams. Are the SPHERES or cylinders? and -- what is the DIAMETER?

Thanks again.

[weeb1e]

I found this quite a long time ago, but only rediscovered it again now. Perhaps this could be usefully implemented where there is existing mechanical power?

An over-unity mechanical sonic resonator: FUELLESS HEATER NO FUEL NO GAS NO WOOD NO GREEN HOUSE GASES - YouTube

[wrtner]

Bench grinders

Those in England who have a branch of Lidl reasonably nearby
and who are tuning bells, bowls or tubes to a frequency should
note this:

LIDL Great Britain - lidl.co.uk

They are on sale from February 6th to around 10th after which
they are gone. Sometimes limited stock.

Paul-R

[boguslaw]

Those in England who have a branch of Lidl reasonably nearby
and who are tuning bells, bowls or tubes to a frequency should
note this:

LIDL Great Britain - lidl.co.uk

They are on sale from February 6th to around 10th after which
they are gone. Sometimes limited stock.

Paul-R

There is nothing at that link

[wrtner]

There is nothing at that link

They want you to put in your local postcode. Try nw2 1qq

[Slovenia]

Configuration of can and tuning setup.

[boguslaw]

Configuration of can and tuning setup.

Nice.We are thining the same way this is exactly the way I cut can and I regulate distance between can and my cover cup .

[Slovenia]

Misunderstood

I misunderstood what he meant for us to do and had removed the bevel from my cans entirely. You did good!!

Nice.We are thining the same way this is exactly the way I cut can and I regulate distance between can and my cover cup .

[boguslaw]

I misunderstood what he meant for us to do and had removed the bevel from my cans entirely. You did good!!

No, you didn't. At least I think that original schematic was suggesting that can has to be cut evenly without leaving bevel intact.But I had no tools to do that so I did what i did ;-) Only hand china tools here Such cutted can is very steady stiff comparing to the can with bevel removed.

Try such experiment : ping a can hanging it by rod attached to the bottom center as per schematic and then gently rub around the edge (polished! do not cut yourself) with any soft but hard rod like wood stick covered by cloth for example. You will hear similiar sound like in singing tibet bowl.

[wrtner]

Don't forget that you can tune a cylindrical item by cutting a groove
in it. Dave Lawton uses this for his developments on Stan Meyer's
electrolysis gear. Also, this is used for tuning organ pipes. See the
paragraph on scroll tuning and the rather scruffy picture of
sopmeone's work:

Pipe Construction

Paul-R

[osamaricu_te]

Savic`s boiler tests

@PhysicsProf

Any news to update us on the device you received and how about the test? I read on your other topic that you had Savic device shipped to a fellow researcher in France and he was going to do the tests and you stated we will get some results soon.
Just wanted to ask if you got the device, is it tested and what are the results?

In case you answered this on another topic I apologize but I couldnt find it.

Thanks

[RAMSET]

[osamaricu_te]

O Te
Be assured, Providence has been set in motion.........
With the goal being to make this world a better place!

Thx
Chet

Since when do you go by nick of PhysicsProf ?

My question was directed specifically to Prof.Steven and not to you.

As direct as I am, my questions are also direct and additionally simple, if PhysicsProf finds time, I am sure he will answer, thats all I asked.

Thanks

P.S. While I took a break on this device/topic, I worked on FRICTION HEATER by lloyd tanner.
Assembled working prototype (smaller version though) and tested it.