The Robert Adams Pulse Motor Design Review

[lanenal]

Robert Adams Components

cheers rod

Thanks for putting that up, very tidy. I noticed in your circuit there is no collection of back emf from your driving coils (L1 & L2). The cushion is probably provided by the capacitor, but why is there a resister R1? What if we replace R1 by a diode D1? Just a wild suggestion.

cheers lanenal

[toranarod]

The comments above about the Adams motor being mainly for heat was the original intention but as time went by Robert learned how to harness the electrical charge directly from the cooling water. This was a big improvement and much simpler to do than using boilers and turbines connected to generators and far more efficient. There is a charge in the cooling water that is probably very much like a static charge and can be extracted quite simply. You have built the Adams motor with neos instead of ferrite magnets and there is a lot of useful power to be gotten from that setup but I never ever built those machines. Robert told me the first time I met him not to waste my time with those designs but to build only the thermo motor. I am sure you guys using digital timing techniques are on the right track as timing is critical to these machines but the higher voltages produce stray currents that can wipe out low voltage digital equipment so you will need to be very careful with shielding and earthing techniques I think. The real radiant or Aetheric energy operates almost the opposite to everything you have been taught about electricity so keep this in mind when the obvious does not work the way you think it should.
I would like to see the timing setup you have as that is what I need to do with my motor.
Thanks for your great posts.

[toranarod]

Thanks for putting that up, very tidy. I noticed in your circuit there is no collection of back emf from your driving coils (L1 & L2). The cushion is probably provided by the capacitor, but why is there a resister R1? What if we replace R1 by a diode D1? Just a wild suggestion.

cheers lanenal

[lanenal]

Rod, thanks for going through all these trouble providing so much details and writing up so much for the record here. But it seems you are not settled down on the design yet (I know there are tough decisions to make to come out with a great design, probably even a lot of tinkering around too), I'll look forward to a finallized design with much patience (probably I have got no other choices at this point). Once again, thanks a lot for sharing this with us!

cheers, lanenal

[toranarod]

Rod, thanks for going through all these trouble providing so much details and writing up so much for the record here. But it seems you are not settled down on the design yet (I know there are tough decisions to make to come out with a great design, probably even a lot of tinkering around too), I'll look forward to a finallized design with much patience (probably I have got no other choices at this point). Once again, thanks a lot for sharing this with us!

cheers, lanenal

[toranarod]

I did draft a solid state circuit but My current condition stop it right there
but I had this on paper.

I can only show you the circuit its not been tested

[lanenal]

Sorry to learn of that mishap, hope you'll recover soon. Meanwhile, this might be a good opportunity to do some pure thinking...take good care of yourself.

[toranarod]

Sorry to learn of that mishap, hope you'll recover soon. Meanwhile, this might be a good opportunity to do some pure thinking...take good care of yourself.

what do you think about a combination of the Adams Motor and the effect of the Wankel motor

[bugler]

toranarod would it be possible for you to collect all the information about what you have accomplish so other people can faithfully replicate it?

Thanks.

[ashtweth]

Yes Rod has donated a PDF to the Panacea uni should be upon Sunday just have to compile the updates

Ash

[bugler]

Yes Rod has donated a PDF to the Panacea uni should be upon Sunday just have to compile the updates

Ash

Amazing news.

In a couple of years I hope to finish studying electronic engineering and start replicating devices such as this.

Thanks.

[qvision]

Hi Rod and thanks very much for sharing.

I've spent all this week constructing an Adams motor. I use ferrite magnets because i am at low voltage, i read that neos should only be used if your input is 120V or higher.

I have a single stator and no generator coils.

I am using the Bedini SSG circuit in order to get natural timing as well as avoiding burnt out reed-switches.

I need to make a new base though because, when i go above 7.5 volts, the centrifugal force is so strong the resulting vibrations are enormous, this thing really has some torque due to the depth of the rotor magnets.

I just set it going on a battery-charging test at midnight tonight and will report back.

In the meantime i am perusing your setup with interest.

<EDIT>

By the way, what voltage/current/power are you getting out of the generator coils ?

</EDIT>


Thanks,

Gary.

[toranarod]

I excited to see another up and running

Hi Rod and thanks very much for sharing.

I've spent all this week constructing an Adams motor. I use ferrite magnets because i am at low voltage, i read that neos should only be used if your input is 120V or higher.

I have a single stator and no generator coils.

I am using the Bedini SSG circuit in order to get natural timing as well as avoiding burnt out reed-switches.

I need to make a new base though because, when i go above 7.5 volts, the centrifugal force is so strong the resulting vibrations are enormous, this thing really has some torque due to the depth of the rotor magnets.

I just set it going on a battery-charging test at midnight tonight and will report back.

In the meantime i am perusing your setup with interest.


Thanks,

Gary.

I will be following your motor with interest as you could imagine will be looking forward To your results with much anticipation.

Please keep us up to date with the details. Sounds like the timing of the pulse is on track.
I observed Vibration was a good indicator the collision of the magnetic fields is a good result of correct timing. this is where the beginning of cold current flow starts.

With out any test equipment I could use this as a guide just to start the setup.

Can you share some more details of the specifications of your construction?

I have my motor running today too, doing some more tests.

Good luck

[qvision]

My setup details :

1. Rotor, from a VHS player.
2. Rotor magnets are 20mm wide, 50mm high, 5mm deep. I have these in groups of eight, each group superglued together to act as a single magnet. I have four groups on the rotor.
3. Drive coil is a serial bifilar wind. Trigger wire is 0.2mm, power wire is 0.25mm. Ferrite core is a rod, 7mm in diameter.
4. Drive circuitry is Bedini's SSG circuit.

I did a quick generator coil test using a coil i had lying around, 0.3mm wire and the same ferrite core as above, the coil's resistance being 28 ohms (i know that's way too much but this coil was just handy). I got 3.46 VDC (rectified) at 0.0025 Amps.

This is by no means a good build ! But it's battery-charging performance is looking superior to the SSG.

I will build a more precise machine in the new year, i am thinking of using my PWM to drive it :

http://www.rmcybernetics.com/files/pdf/PWM-OCXI.pdf

Gary.

[ren]

Hi Rod,

good to see another aussie in here. Where are you located if I may ask?

Ive built a few window motors and monopoles in my time, Im interested to know if you ever built John Bedini and Ron Coles bipolalr circuit, as the 1/2 circuit version of this is very close to an adams motor design.

I am working on a large rotor at the moment that will use the 1/2 circuit with hall sensors as timing devices.

Good work

Regards

Ren