F.M.Chalkalis gravity system a donation!

[nvisser]

Free Energybesslerwheel forum

Mr. Chalkalis.
Will you be so kind to tell us how you measured the output of the machine.
Regards
Vissie

[lespaul109]

i have a short video also at :

YouTube - chalkalis replication 1

[elias]

Welcome

Hi Mr Chalkalis,

to the forum, All of the people here have an open mind, and when someone approaches with a new idea, it is always welcome, but you know, I don't know what the difference of your device with a simple rotating pendulum is, and why should it draw energy from gravity? What I am completely sure now is that we cannot measure anything about your device with Newtonian mechanics, as it is designed in a way that cancels everything out. If you have a new theory or at least an insight about your device, that why or how should it work it is welcome.

Any help or of yours is highly appreciated ... and of course we do appreciate what you have offered, but we don't understand it.

Elias

[Matos de Matos]

i have a short video also at :

YouTube - chalkalis replication 1

http://www.energeticforum.com/renewa...how-i-see.html

[lespaul109]

My single outer drive wheel.....hope it works

[lespaul109]

another video, working this time

YouTube - chalkalis replication 2

[Matos de Matos]

another video, working this time

YouTube - chalkalis replication 2

It works; nice prototyping.
Can I suggest tracks on the pendulum to drive it at different radius?
You can measure the different velocities versus input, and output.
I am curious to see that generator working.
Keep up the good work.
David

[lespaul109]

with this variant that I made, it can only be driven from the outer edge, i tried to incorporate two wheels as he did but couldn't make it work....yet

[lespaul109]

now is the time when I ask for ideas about how to extract energy(electrical).........anyone

[torpex]

Hi all

now is the time when I ask for ideas about how to extract energy(electrical).........anyone

My suggestion:
Use a cheap stepper motor as a generator. Shafts can be connected mechanically between your device and the motor.
The output is AC, can be rectified with diode bridge for use as DC.
Remember to adjust the load to measure performance.
Example of a motor extracted from an EPSON inkjet printer:




Regards

[lespaul109]

great idea, got some of those too!

[lespaul109]

stepper motor help

ok, tested my motor that has two coils. Each produces 8v peak to peak @ 300rpm. My drive motor needs about 3v @ 600mA can some one tell me how to wire both coils using diodes and/or rectifiers and caps to power my DC motor? Color codes are:

Coil 1: Yellow & Black
Coil 2: Red & Grey

thanks,
jake

[Matos de Matos]

with this variant that I made, it can only be driven from the outer edge, i tried to incorporate two wheels as he did but couldn't make it work....yet

What I mean, is on the picture below.
Tracks on the sides to drive it at different radius.
After you test the load on the shaft, you can put a wheel similar to the drive on the load generator and test different configurations, drive on the top and generator on the smaller radius, and vice versa, to see if any gain driven and load at different radius.
David

[woopy]

Hi Lespaul and all

Bravo for the good work

As i cannot see how to use the pure gravity action on the shaft, i decided to try to replace the pendulum of my Milcovic 2 stage oscillator with the Chalkalis system.
It works pretty well. I did not made any measure to see if there is something here, but it is fun to see the movements. Very complex and everything is interactiv.

What do you thing, any idea to make measurements

Good luck at all

Laurent


YouTube - 20100725182421

[Matthew Jones]

Hi Lespaul and all
Bravo for the good work
As i cannot see how to use the pure gravity action on the shaft, i decided to try to replace the pendulum of my Milcovic 2 stage oscillator with the Chalkalis system.
It works pretty well. I did not made any measure to see if there is something here, but it is fun to see the movements. Very complex and everything is interactiv.
What do you thing, any idea to make measurements
Good luck at all
Laurent
YouTube - 20100725182421

Thats a descent setup. How much actual torque do you have at the end of your Milcovic setup?
If you could in turn drive a crankshaft that geared out to a generator, you might see a gain if the Milkovic setup has a high enough COP.

Matt