my smith kanapadz replication

[Xenomorph]

Uploaded with ImageShack.us

Good thought.
I am familiar with that document, but this little coil can´t KICK anything.
It´s way too small. According to that document the 6 turn coil in the green box device is the kicking coil, now compare that to that little tiny coil...

[vidbid]

SR 193 SR193 : HV Flyback Coil & Transistor





Reference:

[vidbid]

SR 193 SR193 : Blue & White Vertical Coil

What if the Blue & White Vertical Coil is being used as a feedback coil and driving the HV Formation Module and in some way is establishing the frequency and phase for the Frequency Generator Module?

[Xenomorph]

Funny Coincidence i also just wondered about the base wire.
There is some confusion as to what that circuit board really is that is to the left of the coil. It seems to provide the sinusoid signal for the transistors. And is obviously then not the HV signal generator.
But why is it being fed by the 220 Volt transformer via the grey capacitor?
And how is it initially being able to run?
To feed the 220 Volt transformer you need the sinusoid signal for the push-pull which in turn can´t be created without juice from the 220 Volt transformer ??? I am confused lol

EDIT: This cannot work, the grey big cap must have another function than to be the supply for the board.
According to convention the board (which seems to be something off the shelve [can be wrong]) has a red and a green wire
which might indicate the plus and minus rails, they are soldered to the white and the blue wire that lead away towards
the input caps. Okay there is still the theory of that little coil, but these wires being the power supply for the board is the only possibility really.




Uploaded with ImageShack.us



Uploaded with ImageShack.us



Uploaded with ImageShack.us



Uploaded with ImageShack.us

[vidbid]

SR 193 SR193 : White Wire from the Base of NPN Transistor. Where Does White Wire Go?

I believe that it (the white wire from base of NPN transistor) must go to the output of the Frequency Generator Module.

By the way, I do not believe that the curved gray line is a wire. I believe it is the edge of the upper plexiglass platform.



Correction: date on image should be 2010.06.26.

[Xenomorph]

Look at the first image of my last post, it goes down to the circuit board.
In the hi-res picture version it can be seen pretty clearly.

The question mark in the pic was not intended to mean anything concerning the gray wire (it is the glass table edge for sure) , but i know what you mean.

The function of the capacitor connecting the 220 Volt transformer to the frequency generator needs to be investigated.

[vidbid]

SR 193 SR193 : The Gray Cap

[Xenomorph]

That could be actually, i see a green wire next to it. Also the cap would be connected to a tapped output of the transformer (in the center of the winding) which would be weird. I initially thought that bend would be a tap lead. Well hard to tell from the pics.

I am actually investigating the set-up so intensely because i thought that something important might have been missed , but until now this all seems too simple and ordinary hehe.

[vidbid]

SR 193 SR193 : The Gray Cap, Wire & Frequency Generator Module

[vidbid]

SR 193 SR193 : The "So-call Relay" May Actually Be A Transformer

[vidbid]

SR 193 SR193 : The Gray Cap Connected To Green Wire

[vidbid]

Not Related to SR 193 SR193 : YT Video TomB455 Show How He Make His Kapa Gen

to TomB455

YouTube - D.I.Y. KapaGen.wmv

Wouldn't it have been awesome if SR193 would have shown us how to build his device like this guy?

[vidbid]

NOT SR 193 SR193 : Slotted Copper Tube in Core

I found someone using a slotted copper tube and ferrite rod.

YouTube - Utilization of energy from Tesla transformer.AVI

It looks like he used of both increase power available to the load.

[vidbid]

Not Related to SR 193 SR193 : YT Video : Light Up Bulbs With Tesla Coil

I saw this on YT. Maybe it will help me figure out what is going on with the SP193.

YouTube - Опыты с трансформатором Тесла

[vidbid]

SR 193 SR193 : Not All Photos Have Light Bulb Black Lead Attached to Output Coil Grnd

I've been looking at some of the photos of the SR193, and I have been noticing that in some of the photos the light bulb (black) wire is not connected to ground lead on the output coil. It's as if in some of the photos the device has been posed.