William F. Skinner - 1939 Gravity Power

[sly3000]

easier way to output

Aaron my idea is to transmit mechanical energy form the rotation of lower output weight directly , i know there is an oval , but this oval i am not sure if there going to be a big degree or not, But this is not a problem ,i think this should be determined by experiment

[Aaron]

demo video

Hmmmm.
Maybe my previous meccano attempts were built wrong.
Here's what I discovered...which maybe the wrong way to build it ?

Tom, that is a lot to take in. Can you put up a demo video on youtube?

[goldpro]

I can't make a video right now.
I see gotoluc over on the other forum has beat me to it.
see his 2 private videos on page 15 and 16.
they pretty much get across what I'm talking about although there
are some differences.

My intuition tells me I don't have it quite correct and I need to introduce more loosly coupled ideas instead of directly coupled.

I went back to the beginning and rewatched your whole video again.

I'm still concerned that the lever tip in a gimbal won't start the machine.
If it's spinning just a bit then yes I can see it would accelerate it and keep it going but starting it??.

I noticed also that filming the starting is missing. I might conclude that
it took a while and the camera guy didn't want to waste time on it.

watching the film for the millionth time I noticed that the translation plate only looks to be about 4" square or so. It's about the size of skinner's hand.
Maybe a key to the machine's successful working is that the offset between the lever tip and lower weight top is kept quite small. Maybe my model is offset too much. In twirling the lower weight model around by hand I know that I can get it spinning faster with less tilt, but we have to get it started and going with a bit more tilt.

There sure is a lot of different variables and math to consider to come up with a working machine but if Skinner did it then we should be able to do it too and come up with improvements once we grasp all the important details.

I'd like to ask about Jim Murray's ideas. At one point on his video he talks about the model he built that looks like a motor with a bent or flexible shaft that went out and connected to the perimeter of a larger wheel. He said that if the motor shaft went around once the other end of it went around twice and that it was a physical impossibility. Or words to that effect. point of reference was all important...etc . Can you elaborate on that and can we use it in the machine or are you already using it and I haven't noticed?

back to the meccano model.
Tom

[purelyprimitives]

I'd like to ask about Jim Murray's ideas. At one point on his video he talks about the model he built that looks like a motor with a bent or flexible shaft that went out and connected to the perimeter of a larger wheel. He said that if the motor shaft went around once the other end of it went around twice and that it was a physical impossibility. Or words to that effect. point of reference was all important...etc . Can you elaborate on that and can we use it in the machine or are you already using it and I haven't noticed?

back to the meccano model.
Tom

Hi Tom,

Here's a video that explains the epicyclic effect that Jim Murray observed. Skip to the part with the two coins and you'll see the 2:1 relationship.

https://www.youtube.com/watch?v=dfhiwNK7rC8

[goldpro]

Thanks very much for that video.
It makes me wonder if instead of a clutch Skinner used an epicyclical gear train and the lever he grabbed altered the planetary arrangement to give a different ratio/speed to the input rod levers after the whole machine had started to turn slowly.

[gotoluc]

I can't make a video right now.
I see gotoluc over on the other forum has beat me to it.
see his 2 private videos on page 15 and 16.
they pretty much get across what I'm talking about although there
are some differences.

Tom

Hi everyone,

I have not been posting at this forum topic because I didn't want to disturb Aaron's suggestions since I was not convinced of the mechanics of Mr. Skinner's device.
First I wanted to try some things that I observed which were different then what Aaron was suggesting. I'm not going to go over it here so you would have to read the OU topic to understand the reasoning.

I have made those tests and have eliminated those possibilities and now mostly agree with what Aaron has shared as to the mechanical movements needed.

Here is the links to my first test video with NO universal joint to the bottom shaft and a circular movement to the upper leaver.

Part A device: https://www.youtube.com/watch?v=00xIxEQqRsk

Part B device working: https://www.youtube.com/watch?v=WF-ZlkBw46g

Here is the link to my newest test video WITH universal joint to the bottom shaft and a circular movement to the upper leaver. Notice I can stop the rotation of the two shafts and the top lever rotation plate continues to turn freely. So a bearing in the mid plate may not be needed.

https://www.youtube.com/watch?v=Hvy7zuWKaF4

With the universal joint added the device performs more like seen in the original Skinner film but the load is still reflected back to the prime mover. I tried everything I could think of and finally decided to take the upper lever out of the circular drive and turn it by hand while the bottom generator is under load (bulb).

By turning the lever in a circle motion I could feel an equal pressure throughout the 360 degrees and the bulb load would not light.

By turning the lever in an elliptical orbit the top weight would fall and cause a change in angle to the mid plate which would make the bottom weight swing around and the bulb would light for that moment. There is a pressure point at the turning points of the elliptical orbit but there is also an acceleration when the top weight falls, so it may come close to being neutral to the prime mover (other than friction losses) but this remains to be tested.

Now looking for recommendations on how I can easily convert my top gear so the lever is turned in an elliptical orbit to further test this possibility of being the right thing.

I will now post future video and updates to this topic as I'm now going the same direction that Aaron has started the topic with.

Luc

[goldpro]

Luc,
In your latest version is the lever rod free to rotate inside the bearing at the top of the lever rod...the one on the drive wheel? or is it fixed so it can't?
Tom

[gotoluc]

Luc,
In your latest version is the lever rod free to rotate inside the bearing at the top of the lever rod...the one on the drive wheel? or is it fixed so it can't?
Tom

Yes Tom, the top lever is free to turn in the top bearing I specially made which is attached to the drive wheel. Made it that way from the very beginning.

Luc

[goldpro]

Before going elliptical, would you care to change it so the lever is fixed/secured somehow so it can't rotate on it's own axis?

The square tube/bar you have the top weight on should be as parallel to the upper drive wheel as possible before securing the lever from spinning.

see my previous post #179.

then it will be just like my meccano model.
Tom

[gotoluc]

Before going elliptical, would you care to change it so the lever is fixed/secured somehow so it can't rotate on it's own axis?

The square tube/bar you have the top weight on should be as parallel to the upper drive wheel as possible before securing the lever from spinning.

see my previous post #179.

then it will be just like my meccano model.
Tom

If I could do this, what do you think this will do and prove?

Luc

[goldpro]

I'm not sure what it will prove.
I think the meters would tell us if there is any gain from a
full scale build using this principle.
It might tear apart the enclosure if you turn up the voltage too high.
You could see if less input voltage could drive it as well as the voltage you've been using.
I'm in uncharted waters.....
Tom

[seychelles]

Hi guys watching this video from one of the greatest invention of our time..THANK YOU MR SKINNER WHERE EVER YOU ARE IN THIS UNINIVERSE..THANK YOU and thank you to the guy who put this video to our attention.. I am going a different path , I have send this video to an engineering firm in western Australia to reverse engineer it ..I told the guy there I do not care how much it cost I will see it COME TO A WORKING PTOTOTYPE..Yes I might be a fool I am 52 years old I have seen a lot of very interesting invention in my life time but this one is PURE GOLD .. again THANK YOU MR SKINNER WHERE EVER YOU ARE IN THIS UNIVERSE..

[wrtner]

Hi guys watching this video from one of the greatest invention of our time..THANK YOU MR SKINNER WHERE EVER YOU ARE IN THIS UNINIVERSE..THANK YOU and thank you to the guy who put this video to our attention.. I am going a different path , I have send this video to an engineering firm in western Australia to reverse engineer it ..I told the guy there I do not care how much it cost I will see it COME TO A WORKING PTOTOTYPE..Yes I might be a fool I am 52 years old I have seen a lot of very interesting invention in my life time but this one is PURE GOLD .. again THANK YOU MR SKINNER WHERE EVER YOU ARE IN THIS UNIVERSE..

It is a video; that's all.

It could be fake. Thousands of them are.
.

[hal.freeman]

I want to ask permission to aaron, artoj and gotoluc to use your videos/images in a editing i am doing with the key concepts explained in portuguese, to start this thread in our (newly created) brazilian forum. Let's see if we can get people excited towards replicating this...

I am excited to do it myself, but haven't started it yet. I'm not good with mecanics , so i'm seeking help from friends and waiting till i get an idea of how much it'll cost.

Thank you aaron for bringing our attention to this wonderfull machine

and of course thank you skinner

[goldpro]

I have send this video to an engineering firm in western Australia to reverse engineer it ..I told the guy there I do not care how much it cost I will see it COME TO A WORKING PTOTOTYPE.. THANK YOU MR SKINNER WHERE EVER YOU ARE IN THIS UNIVERSE..

Why not hire Aaron and Artoj since they are already doing the reverse engineering already?