Bedini Ferris Wheel Regauging Motor

[darkwizard]

good work Woopy, that scope is telling something, look at the radiant spike, it looks very good, with that tiny input, i think you have something there.

[John_Bedini]

Bedini GT3

Woopy,
Good video nice spike. If you would build the Bi-Polar switch you would be free of that supply. Then it would be easy to tap the energy to the cap and switch it back.
John B

[rosehillworks]

spike ?

John B. Is this how it works. Do we switch on as magnets are coming in, switch off before tdc collect the spike let magnets pass collect the spike. Then use collected energy to power the next switch ? Thanks william

[John_Bedini]

Bedini GT3

William,
The energy is collected after the trigger, then collected to the capacitors.
Chuck H will call you in about 15 m
John B

[Web000x]

you want to self bias this from the pulse

I like your line of connections with the Bedini Ferris Wheel Motor. I would have loved to attend the conference but was busy working just to pay bills. Maybe I can save some money and come to the next one.

This post has really got my attention because it seems to encompass all of the key points that Charles Steinmetz and Eric Dollard discuss as far as understanding the importance of variation in the square root of negative one.

Sqrt(-1) is representation of capacitance or inductance. Changing the inductance with a mag amp setup like you describe would theoretically allow for excess energy to flow into the system.

Good work Jeremy!

Dave

[Turion]

The regular bicycle wheel (steel rim) with threaded rod attached and a strip of plastic to form the new wheel works pretty well. The rods (as spokes) are really solid. I used some thin plastic as a temporary wheel to get the spacing right. As soon as it is all done, I will use the thin plastic as a template to drill the holes in the thicker stuff. Probably won't have it all put together until Monday, and then will begin to glue magnets in place, Have my wire ordered, so will begin winding coils as soon as it gets here. This will be about a six foot wheel.

[redrichie]

Jeremy,
I know your busy with school/ Is it possible to post your drawings in a way I can enlarge them? I would love to see what you drew. Thanks man.

[chuck H]

You may have my wife's ph number the last to numbers of hers is 00 mine is 01 other then that thy are the same she is at work so she will not answer sorry for being off topic Thanks William

@ William. Call was meant for chuck H
@ JB, Thankyou very much for the help. see video on you tube. next will be timing wheel and Bedini/Cole switch with cap dump. Exciting stuff coming guys/gals...
YouTube - 1210102253

[Mark]

Hi Chuck

Can't really see much on that video its too blurry. I've had my 3 pole kit running for a week now on the 1/2 Bedini cole switch. With 12 volts I can run it on as low as 23ma @2170rpm (1 battery set up). With 36 volts 120ma @ 7500rpm.

Mark

[rosehillworks]

Thanks John B for your answer. Chuck H thanks for the correction. William

[gyula]

Woopy,
Good video nice spike. If you would build the Bi-Polar switch you would be free of that supply. Then it would be easy to tap the energy to the cap and switch it back.
John B

Hi John,

Would like to know whether you meant Woopy could get a self runner when using the Bi-polar switch?

I assume a rechargable battery would still be needed to replace his power supply and those huge voltage spikes stored in the cap could recharge the battery in the off time, this is how you meant and this process could maintain the starting battery energy state, right?

If Woopy used a huge value capacitor instead of the battery, charged up first to 8V or so from a separate supply then use it as an energy source or sink, could he receive a few hours operation from it? I mean the COP of this setup is very near to 1 like 0.999.
Putting this otherwise: the chemical reaction inside the battery may make this setup to have a COP of 1.03 or so, maybe a bit higher but using a huge value capacitor the COP goes just under 1. Are these correct assumptions?

Thanks, Gyula

[Matthew Jones]

Hi Chuck
Can't really see much on that video its too blurry. I've had my 3 pole kit running for a week now on the 1/2 Bedini cole switch. With 12 volts I can run it on as low as 23ma @2170rpm (1 battery set up). With 36 volts 120ma @ 7500rpm.
Mark

How did you wire it up Mark?

Thanks
Matt

[woopy]

Thanks John for the advice

so i made it with quite good basic results, please see the video

I think it is what you suggested , a bipolar switch , is it OK ? or i am wrong ?

But now i have some question marks, as how to pull back this energy back on the input basis?

And much more important yet is the timing, as i can see the Led lamp is much more powerfull when the rotor is slow, but when i replace the leds with a DC small motor i only can get some spinning at higher input voltage (about 10 volts or more) and higher RPM ??

the learning program seems to be long but fascinating

good luck at all

Laurent

YouTube - pulse motor with PMH armature test 2.wmv

[Matthew Jones]

Thanks John for the advice
so i made it with quite good basic results, please see the video
I think it is what you suggested , a bipolar switch , is it OK ? or i am wrong ?
But now i have some question marks, as how to pull back this energy back on the input basis?
And much more important yet is the timing, as i can see the Led lamp is much more powerfull when the rotor is slow, but when i replace the leds with a DC small motor i only can get some spinning at higher input voltage (about 10 volts or more) and higher RPM ??
the learning program seems to be long but fascinating
good luck at all
Laurent
YouTube - pulse motor with PMH armature test 2.wmv

Seems that you should go slower. Same thing happens to monopole if you time it to run too fast the spike drop.
Your looking for a good spike. And few of them.
If you set yourself up with a high farad capacitor in the beginning, like a 12 volt 1/2 farad or battery (Maybe) and low farad in the back like you have you can make a cap dump back to the front.

http://www.matthewcjones.com/power/CapDumper.jpg

Thats the cap dumper I was using earlier. It was based on a solid state relay. There are several other ways to do it.
I am not sure how it would sustain itself but it would defendantly lower your over all draw. The cap dumper is a neat thing. IT puts a new twist on things for sure.

Also if you do another video I would like to see the draw on the power supply if possible. Just a request.

Cheers
Matt

[Mark]

How did you wire it up Mark?

Thanks
Matt

Using one wire off the bifilar as the trigger. All 3 coils in parallel. 2200 ohm resistor from collector of mpsa06 to base of MJL21193. 18000 ohm resistor on trigger to base of mpsa06. I just recently removed the resistors from base to emmiter on both 91193 and 21194, no noticeable difference. Resistors are all 1/2 watt. Outputs from both collectors of 21193 & 21194 to full bridge of 1n4007's and 10uf 250v cap back to source. This set up was 25ma 12 volts @ 2310 rpm's.

I'm still playing with it to see how much lower I can go on input. Any other questions let me know.

Mark