Joule Ringer!

[T-1000]

T-1000,

I think SkyWatcher's schematic shows a simple 1:1 typical toroid bifilar series wrap, and not a transformer with pins. Simply placing a very low level capacitor next to the 10K base resistor should bring SkyWalker's circuit into resonance. Ater lightining the neon and placing a ground wire on the transistor pin, you suggest we place a current transformer between the pin and the ground wire to measure current running from the transistor into the ground? Current transformers are used extensively for measuring current, is this the reason?

Where you got wires from transfomer, in resonance it should lit small neon bulb from single wire when your hand is handling glass of it. If that happens, it is place where external energy input can be used and with current transformer (also in resonance) you can try take energy out without affecting your circuit....

[Allen Burgess]

Current Transformer

T-1000,

I think SkyWatcher's schematic shows a simple 1:1 typical toroid bifilar series wrap, and not a transformer with pins. Simply placing a very low level capacitor next to the 10K base resistor should bring SkyWalker's circuit into resonance. Ater lightining the neon and placing a ground wire on the transistor pin, you suggest we place a current transformer between the pin and the ground wire to measure current running from the transistor into the ground? Current transformers are used extensively for measuring current, is this the reason?

[T-1000]

Hi folks, this circuit is showing some promising results.

When looking on this circuit, it reminds me about energy recycling probably going on here...

If you run this circuit in resonance and will get small neon bulb lit from single wire in any pin of transformer, then you can freely attach earth ground to that place and see if you get current over single wire (hint: put current transformer there).

Good luck!

[Allen Burgess]

"Split Positive" Super Joule Thief.

I want to try and combine SkyWatcher's "Split Positive" recharging circuit with Lasersaber's Super Joule Thief along with three rechargable six volt batteries. I have to begin by ordering a Metglass Toroid. I'll run some tests this Spring when I return home and try to upload a video with the test results in a few months. Has anyone already tried to scale SkyWatcher's "Split Positive" recharging circuit up to the twelve volts used by Lasersaber's Super Joule Thief on the Super Joule Thief primary?

[SkyWatcher]

Hi folks, this circuit is showing some promising results.
The voltage seems to be maintaining and possibly slightly increasing overall by rotating the AA nimh cells using the method shown in the circuit diagram similar to what Bedini has shown.


Uploaded with ImageShack.us
peace love light
tyson

[Neight]

Ok, it ain't magic, but it's still pretty cool!
12.5 hours and the primary battery only technically lost .01V (down to 1.13 from initial 1.14) and the charge battery is now at 1.02 (up from .98).
so all told, I am still in energy gained territory, and still getting great light out of the white LED

[woopy]

Hi all

I stumbled upon the thread of "Sergdo" (a russian participant at OU )

and i replicated what he proposed.
I don't know if every body has already tried it ??

hope this helps

good luck at all

Laurent

Amazing light with low power toroid transformer 1.wmv - YouTube

[Neight]

Hey guys!
I have been playing around with what lasersaber calls the super efficient joule ringer, and lidmotor says is a variation of a blocking oscillator. Not sure what it is exactly, but I know it works, and pretty dang well....
I wired this thing up with a dead AA battery in series with the LED across the 2n2222a tranny, to see how well, or even if it would charge a battery.
It's been running for well over an hour now, and I am pretty excited by what I see so far.
at the beginning of the test, once the circuit was turned on, the voltage of the primary AA was 1.14V loaded, and the charging AA battery was .98V
after nearly an hour and a half, the primary is now sitting at 1.15V while the charging battery is reading 1V.
I am not sure what exactly is happening here, and I know an hour and a half isn't much time for a test like this, but so far, I am ahead on both sides of the circuit.
If this keeps up like this for any length of time, I will report back with how well it performed.
Just wanted to throw this out there, in case anyone else wanted to try it

N8

Nearly 4 hours in and primary battery is still 1.15V and the charge battery is now 1.01V, still charging. It is very slow, but interesting to see how well it's working

[aaron5120]

Hi sorry for the quick sketcth I made since im bedridden right now and just want to pass the info in a hurry anyway

1 c is the collector from the transistor just touching the toroid
2. transformer 15 0 15 input out put 110 0 0 110 30 watts
3. standard xee2 joule ringer - to emitter + to 0 (in center tap)
left to Collector 15 right to base trigger 15
4. Output 110 110 to parallel led lamps 9 pcs 5 watts 220 v ac
0 to 2 ceramic ring magnets then to a toroid going to the positive of battery
0 going to to toroid with open end

hope this help

totoalas

Thanks Totoalas, take a rest and get well soon. thanks for the clarification. I think I figured it out now.
Will post results when I get the circuit hooked up. The Xee2 JR circuit seems to be the one titled "joule thief with 120VAC led bulb part 7" in his YT channel. You made an advancement to Xee2's ckt, placing a magnetic coupling mechanism to the transformer. So the ceramic magnets and the ferrite toroid constitute the innovation herein for a feedback to the source.
Great job, Totoalas. Must try this idea.
aaron5120

[SkyWatcher]

Hi folks, this circuit though probably similar to many before, seems to be performing well.
The single 1.2 volt nimh is gaining equal or greater voltage than what the two 1.2 volt nimh in series are losing.
I know usually people hook up two in parallel on the charging side, though the higher resistance of the single cell seems to be working well lighting up a single white led close to full brightness.
here is a diagram of the simple circuit, let me know what you think and if you try it, let me know how it is working, thanks.


Uploaded with ImageShack.us
peace love light
tyson

[Allen Burgess]

Illness

Totoalas,

Keep your fluids up! Thanks for the key to the schematic. The blue wire from the collector to just touching the toroid looks as though it may be acting as a spark gap generator. Perhaps you really are on to something here, like Mopozco's latest light circuits. We need to clean the schematic up. Good work. Thanks again.

[totoalas]

Hi Totoalas,
I tried to catch up with your sketch, but am confused with some of the components, for instance, what is the component "c", which has 5 leads in it? Is it the Joule Ringer circuit? So can you draw out the circuit in the sketch ?
In your previous clips of YT, the transformer has 110V--0, 0--110V in its primary, then 15V--0--15V in the secondary. Now this is not the same in your sketch showed. And also I cannot find out where is the output to the led lamps in the sketch.
Please clarify or make some indications in your sketch. Thank you in advance.
aaron5120

Hi sorry for the quick sketcth I made since im bedridden right now and just want to pass the info in a hurry anyway

1 c is the collector from the transistor just touching the toroid
2. transformer 15 0 15 input out put 110 0 0 110 30 watts
3. standard xee2 joule ringer - to emitter + to 0 (in center tap)
left to Collector 15 right to base trigger 15
4. Output 110 110 to parallel led lamps 9 pcs 5 watts 220 v ac
0 to 2 ceramic ring magnets then to a toroid going to the positive of battery
0 going to to toroid with open end

hope this help

totoalas

[aaron5120]

Uploaded with ImageShack.us

this a rough sketch of my st up

totoalas

Hi Totoalas,
I tried to catch up with your sketch, but am confused with some of the components, for instance, what is the component "c", which has 5 leads in it? Is it the Joule Ringer circuit? So can you draw out the circuit in the sketch ?
In your previous clips of YT, the transformer has 110V--0, 0--110V in its primary, then 15V--0--15V in the secondary. Now this is not the same in your sketch showed. And also I cannot find out where is the output to the led lamps in the sketch.
Please clarify or make some indications in your sketch. Thank you in advance.
aaron5120

[totoalas]

Hi totoalas
its good to see you making all these good stuff but I appriciate if you can post a schematic so we can understand it butter.

good luck

Ehsan

Uploaded with ImageShack.us

this a rough sketch of my st up

totoalas

[jehdds]

wind a shorted coil like Eds pmh under your super joule ringer, bring the aether to you.
dave

Figured it out. Got it thank you for the hint.
Perpetual Motion Holder Diagram
Very Best Regards,
Jim